- DL manuals
- Icop
- Processor
- VSX-6157
- User manual
Icop VSX-6157 User manual
Summary of VSX-6157
Page 1
Vsx-6157 dm&p vortex86sx 300mhz pc/104 cpu module with 4s/2usb/vga/lcd/3lan/gpio 128mb ddr2 onboard user’s manual (revision 1.0a).
Page 2: Copyright
Copyright the information in this manual is subject to change without notice for continuous improvement in the product. All rights are reserved. The manufacturer assumes no responsibility for any inaccuracies that may be contained in this document. And makes no commitment to update or to keep curren...
Page 3
T a b l e o f c o n t e n t s t a b l e o f c o n t e n t s .............................................................Iii c h a p t e r 1 introduction……………………………………………1 1.1 packing list............................................................ 1 1.2 product description.............................
Page 4: C H A P T E R 1
Vortex86sx-6157 vortex86sx™ pc/104 cpu module 1 c h a p t e r 1 introduction 1.1 packing list product name package vsx-6157 embedded vortex86sx cpu all-in-one board manual & drivers cd x 1 rs232 cable x 4 printer cable x1 ide cable x 1 usb cable x 1 (usb port x 2 ) vga cable x 1 lan cable x 3 gpio c...
Page 5: 1.2 Product Description
Vortex86sx-6157 vortex86sx™ pc/104 cpu module 2 1.2 product description the vsx-6157 family of low-power x86 embedded controller is designed to meet pc/104 specification, and integrated with the following features. 300 mhz vortex86sx system-on-chip vga, tft lcd support up to 1280x1024 resolution 128...
Page 6: 1.3 Specifications
Vortex86sx-6157 vortex86sx™ pc/104 cpu module 3 1.3 specifications features vsx-6157 cpu dm&p soc cpu vortex86sx- 300mhz real time clock with lithium battery backup cache l1:16k i-cache, 16k d-cache bios ami bios bus interface pc/104 standard compliant system memory 128mb ddr2 onboard watchdog timer...
Page 7
Vortex86sx-6157 vortex86sx™ pc/104 cpu module 4 flash disk support onboard 2mb spi flash disk (driver: a) 44-pin ide flash disk( embeddisk 16mb or above) power requirement single voltage +5v@580ma dimension 90 x 96mm (3.54 x 3.77 inches) weight 90g operating temperature -20 o c ~ +70 o c -40°c ~ +85...
Page 8: 1.4 Board Dimension
Vortex86sx-6157 vortex86sx™ pc/104 cpu module 5 1.4 board dimension.
Page 9: Installation
Vortex86sx-6157 vortex86sx™ pc/104 cpu module 6 c h a p t e r 2 installation 2.1 board outline note: 1-redundancy signal and system-fail-sw are optional.
Page 10
Vortex86sx-6157 vortex86sx™ pc/104 cpu module 7 2.2 connectors & jumpers location.
Page 11: Jumpers & Leds
Vortex86sx-6157 vortex86sx™ pc/104 cpu module 8 jumpers & leds.
Page 12: Summary Table
Vortex86sx-6157 vortex86sx™ pc/104 cpu module 9 2.3 connectors & jumpers summary summary table nbr description type of connections pin nbrs. J1 ide box header, 2.0 ∅ ,22x2 44-pin j2 usb box header,2.0 ∅ , 5x2 10-pin j4 lan 1 pin header, 2.0 ∅ , 4x2 8-pin j5 jtag box header, 125 ∅ , 6x1 6-pin j6 rese...
Page 13
Vortex86sx-6157 vortex86sx™ pc/104 cpu module 10 j38 buzzer pin header, 2.54 ∅ , 2x1 2-pin pwr- led power active led (red) led-smd ide- led ide active led (green ) led-smd mtbf- led mtbf-out (orange) led-smd led 4 lan link/active led (green) led-smd led 5 lan duplex led ( yellow ) led-smd led 6 lan ...
Page 14: J1: Ide (44 Pins)
Vortex86sx-6157 vortex86sx™ pc/104 cpu module 11 2.4 pin assignments & jumper settings j1: ide (44 pins) j2: usb pin # signal name pin # signal name 1 vcc 2 vcc 3 lusbd0- 4 lusbd1- 5 lusbd0+ 6 lusbd1+ 7 gnd 8 gnd 9 ggnd 10 ggnd pin # signal name pin # signal name 1 iderst 2 gnd 3 ided7 4 ided8 5 ide...
Page 15: J4: Lan1
Vortex86sx-6157 vortex86sx™ pc/104 cpu module 12 j4: lan1 pin # signal name pin # signal name 1 atx+ 2 atx- 3 arx+ 4 led0 5 led0+ 6 arx- 7 led1+ 8 led1 j5: jtag pin # signal name pin # signal name 1 vcc 2 gnd 3 tck 4 tdo 5 tdi 6 tms j6: reset pin # signal name pin # signal name 1 reset 2 gnd j7: red...
Page 16: J9: Ps/2 Keyboard
Vortex86sx-6157 vortex86sx™ pc/104 cpu module 13 j9: ps/2 keyboard pin # signal name pin # signal name 1 kbclk 2 kbdat 3 nc 4 gnd 5 vcc j10: ps/2 mouse pin # signal name pin # signal name 1 msclk 2 msdata 3 nc 4 gnd 5 vcc j11: com 1 pin # signal name pin # signal name 1 dcd1 2 rxd1 3 txd1 4 dtr1 5 g...
Page 17: J13: Gpio (Port 0 / 1)
Vortex86sx-6157 vortex86sx™ pc/104 cpu module 14 j13: gpio (port 0 / 1) j15: rs485 (auto direction) j16: power connector (terminal block 5.0mm) pin # signal name 1 +5v 2 gnd j17: com3 pin # signal name pin # signal name 1 dcd3 2 rxd3 3 txd3 4 dtr3 5 gnd 6 dsr3 7 rts3 8 cts3 9 ri3 10 nc pin # signal ...
Page 18: J18: Print
Vortex86sx-6157 vortex86sx™ pc/104 cpu module 15 j18: print pin # signal name pin # signal name 1 stb- 14 afd- 2 pd0 15 err- 3 pd1 16 init- 4 pd2 17 slin- 5 pd3 18 gnd 6 pd4 19 gnd 7 pd5 20 gnd 8 pd6 21 gnd 9 pd7 22 gnd 10 ack- 23 gnd 11 busy 24 gnd 12 pe 25 gnd 13 slct 26 nc j19: com4 pin # signal ...
Page 19
Vortex86sx-6157 vortex86sx™ pc/104 cpu module 16 j20: pc104 connector – 64pin pin # signal name pin # signal name 1 iochchk * 2 gnd 3 sd7 4 resetdrv 5 sd6 6 vcc 7 sd5 8 irq9 9 sd4 10 -5v 11 sd3 12 drq2 13 sd2 14 -12v 15 sd1 16 ows 17 sd0 18 +12v 19 iochrdy 20 gnd 21 aen 22 smemw * 23 sa19 24 smemr *...
Page 20
Vortex86sx-6157 vortex86sx™ pc/104 cpu module 17 j21: pc104 connector – 40pin j22: 4p power source (interconnect to pc/104 – j20) pin # signal name 1 -5v 2 -12v 3 +12v 4 gnd pin # signal name pin # signal name 1 gnd 2 gnd 3 memcs16 * 4 sbhe * 5 iocs16 * 6 sa23 7 irq10 8 sa22 9 irq11 10 sa21 11 irq12...
Page 21: J24: Vga
Vortex86sx-6157 vortex86sx™ pc/104 cpu module 18 j24: vga pin # signal name pin # signal name 1 r out 2 gnd 3 g out 4 gnd 5 b out 6 gnd 7 hsync 8 gnd 9 vsyncd 10 gnd j25: lcd (dvo) connector pin # signal name pin # signal name 1 vcc3 2 vcc3 3 lg2 4 lg3 5 lg4 6 lg5 7 nc 8 nc 9 lr0 10 lr1 11 lr2 12 lr...
Page 22
Vortex86sx-6157 vortex86sx™ pc/104 cpu module 19 j26~j31: display type setup (crt /lcd) connector pin # signal name 1 vcc 2 gpioa j26 3 gnd 1 vcc 2 gpiob j27 3 gnd 1 vcc 2 gpioc j28 3 gnd 1 vcc 2 gpiod j29 3 gnd 1 vcc 2 gpioe j30 3 gnd 1 vcc 2 gpiof j31 3 gnd (please refer to appendix d, for display...
Page 23: J32:
Vortex86sx-6157 vortex86sx™ pc/104 cpu module 20 j32: rs232 com2 operation mode selector pin combination description 1-2 com2 rs232 3-4 rs485 5-6 rs422 j33 /j34 /j35: com2: rs232 /rs422 setting rs232 (close) rs422 (close) j33 j34 j34 j35 1 1 1 1 2 2 2 2 3 3 3 3 4 4 4 4 j36: lan2 pin # signal name pi...
Page 24: 2.5
Vortex86sx-6157 vortex86sx™ pc/104 cpu module 21 2.5 system mapping.
Page 25
Vortex86sx-6157 vortex86sx™ pc/104 cpu module 22.
Page 26
Vortex86sx-6157 vortex86sx™ pc/104 cpu module 23.
Page 27: 2.6 Watchdog
Vortex86sx-6157 vortex86sx™ pc/104 cpu module 24 2.6 watchdog timer there are two watchdog timers in vortex86sx cpu. One is compatible with m6117d watchdog timer and the other is new. The m6117d compatible watchdog timer is called wdt0 and new one is called wdt1. We also provide dos, linux and wince...
Page 28: 2.7 Gpio
Vortex86sx-6157 vortex86sx™ pc/104 cpu module 25 2.7 gpio (general purpose input / output) 40 gpio pins are provided by the vortex86sx for general usage in the system. All gpio pins are independent and can be configured as inputs or outputs, with or without pull-up/pull-down resistors. We also offer...
Page 29
Vortex86sx-6157 vortex86sx™ pc/104 cpu module 26 2.8 spi flash (serial peripheral interface) as spi flash ( serial peripheral interface) offers many benefits including: reduced controller pin count, smaller and simpler pcbs, reduced switching noise, less power consumption, and lower system cost many...
Page 30: Driver Installation
Vortex86sx-6157 vortex86sx™ pc/104 cpu module 27 c h a p t e r 3 driver installation vga thevortex86sx processor also use external display chip ““volari™ z9s” which is an ultra low powered graphics chipset with total power consumption at around 1-1.5 w. It is capable in providing vga display output ...
Page 31: Appendix
Vortex86sx-6157 vortex86sx™ pc/104 cpu module 28 appendix a. Tft flat panel data output.
Page 32: Size
Vortex86sx-6157 vortex86sx™ pc/104 cpu module 29 b.Tft flat panel support list size brand resolution model no. 5.7” sharp 320x240 lq057q3dc02 5.7” kyocera 320x240 tcg057qv1ac-g10 5.7” pvi 320x240 pd057vu4 / pd057vu5 5.7” data image 640x480 fg050710dsswjg01 5.7” ampire 640x480 am-640480gtmqw-t00h 5.7...
Page 33: Icop–0096
Vortex86sx-6157 vortex86sx™ pc/104 cpu module 30 c. Lvds flat panel support list if you would like to use lvds flat panel with vortex86sx series, please contact our regional sales to get icop-0096 information or visit icop website: http://www.Icop.Com.Tw/products_detail.Asp?Productid=178 icop–0096 :...
Page 34: Display Type Setup
Vortex86sx-6157 vortex86sx™ pc/104 cpu module 31 d. Flat panel hardware setting: the vortex86sx-6157 offers the hardware setting for the various tft lcd flat panels support and please make sure the jumper setting (j26~j31) before you connect the lcd. Display type setup connector lcd 1-2 2-3 j26 c j2...
Page 35: Hardware
Vortex86sx-6157 vortex86sx™ pc/104 cpu module 32 e. Flat panel wiring and lighting hardware before you connect the tft lcd flat panel with vortex86sx-6157, please make sure that the input voltage of lcd is 3.3v or not bios please contact or e-mail our regional sales to get the special bios for the a...
Page 36
Vortex86sx-6157 vortex86sx™ pc/104 cpu module 33 f. Tcp/ip library for dos real mode dsock is a tcp/ip library for dos real mode, which is used by rsip. It provides simple c functions for programmer to write internet applications. Icop also provide internet examples using dsock: bootp/dhcp, ftp serv...
Page 37: G. Bios Default Setting
Vortex86sx-6157 vortex86sx™ pc/104 cpu module 34 g. Bios default setting if the system cannot be booted after bios changes are made, please follow below procedures in order to restore the cmos as default setting. Press “end” key, when the power on press to enter the ami bios setup press “f9” to load...
Page 38: Warranty
Vortex86sx-6157 vortex86sx™ pc/104 cpu module 35 warranty this product is warranted to be in good working order for a period of one year from the date of purchase. Should this product fail to be in good working order at any time during this period, we will, at our option, replace or repair it at no ...