Intermec AD10 Supplementary Manual
1
AD10 Compliance Insert
For Users in the United States and Canada
The users of this product are cautioned to use accessories and peripherals approved by Intermec Technologies Corporation. The use of
accessories other than those recommended, or changes to this product that are not approved by Intermec Technologies Corporation, may
void the compliance of this product and may result in the loss of the user’s authority to operate the equipment.
Les utilisateurs de ce produit sont avisés d’utiliser des accessoires et des périphériques approuvés par Intermec Technologies Corporation.
L’utilisation d’accessoires autres que ceux recommandés ou des changements à ce produit qui ne sont pas approuvés par Intermec
Technologies Corporation peuvent annuler la conformité de ce produit et mettre fin au droit qu’a l’usager d’utiliser l'équipement.
FCC Digital Emissions Compliance
Intermec Model AD10 has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of the following measures:
•
Reorient or relocate the radio or television receiving antenna.
•
Increase the separation between the computer equipment and receiver.
•
Connect the equipment into an outlet on a circuit different from that to which the radio or television receiver is connected.
•
Consult the dealer or an experienced radio television technician for help.
Canadian Digital Apparatus Compliance
These Class B digital products meet all requirements of the Canadian Interference-Causing Equipment Regulations.
Conformité aux normes canadiennes sur les appareils numériques
Cet appareil numérique de la classe B respecte toutes les exigences du Réglement sur le matériel brouilleur du Canada.
Battery Information
Battery Recycling Information
Note: In the U.S.A., the EPA does not consider spent Li-ion batteries as hazardous waste.
Caution: This marking indicates that the user should read all included documentation before use.
Attention: Ce marquage indique que l’usager doit, avant l’utilisation, lire toute la documentation incluse.
Caution: For use with Intermec Model CN3 and battery pack models AB8 & AB9. For power supply use Intermec Model
073573. No user-servicable parts.
Attention: Pour utilisation avec le modèle Intermec CN3 et les modèles de bloc-piles AB8 et AB9. Pour la source d’alimentation,
utilisez Intermec modèle 073573. Il ne contient aucune pièce réparable par l’utilisateur.
Caution: Use only Intermec battery pack Models AB8 or AB9. Risk of fire or explosion if incorrect battery pack is used.
Promptly dispose of used battery pack according to the instructions.
Attention: Utiliser les bloc-piles Intermec AB8 ou AB9 seulement. L’utilisation d’un mauvais bloc-piles pourrait constituer un
risque d’incendie ou d’explosion. Mettre rapidement au rebut tout bloc-piles usé, conformément aux instructions.
Li-ion
Li-ion
This product contains or uses a lithium ion (Li-ion) main battery. When the battery reaches the end of its useful life, the
spent battery should be disposed of by a qualified recycler or hazardous materials handler. Do not mix this battery with the
solid waste stream. Contact your Intermec Technologies Service Center for recycling or disposal information.
Ce produit contient une batterie principale d’ions de lithium (Li-ion) et une batterie. Lorsque la batterie atteint la fin de sa
durée de vie utile, la batterie usées doivent être mises aux rebuts par un agent de recyclage ou un manipulateur de
matériaux dangereux agréé. Il ne faut pas mélanger la batterie aux autres déchets solides. Pour plus d’informations sur le
recyclage ou la mise aux rebuts, contacter votre centre de services Intermec Technologies.