Summary of D1700.1
Page 1
Mono channel class "d" automotive amplifier instruction manual d900.1 / d1700.1 / d3000.1.
Page 3
Please read all instructions before installation ! Free installation. Congratulations on your purchase your new high fidelity mono block amplifier is designed to deliver maximum enjoyment and one year of trouble free service. Please take a few moments to read this manual thoroughly. It will explain ...
Page 4
Installation 1. After reading precaution, decide where you are going to install the unit. Also, see fig.1. 2. Once the location has been determined, place the amplifier into position. Using a felt tip pen or pencil mark the four holes to be drilled for mounting. Never use the amplifier as a template...
Page 5
Power gnd +12v rem on protect speaker fuse power gnd +12v rem on protect speaker fuse the class "d" amplifier is a single channel dedicated subwoofer amplifier. Unlike other amplifiers, the class "d" operates as a single channel and cannot be bridged. Don't be fooled by the outputs. Two outputs are ...
Page 6
4 from radio mono bridged remocon gain l.P.F bass boost 50hz 250hz l r line input slave 6v 0.2v master slave 0db 12db remocon gain l.P.F bass boost 50hz 250hz l r line input slave 6v 0.2v master slave 0db 12db wiring subwoofers (dual amps) when using dual amplifiers to power one subwoofer, the posit...
Page 7
5 mono bridged master amplifier slave amplifier (option) two amplifier/ one subwoofer (single voice coil)configuration power gnd +12v rem on protect speaker fuse power gnd +12v rem on protect speaker fuse chassis ground remote turn on battery via fuse using a lead wire of 8 gauge or bigger connect f...
Page 8
Mono bridged (option) four amplifier/ one subwoofer (dual voice coil)configuration 6 master amplifier slave amplifier power gnd +12v rem on protect speaker fuse power gnd +12v rem on protect speaker fuse master amplifier slave amplifier power gnd +12v rem on protect speaker fuse power gnd +12v rem o...
Page 9
7 the proper wire size is very important for an amplifier of this power level. Beca use the class "d" amplifier is capable of drawing in excess of 90 amperes,4 gauge wire is recommended for lengths up to twenty feet. If a longer length is needed , a larger gauge amplifier power wire should be wired ...
Page 10
8 1 2 3 4 5 6 7 1. Rca input jacks 2. Input level control 3. Low pass frequency 4. Bass boost 5. Remote control jack 6. Master/slave switch 7. Slave input jack operation remocon gain l.P.F bass boost 50hz 250hz l r line input slave 6v 0.2v master slave 0db 12db control and crossover 1. Rca input jac...
Page 11
Remocon gain l.P.F bass boost 50hz 250hz l r line input slave 6v 0.2v master slave 0db 12db 9 front/rear panel power gnd +12v rem on protect speaker d3000.1 power gnd +12v rem on protect speaker fuse 30a 30a 30a d1700.1 power gnd +12v rem on protect speaker fuse 25a 25a 25a d900.1 d900.1, d1700.1, d...
Page 12
10 this section provides you with a catalog of amplifier symptoms and their probable causes and solutions. Before you consult this listing, make sure the vehicle's electrical system is working properly by verifying that other electrical items (e. G. Headlights, windows, etc.) still function correctl...
Page 13
11 note : specifications & design subject to change without notice for improvements. Specification amplifier d900.1 d1700.1 d3000.1 rms power / 1 ohm @ 1% t.H.D 900w x 1 1700w x 1 3000w x 1 650w x 1 1000w x 1 2000w x 1 350w x 1 500w x 1 1000w x 1 90% 90% 90% 79% 79% 79% 10hz ~ 250hz 10hz ~ 250hz 10h...
Page 16
Interfire audio, inc. Santa fe springs, ca 90670 www.Interfireaudio.Com printed in korea.