Getting started guide scanplus 1802 cordless system.
2 3 step 1 step 2 step 3 quick setup pc keyboard wedge cable or usb cable .......... 4 rs-232 c cable............................................................ 6 return to the default setup.............................................. 9 using more than one cordless system ...........................
2 3 step 1 recommendations recommended not recommended 0 - 15 m (0 - 50 ft) 15 - 25 m (50 - 80 ft) the microbar 9735 must not be connected by the rj connectors to any type of telecom- munications circuits..
4 step 2 pc wedge cable p/n 3-414037-11 keyboard wedge or usb (pc) connect base station system power off system power on associate cordless scanner(s) recharge battery "beep beep" only do this if you are using a keyboard wedge or a usb cable. Usb cable p/n 3-414038-11 port 3 keyboard wedge cable usb...
5 azerty french qwertz german qwerty english select keyboard qwerty italian qwerty danish qwertz swiss / french qwerty swedish / finnish qwerty spanish qwerty portuguese qwerty norwegian postamble = carriage return postamble = tab postamble = enter (*) postamble = none customize parameters (optional...
6 7 step 2 read this code (standard rs- 232 c pc serial port compa- tible) 9600 baud, 7 data bits, even parity, 2 stop bits postamble = carriage return + line feed associate cordless scanner(s) system power on connect base station direct rs-232 cable p/n 3-414032-10 system power off recharge battery...
6 7 customize parameters (optional) (*) = default value postamble = carriage return + line feed (*) postamble = none postamble = carriage return even parity no parity odd parity 7 data bits 8 data bits 19200 baud 9600 baud.
8 9 pdf417 code 39 code 128 / ean 128 upc-a, upc-e, ean-8, ean-13 (upc-a -> upc-a) upc-a, upc-e, ean-8, ean-13 (upc-a -> ean-13) step 3 symbologies select symbology disable all symbologies set symbologies for each cordless scanner. Use the bar codes on the back cover to test your setup.
8 9 default setup using more than one cordless system when using more than one cordless system in the same area, we strongly recommend using different channels for optimal performance. North american version 906mhz - channel 2 european version 433mhz - channel 5 channel 1 channel 2.
10 11 full setup with easyset connect base station associate cordless scanner(s) start the easyset software send setup bar codes to the easyset setup sheet print setup sheet read the bar codes on the setup sheet "beep beep".
10 11 operation read barcode good read "beep" data transmission data transmission acknowledgement add more scanners you can associate more cordless scanners with the base station at any time. Set symbologies (see page 8) read association bar code out of range "beep beep beep beep beep beep" low batt...
12 13 regulatory statements intermec hereby declares that the scanplus 1802 cordless system has been tested and found compliant with the below listed standards as required by the r&tte directive 99/05/ec, emc directive 89/336/eec as amended by 92/31/eec and by the low voltage directive 73/23/eec as ...
12 13.
North america / asia pacific / latin america • 6001 36th avenue west, po box 4280, everett, wa 98203-9280 tel: +1 425 348 2600 • fax: +1 425 348 2833 • u.S. Service and technical support, tel: + 1 800 755 5505 • canadian service and technical support, tel: + 1 800 668 7043 europe / middle east / afr...
Test barcodes part number: 3-235049-01 rev. J all rights reserved © 2006 intermec technologies corporation.
