ICON PFIVEX73313.0 User Manual - Assembly

Summary of PFIVEX73313.0

  • Page 1

    Userʼs manual visit our website www.Iconsupport.Eu model no. Pfivex73313.0 serial no. : ___________ caution read all precautions and instruc- tions in this manual before using this equipment. Keep this manual for future reference. Questions ? If you have questions, or if there are missing parts, ple...

  • Page 2: Table of Contents

    2 table of contents warning decal placement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 important precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Page 3: Important Precautions

    3 important precautions warning : to reduce the risk of serious injury, read all important precautions and instructions in this manual and all warnings on your bike before using it. Icon assumes no responsibility for personal injury or property damage sustained by or through the use of this product....

  • Page 4: Before You Begin

    4 before you begin thank you for purchasing the proform® saturn. The bike provides an array of features designed to make your workouts at home more effective and enjoyable. For your benefit, read this manual carefully be- fore you use the bike. If you have questions after reading this manual, please...

  • Page 5: Assembly

    5 assembly assembly requires two persons. Place all parts of the elliptical exerciser in a cleared area and re- move the packing materials. Do not dispose of the packing materials until assembly is completed. In addition to the included tool(s), assembly requires a phillips screwdriver and an adjust...

  • Page 6

    6 step 1 attach front stabilizer (2) and rear stabilizer (4) to main frame (1) by fixing carriage bolt(6), arc wash- ers(8) and cap nut (9) step 2 thread the right pedal (11r)which marked “r” onto the right side of the crank(10) , then circumvolved easilly and tighten; do the same way to thread the ...

  • Page 7

    7 step 4 pull the handlebar wire(25) out of the hole of upright post post (17) ,then put the handlebar (24) onto the upright post (17) by using washer (23) and inner hex bolt(21)&spring washer(22) , then cover with the handlebar chuck cover (20). Step 5 connect the handlebar wire (25) and the extend...

  • Page 8: How to Operate The Bike

    8 how to adjust the height and the lateral position of the seat for effective exercise, the seat should be at the proper height. As you pedal, there should be a slight bend in your knees when the pedals are in the lowest position. To adjust the height of the seat, first loosen the seat post knob. Ne...

  • Page 9

    9 measure your heart rate if desired you can measure you heart rate using either the handgrip pulse sensor or the optional chest pulse sensor. Note: if you hold the handgrip pulse sensor and wear the chest pulse sensor at the same time, the console will not display your heart rate accurately. If the...

  • Page 10

    10 iinspect and tighten all parts of the exercise cycle regularly. Replace any worn parts immediately. To clean the exercise cycle, use a damp cloth and a small amount of mild detergent. Important: to avoid damaging the console, keep liquids away from the console and keep the console out of direct s...

  • Page 11: Console Features

    11 console features follow your progress with the display. The console has one display that show the following workout information : speed—this display shows your pedaling speed, in kilometer per hour (km/h). Time—this display shows the elapsed time. Distance—this display shows the distance you have...

  • Page 12: Exercise Guidelines

    12 exercise guidelines warning: before beginning this or any exercise pro- gram, consult your physician. This is espe- cially important for persons over the age of 35 or persons with pre-existing health problems. The pulse sensor is not a medical device. Vari- ous factors may affect the accuracy of ...

  • Page 13

    13 exploded drawing—model no. Pfivex73313.0 part 1.

  • Page 14

    14 exploded drawing—model no. Pfivex73313.0 part 2.

  • Page 15

    15 part list—model no. Pfivex73313.0 item 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 description belt tray belt hex screw spring washer spring washer magnet board axle magnet board spring hex screw hex nut bearing elastic c...

  • Page 16: Ordering Replacement Parts

    Ordering replacement parts to order replacement parts, please see the front cover of this manual. To help us assist you, be prepared to provide the following information when contacting us: • the model number and serial number of the product (see the front cover of this manual) • the name of the pro...