1. DL manuals
  2. Intermec
  3. Barcode Reader
  4. Transaction Manager 9560
  5. User Manual

Intermec Transaction Manager 9560 User Manual

Manual is about: stationary online data collection reader

Summary of Transaction Manager 9560

  • Page 1

    Nugget code39 helconital 9560 transaction manager p/n 059724-005 user’s manual.

  • Page 2

    Nugget code39 helconital intermec corporation 6001 36th avenue west p.O. Box 4280 everett, wa 98203-9280 u.S. Service and technical support: 1-800-755-5505 u.S. Media supplies ordering information: 1-800-227-9947 canadian service and technical support: 1-800-688-7043 canadian media supplies ordering...

  • Page 3

    Nugget code39 helconital iii manual change record this page records changes to the manual. The manual was released at rev. A. Revision date description of change 001 4/93 illustrations in chapters 1 and 2 were revised to reflect the redesigned housing. The mounting plate template was deleted from th...

  • Page 5: Contents

    Contents v contents before you begin xv warranty information xv safety summary xv warnings, cautions, and notes xvi about this manual xvi other intermec manuals xx getting started roadmap 1-3 the 9560 transaction manager 1-4 9560 component options 1-5 optional input devices 1-6 data formats and prog...

  • Page 6: Installing The 9560

    9560 transaction manager user’s manual vi connecting directly to a computer 2-13 connecting to a computer and terminal 2-13 connecting to a port concentrator or system unit 2-14 direct wiring 2-16 multi-drop line wiring 2-16 meeting power supply requirements 2-18 installing the 9560 overview of inst...

  • Page 7

    Contents vii using the keypad 4-11 function key layout 4-12 data communications and operating options introduction to data communications 5-3 data communications in a data collection system 5-3 the iso data communications model 5-3 physical layer 5-4 data link layer 5-4 full-duplex protocols versus ...

  • Page 8: Configuring The 9560

    9560 transaction manager user’s manual viii nonbuffered full-duplex operation 5-18 nonbuffered half-duplex operation 5-18 block terminal operation 5-18 displaying international character sets 5-19 using the katakana character set 5-23 entering katakana characters 5-25 assigning a function key to kat...

  • Page 9

    Contents ix character set 7-9 codabar 7-10 code 11 7-12 code 39 7-13 code 93 7-14 code 128 7-15 computer response required mode (crrm) 7-16 data bits 7-17 display setting 7-18 eom (end of message) 7-19 full ascii 7-20 intercharacter delay 7-21 interface 7-22 interleaved 2 of 5 (i 2 of 5) 7-23 irl ba...

  • Page 10: Data Entry Commands

    9560 transaction manager user’s manual x 2 of 5 (two of five) 7-56 upc/ean 7-57 xoff 7-60 xon 7-61 data entry commands using data entry commands 8-3 entering data entry commands 8-4 backspace 8-5 capacity 8-5 clear 8-6 command 8-7 command override 8-7 default configuration 8-8 delete data 8-9 enable...

  • Page 11: Interactive Reader Language

    Contents xi reset 8-28 resume program 8-28 review 8-29 right host message 8-29 run program 8-30 transmit (no clear) 8-30 transmit file 8-31 interactive reader language introduction to irl 9-3 irl editor 9-4 using the editor 9-4 exiting the irl editor 9-5 creating and running irl programs 9-6 inserti...

  • Page 12: Specifications

    9560 transaction manager user’s manual xii slot scanner does not function... 10-4 reader beeps continually on power up... 10-4 status beeps 10-5 adjusting the beep volume 10-5 communications errors 10-6 host communications failure 10-6 maximum received data 10-6 maximum transmitted data 10-7 specifi...

  • Page 13: Command Summary

    Contents xiii command summary command summary c-3 data entry mode command summary c-4 irl run mode command summary c-6 glossary index c g i.

  • Page 15: Before You Begin

    Nugget nugget code39 code39 helconital f before you begin xv before you begin this section introduces you to standard warranty provisions, safety precautions, warnings and cautions, document formatting conventions, and sources of additional product information. Warranty information to receive a copy...

  • Page 16: About This Manual

    9560 transaction manager user’s guide xvi warnings, cautions, and notes the warnings, cautions, and notes in this manual use the following format. Warning a warning alerts you of an operating procedure, practice, condition, or statement that must be strictly observed to avoid death or serious injury...

  • Page 17

    Nugget nugget code39 code39 helconital f before you begin xvii organization the manual is organized as follows: chapter what you will find 1 getting started a roadmap for installing and using the 9560. 2 preparing to install the 9560 background information on external devices, selecting cabling, and...

  • Page 18

    9560 transaction manager user’s guide xviii terms and conventions the next tables explain the specific terms and formatting conventions used throughout this manual. This term means 9560 the 9560 transaction manager reader the 9560 transaction manager or an intermec programmable bar code reader or ve...

  • Page 19

    Nugget nugget code39 code39 helconital f before you begin xix this convention means ctrl-p keys connected by a dash mean that you are required to press more than one key at the same time. It is important that you press and hold the keys in the order they are listed in the text. For example, ctrl-p m...

  • Page 20: Other Intermec Manuals

    9560 transaction manager user’s guide xx other intermec manuals you may need additional information for working with the 9560 in a data collection system. To order additional manuals, contact your local intermec service supplier. Title intermec part no. System and programming manuals data communicat...

  • Page 21: 9560

    Nugget code39 helconital 9560 7 8 9 4 5 6 1 2 3 - 0 . Bksp space enter d e caps i j $ n o / t , x y z a b c f g h k l m q u v w f1 f6 f2 f7 f3 f8 f4 f9 f5 f10 intermec p r s getting started 1.

  • Page 22

    Nugget code39 helconital.

  • Page 23: Roadmap

    Nugget nugget code39 code39 helconital getting started 1-3 1 this chapter provides a roadmap to installing and using the 9560 transaction manager and provides an overview of the 9560. Roadmap for help with start here getting to know the 9560 read this chapter to learn basic options and components of...

  • Page 24: The 9560 Transaction Manager

    9560 transaction manager user’s manual nugget nugget code39 code39 helconital 1-4 the 9560 transaction manager the intermec 9560 transaction manager is a stationary online data collection reader. It collects data from digital input devices, such as a bar code scanner, and transmits the data to a hos...

  • Page 25: 9560 Component Options

    Nugget nugget code39 code39 helconital getting started 1-5 1 9560 component options the 9560 offers two display options, three keyboard options, and three reader options. Both displays are lcd displays with an led backlight. All keyboards have programmable function keys. You have these basic options...

  • Page 26: Optional Input Devices

    9560 transaction manager user’s manual nugget nugget code39 code39 helconital 1-6 optional input devices the 9560 accepts input from several sources. The basic configuration includes either an internal magnetic card reader or an internal slot scanner. The slot scanner is available in visible or infr...

  • Page 27: Bar Code Symbologies

    Nugget nugget code39 code39 helconital getting started 1-7 1 bar code symbologies the 9560 can automatically discriminate between several bar code symbologies. You can set the reader to decode any combination of the valid symbologies. You can save reader memory by enabling only the symbologies requi...

  • Page 29: 9560

    Nugget code39 helconital 9560 7 8 9 4 5 6 1 2 3 - 0 . Bksp space enter d e caps i j $ n o / t , x y z a b c f g h k l m q u v w f1 f6 f2 f7 f3 f8 f4 f9 f5 f10 intermec p r s preparing to install the 9560 2.

  • Page 30

    Nugget code39 helconital.

  • Page 31

    Preparing to install the 9560 2-3 2 this chapter contains the background information you need before you install the 9560. If you are familiar with the 9560, you may skip this chapter. Getting ready to install the 9560 once you are familiar with the 9560, you are ready to plan your system and how to...

  • Page 32

    9560 transaction manager user’s manual 2-4 determining a mounting location you can mount the 9560 on a horizontal surface, such as a desktop, or on a vertical surface, such as a wall. Make sure that the mounting location provides the following: • easy access to the internal card reader • easy access...

  • Page 33: Selecting External Devices

    Preparing to install the 9560 2-5 2 choosing secured or unsecured wiring before mounting the 9560, you must choose which type of wiring your system requires. Secured wiring protects the cables from exposure and requires you to install the security plate on the 9560. Unsecured wiring routes the cable...

  • Page 34

    9560 transaction manager user’s manual 2-6 for example, if your system has a 9191 satellite wand station and an internal slot scanner, you can only scan from one or the other at one time. The 9560 cannot process information from both scanners at the same time. The internal magnetic card reader does ...

  • Page 35: Using The Sense Inputs

    Preparing to install the 9560 2-7 2 2. Set the 9560 trigger mode to edge and define a scanner timeout. To set these parameters, see chapter 6, “configuring the 9560,” and chapter 7, “configuration commands.” to enable remote triggering with software commands 1. Set the scanner to auto trigger mode. ...

  • Page 36

    9560 transaction manager user’s manual 2-8 the status is stored as follows: • the #0 register contains a 3-digit binary string. • a 1 indicates a signal has been detected; a 0 indicates no signal. • the digits correspond to the inputs as shown in the following diagram: 0 1 1 register #0 first input ...

  • Page 37: Using The Output Relays

    Preparing to install the 9560 2-9 2 using the output relays the 9560 includes three sense inputs and three single-pole, double-throw output relays. You use these relays to actuate external devices, such as door or turnstile locks. Each relay is rated as follows: • 24v (ac or dc) maximum • 1a maximum...

  • Page 38: Cable Interface Requirements

    9560 transaction manager user’s manual 2-10 connecting to a data collection system you can connect the 9560 into a data collection system in one of three ways: • connect to a computer only • connect to a computer and terminal • connect to a port concentrator or system unit with or without a terminal...

  • Page 39

    Preparing to install the 9560 2-11 2 the following cable diagrams and connector pin assignments apply to the three 9560 data collection system choices: • computer • computer and terminal • port concentrator or system control unit with or without a terminal null modem cable diagram and modem connecto...

  • Page 40

    9560 transaction manager user’s manual 2-12 modem cable diagram and terminal connector pin assignments to reader to computer 25 13 1 14 9560-07u the 25-pin modem cable works with an rs-232 interface only. You will need to build a custom cable if you are using rs-422 or rs-485. Use the pin assignment...

  • Page 41

    Preparing to install the 9560 2-13 2 connecting directly to a computer you can connect a computer directly to the 9560 modem connector. If the connector on the computer is a plug (not a socket), then use a socket/socket adapter cable, such as intermec part no. 035009s. The 9560 modem connector is wi...

  • Page 42

    9560 transaction manager user’s manual 2-14 connecting to a computer and terminal computer modem connector crt terminal terminal connector 9560-10u you need a modem cable, such as intermec cable part no. 043237s. You can also use any other modem cable that meets these standards: • 4-wire modem cable...

  • Page 43

    Preparing to install the 9560 2-15 2 connecting the 9560 to a port concentrator port concentrator modem connector modem connector 9560-11u connecting the 9560 to a 9154 line controller modem connector 9154 line controller 9560-12u port concentrator options concentrator protocol interface cable 9161b...

  • Page 44

    9560 transaction manager user’s manual 2-16 direct wiring direct wiring to a port concentrator requires a cable with the following: • one connector that is compatible with the port concentrator • 25-pin, d-subminiature plug connector the modem connector is wired as a data terminal equipment (dte) de...

  • Page 45

    Preparing to install the 9560 2-17 2 intermec recommends using a cable capable of passing the vw-1 vertical flame test. The following table lists belden cables that meet these requirements. Belden cable meeting multi-drop requirements nominal nominal belden part vw-1 test gauge impedance capacitance...

  • Page 46

    9560 transaction manager user’s manual 2-18 meeting power supply requirements the 9560 contains an internal power supply that automatically adjusts to any input from 100 to 240 vac and from 50 to 60 hz. A standard iec connector, located on the chassis and directly below the connector board, accepts ...

  • Page 47: 9560

    Nugget code39 helconital 9560 7 8 9 4 5 6 1 2 3 - 0 . Bksp space enter d e caps i j $ n o / t , x y z a b c f g h k l m q u v w f1 f6 f2 f7 f3 f8 f4 f9 f5 f10 intermec p r s installing the 9560 3.

  • Page 48

    Nugget code39 helconital.

  • Page 49

    Installing the 9560 3-3 3 this chapter contains the installation procedures for the 9560. To properly and safely install the 9560, you must read this entire chapter and understand the installation process. Overview of installing the 9560 before installing the 9560, make sure that you received all th...

  • Page 50

    9560 transaction manager user’s manual 3-4 connector pcb parts and their locations audio connector wand/slot scanner connector terminal blocks laser scanner connector terminal connector modem connector exit irl switch 9560-44u connector pcb battery sense jumper block relays general installation step...

  • Page 51

    Installing the 9560 3-5 3 warning warning when you install the 9560, you must strictly follow the procedures in this manual and any and all local building codes. Failure to comply may result in a hazardous situation. Avertissement il faut réaliser l'installation de la 9560 en suivant strictement les...

  • Page 52: Routing With Secured Wiring

    9560 transaction manager user’s manual 3-6 routing with secured wiring use the following drawing as a guide for routing secured wiring in the 9560. 9560 7 8 9 4 5 6 1 2 3 - 0 . Bksp space enter d e caps i j $ n o / t , x y z a b c f g h k l m q u v w f1 f6 f2 f7 f3 f8 f4 f9 f5 f10 intermec intermec ...

  • Page 53

    Installing the 9560 3-7 3 routing with unsecured wiring use the following drawing as a guide to routing unsecured wiring in the 9560. Mounting surface 9560 7 8 9 4 5 6 1 2 3 - 0 . Bksp space enter d e caps i j $ n o / t , x y z a b c f g h k l m q u v w f1 f6 f2 f7 f3 f8 f4 f9 f5 f10 intermec a litt...

  • Page 54: Connecting External Devices

    9560 transaction manager user’s manual 3-8 connecting external devices external devices, such as scanners, laser wands, crts, and sense input devices, connect to the 9560 pcb connector board. The following drawing shows the connector locations. Audio connector wand/slot scanner connector terminal bl...

  • Page 55: Connecting Input Devices

    Installing the 9560 3-9 3 connecting input devices connect the input device to the connector listed in the following table. Model and description connect to 1260 and 1270 series digital wands wand (modular) connector 1350 series badge scanners wand (modular) connector 1500 and 1600 series laser scan...

  • Page 56

    9560 transaction manager user’s manual 3-10 to connect to sense inputs 1. Determine the required terminal and jumper blocks, and then set the jumpers for the sense inputs. A. Use the following terminal and jumper blocks for each sense input: sense input terminal block jumper block 1 j1 j5 2 j2 j6 3 ...

  • Page 57: Connecting to Output Relays

    Installing the 9560 3-11 3 connecting to output relays you use the output relays to control external devices, such as an electronic door lock. You connect output devices to terminals 1, 2, and 3 of a terminal block. For more information, see “selecting external devices” in chapter 2. Caution power t...

  • Page 58: Connecting Audio Devices

    9560 transaction manager user’s manual 3-12 sample output relay application electric door opener secondary circuit of no more than 24 vdc or vac and no more than 1a. Terminal block 4 5 external 9560 1 2 3 relay 9560-05u connecting audio devices you can connect an external amplifier and speaker or a ...

  • Page 59: Attaching The Mounting Plate

    Installing the 9560 3-13 3 attaching the mounting plate after connecting all cables to the 9560, attach the mounting plate to the housing. Use the following drawing as a guide. Attaching the mounting plate to 9560 housing 9560 7 8 9 4 5 6 1 2 3 - 0 . Bksp space enter d e caps i j $ n o / t , x y z a...

  • Page 60

    9560 transaction manager user’s manual 3-14 routing cables through the sealing foam 9560-32u sealing foam warning warning if you need to remove the 9560 mounting plate, first disconnect power to the unit. Failure to comply could result in injury or death. Avertissement si vous devez enlever la plaqu...

  • Page 61

    Installing the 9560 3-15 3 attaching the 9560 to the wall 1. Hold the 9560 to the wall and mark the three screw locations. 2. Set aside the 9560 and predrill the screw holes. 3. Screw the 9560 to the mounting surface with three screws as shown below. Screw locations for attaching the 9560 to the wal...

  • Page 63: 9560

    Nugget code39 helconital 9560 7 8 9 4 5 6 1 2 3 - 0 . Bksp space enter d e caps i j $ n o / t , x y z a b c f g h k l m q u v w f1 f6 f2 f7 f3 f8 f4 f9 f5 f10 intermec p r s starting and operating the 9560 4.

  • Page 64

    Nugget code39 helconital.

  • Page 65: Starting The 9560

    Operating the 9560 4-3 4 this chapter explains how to start the 9560 and how to use the slot scanner, magnetic card reader, wand, laser scanner, and keypad. Starting the 9560 to start the 9560, you simply plug in the power cord. If the 9560 contains an irl program and the unit is configured to resum...

  • Page 66

    9560 transaction manager user’s manual 4-4 starting the 9560 with the magnetic card reader the magnetic card reader requires the 9560 to have specific host communication settings at power up. If you have not changed the host settings, you will not have a problem. However, if you change the host sett...

  • Page 67: Reading Bar Code Labels

    Operating the 9560 4-5 4 reading bar code labels bar code labels can contain data or commands. Each label must include start and stop characters that provide initial timing references and direction of read information to the coding logic. Intermec printers automatically generate asterisks (*) as the...

  • Page 68: Using The Slot Scanner

    9560 transaction manager user’s manual 4-6 using the slot scanner you can order the 9560 with an internal infrared or visible light slot scanner. The slot scanner is always triggered and available for input. To use the slot scanner, simply slide a bar-coded object (such as an identification badge, e...

  • Page 69

    Operating the 9560 4-7 4 using the magnetic card reader the 9560 requires an irl program to use the magnetic card reader. When you order the 9560 with an internal magnetic card reader, the irl control program is already installed on the unit and on a disk. The magnetic card reader accepts magnetic c...

  • Page 70: Using A Wand

    9560 transaction manager user’s manual 4-8 the irl control program and the magnetic card reader settings are explained in chapter 9, “interactive reader language.” for more information on the magnetic card reader specifications, refer to these publications: • ansi x4.13-1983 specifications for credi...

  • Page 71: Using A Laser Scanner

    Operating the 9560 4-9 4 4. Practice using the wand on the following label. Be sure to hold the wand at a slight angle. Lightly touch the label when scanning. *label* *label* using a laser scanner you can use intermec 1500 and 1600 series laser scanners with the 9560. Refer to the documentation supp...

  • Page 72: Optimum Scanning

    9560 transaction manager user’s manual 4-10 4. For best results, do not scan a label straight on. Aim the scanner as shown. Generally you get the best results with a skew near zero and a pitch near ±20°. 65° pitch (vertical reading angle) skew (horizontal reading angle) 55° *123* ± 2° dead zone wher...

  • Page 73: Using The Keypad

    Operating the 9560 4-11 4 using the keypad the 9560 has three keypad options: • alphanumeric • numeric • numeric ii, large keys 9560 intermec a litton company 9560-46u alphanumeric numeric numeric ii code 128 standard code 128 standard 2x40 1x20

  • Page 74: Function Key Layout

    9560 transaction manager user’s manual 4-12 function key layout each keypad has 10 programmable function keys. The alphanumeric and numeric/function keypads label the keys f1 through f10. Add your own labels or use the labels included with the 9560 for custom key names. The numeric ii keypad with th...

  • Page 75: 9560

    Nugget code39 helconital 9560 7 8 9 4 5 6 1 2 3 - 0 . Bksp space enter d e caps i j $ n o / t , x y z a b c f g h k l m q u v w f1 f6 f2 f7 f3 f8 f4 f9 f5 f10 intermec p r s data communications and operating options 5.

  • Page 76

    Nugget code39 helconital.

  • Page 77

    Data communications and operating options 5-3 5 this chapter provides a general overview of data communications and 9560 operating options, such as display settings. For more details, refer to intermec’s data communications reference manual. Introduction to data communications your bar code equipmen...

  • Page 78: Physical Layer

    9560 transaction manager user’s manual 5-4 physical layer the physical layer describes the hardware components of data transmission. It sets standards for transmitting voltages and electrical pulses through cables, connectors, and components. Data transmission at the physical layer is defined in the...

  • Page 79

    Data communications and operating options 5-5 5 asynchronous protocols at this level perform error detection. For synchronous protocols, this layer detects starting and ending flags and generates a cyclical redundancy check (crc). This layer also identifies whether the transmission channel is dedica...

  • Page 80: Working With Protocols

    9560 transaction manager user’s manual 5-6 the xon or the xoff character may match the lrc (longitudinal redundancy check character). If so, the lrc is never checked for transparency. It is always treated as a parameter. Received data is also checked for a dle. The xon or xoff character is interpret...

  • Page 81: Polling Mode D Protocol

    Data communications and operating options 5-7 5 point-to-point accepts and then transmits all data to the host when either: • the reader receives the eom character. • the timeout delay limit is reached. Polling mode d protocol polling mode d protocol is a proprietary intermec block transfer protocol...

  • Page 82

    9560 transaction manager user’s manual 5-8 user-defined and user-defined multi-drop protocols you define all protocol parameters in user-defined protocols. Thus, you can duplicate any protocol to emulate a proprietary or irregular protocol on a host computer. Some protocols are very robust and secur...

  • Page 83: Buffering Received Data

    Data communications and operating options 5-9 5 6. If the req is enabled, also enable the res. When the req is enabled, the reader waits for the timeout period to expire and then accepts the data. By enabling the res, the host sends the res when it recognizes the response (aff) sent by the reader if...

  • Page 84: Data Format Requirements

    9560 transaction manager user’s manual 5-10 data format requirements regardless of the protocol you selected, the host and the reader must format the data before transmitting it. Each transmission includes a start character, the data block, and an end character. The som (start of message) character ...

  • Page 85: Eof Characters (End of File)

    Data communications and operating options 5-11 5 • the eof (end of file) is only transmitted after the last record of a file. • time is never appended to the transmitted files. Preambles and the postamble are described more completely in chapter 8, “data entry commands.” eor characters (end of recor...

  • Page 86: Error Checking

    9560 transaction manager user’s manual 5-12 eom characters (end of message) the eom character follows the data and indicates the end of a data block. The eom character is a protocol character and is not part of the data format. The 9560 can transmit one or two eom characters. If you use nul for the ...

  • Page 87

    Data communications and operating options 5-13 5 reader warning messages all error or warning messages to the operator. These messages can interrupt the current display at any time and are generally accompanied by a beep. If transparent display is selected, the error messages are not displayed. Disp...

  • Page 88: Display Overflow

    9560 transaction manager user’s manual 5-14 description code action cursor position esc[#;#h moves the cursor to the position specified by the # parameters. The first parameter specifies the row or line number and the second parameter specifies the column number. If zero or no parameter is entered, ...

  • Page 89

    Data communications and operating options 5-15 5 use these commands to modify the virtual display: command result review moves the display up one row in the current virtual display image if a display control sequence was executed. Forward moves the display image down one row in the current virtual d...

  • Page 90: Buffered Terminal Operation

    9560 transaction manager user’s manual 5-16 this table lists valid reader settings for the terminal and reader. Terminal screen formatting reader setting protocol choices reader formats terminal screen buffered point-to-point user-defined user-defined multi-drop polling mode d multi-drop host format...

  • Page 91

    Data communications and operating options 5-17 5 if a host message interrupts a data transmission, the reader: 1. Sends a carriage return line feed (cr lf) to the terminal 2. Displays the host message on the terminal 3. Sends a cr lf to the terminal 4. Displays the entire contents of the preamble an...

  • Page 92: Block Terminal Operation

    9560 transaction manager user’s manual 5-18 nonbuffered full-duplex operation in nonbuffered, full-duplex operation, the reader does not buffer, format, or display the data. The reader sends all terminal port input out the modem port as the data is received. The host echoes all received data, and fo...

  • Page 93

    Data communications and operating options 5-19 5 you must set the host for half-duplex operation. The reader does not format messages from the host, but displays host messages directly on the terminal screen. Although you can configure the terminal in full-duplex, intermec does not recommend it. Use...

  • Page 94

    9560 transaction manager user’s manual 5-20 us-ascii and western european character sets country 23 40 5b 5c 5d 5e 60 7b 7c 7d 7e united states england germany denmark france sweden italy spain 9560-50u all other characters in the ascii chart remain as defined in the us ascii chart on the following ...

  • Page 95

    Data communications and operating options 5-21 5 ascii chart binary 0 hex 1 dec 2 c39 3 char 4 binary 0 hex 1 dec 2 c39 3 char 4 00000000 00 00 %u nul 00100000 20 32 sp sp 5 00000001 01 01 $a soh 00100001 21 33 /a ! 00000010 02 02 $b stx 00100010 22 34 /b " 00000011 03 03 $c etx 00100011 23 35 /c # ...

  • Page 96

    9560 transaction manager user’s manual 5-22 ascii chart (continued) binary 0 hex 1 dec 2 c39 3 char 4 binary 0 hex 1 dec 2 c39 3 char 4 01000000 40 64 %v @ 01100100 64 100 +d d 01000001 41 65 a a 01100101 65 101 +e e 01000010 42 66 b b 01100110 66 102 +f f 01000011 43 67 c c 01100111 67 103 +g g 010...

  • Page 97

    Data communications and operating options 5-23 5 ascii control characters control character definitions control character definitions nul null, or all zeros dc1 device control 1 (xon) soh start of heading dc2 device control 2 stx start of text dc3 device control 3 (xoff) etx end of text dc4 device c...

  • Page 98

    9560 transaction manager user’s manual 5-24 japanese katakana character set 2 3 a b c d 0 1 2 3 4 5 6 7 8 9 a b c d e f hex code note 1 note 1 9560-51u note: character fd is not supported in this version of the 9560. Note : enter the yen sign, ¥, as alt-@ or 5c hex..

  • Page 99: Entering Katakana Characters

    Data communications and operating options 5-25 5 entering katakana characters you can enter katakana characters in two different ways: you can use keyboard mapping, and you can type in ro-maji: • keyboard mapping (kana entry style) maps the katakana characters to specific keys on your 1700 keyboard....

  • Page 100: Character Sets

    9560 transaction manager user’s manual 5-26 assigning a function key to katakana and us-ascii character sets you can assign one function key to toggle between us-ascii and katakana, or you can assign a different function key to select each character set. The function keys you assign work only when t...

  • Page 101

    Data communications and operating options 5-27 5 katakana characters in roman alphabetical order key key alt+key alt+key a q a ku-ten a “ 3 del b , b hajime- kakko b ! 4 r c s c owari- kakko c k 5 p d t d doku-ten d > 6 daku-ten e u e chyu-ten e $ 7 l f v f f % 8 n g w g » g ? 9 ~ h x h ¼ h : i y i ...

  • Page 103

    Data communications and operating options 5-29 5 special katakana characters in japanese alphabetical order cho-on alt+u ku-ten a chu-ten alt+l hajime-kakko b ¥ alt+n owari-kakko c daku-ten alt+6 doku-ten d chyu-ten e ro-maji mode character table the following table shows the ro-maji spelling for ea...

  • Page 104

    9560 transaction manager user’s manual 5-30 ro-maji spelling for katakana characters (continued) daku on characters ° - ¦ ¡ ba da za ga ± ¬ § ¢ bi di zi/ji gi ² ¨ « bu du zu gu ³ ® © ¤ be de ze ge ´ ¯ ª ¥ bo do zo go handaku on characters lowercase katakana characters µ Á » pa xya xa ¶ ¼ pi xi · ½ /...

  • Page 105: Accumulate Mode

    Data communications and operating options 5-31 5 9560 operating modes and command types the 9560 has three basic operating modes: • data entry mode, which includes accumulate and full ascii modes • configuration mode • irl editor mode data entry mode by default, the reader is in data entry mode, wai...

  • Page 106: Full Ascii Mode

    9560 transaction manager user’s manual 5-32 full ascii mode full ascii mode is a part of data entry mode that you use to enter or transmit ascii control characters or lowercase characters as data. When the reader is in full ascii mode, it decodes alphanumeric characters as ascii characters. For exam...

  • Page 107: 9560

    Nugget code39 helconital 9560 7 8 9 4 5 6 1 2 3 - 0 . Bksp space enter d e caps i j $ n o / t , x y z a b c f g h k l m q u v w f1 f6 f2 f7 f3 f8 f4 f9 f5 f10 intermec p r s configuring the 9560 6.

  • Page 108

    Nugget code39 helconital.

  • Page 109

    Configuring the 9560 6-3 6 this chapter explains how to configure the 9560 to work in your system. Specifying configuration parameters before you use the 9560 with your system, you must specify these configuration parameters: • bar code symbologies • reader operating parameters • communications prot...

  • Page 110

    9560 transaction manager user’s manual 6-4 note : you do not need to reconfigure the 9560 after a power failure. The 9560 saves your selected parameters in nonvolatile memory. Note : the 9560 keypad does not contain a ctrl key. To enter a command requiring the ctrl key, scan a bar code or use a 1700...

  • Page 111

    Configuring the 9560 6-5 6 operating parameters configuration settings parameter options beep volume 0 (softest) 8 (lower volume) 3 (medium) 9 (raise volume) 7 (loudest) display mode buffered transparent character set us-ascii danish katakana (japanese) french swedish german italian united kingdom s...

  • Page 112

    9560 transaction manager user’s manual 6-6 communications protocol configuration settings point-to-point parameters options point-to-point (default protocol) interface rs-232 rs-422/rs-485 terminal setting buffered, block transparent nonbuffered full-duplex nonbuffered half-duplex xon/xoff nul/nul a...

  • Page 113

    Configuring the 9560 6-7 6 communications protocol configuration settings (continued) multi-drop parameters options interface rs-222/rs485 address character a a to z, 0 to 5 terminal setting buffered transparent xon/xoff nul/nul any ascii character baud rate 2400 4800 9600 19200 parity even odd disa...

  • Page 114

    9560 transaction manager user’s manual 6-8 user-defined and user-defined multi-drop protocol configuration settings parameters options interface rs-232 rs-422/rs-485 multi-drop default terminal setting buffered, block transparent nonbuffered full-duplex nonbuffered half-duplex xon/xoff nul/nul any a...

  • Page 115

    Configuring the 9560 6-9 6 user-defined and user-defined multi-drop protocol configuration settings (continued) run dc2 end so pss cr pak rs bak bel default settings are in bold text. Note : for user-defined multi-drop protocol, the interface default is rs-422/rs485..

  • Page 116: Using Batch Configuration

    9560 transaction manager user’s manual 6-10 using batch configuration to configure several readers identically, you can print a bar code “menu” with several parameters per label. A label can contain up to 48 characters, but this many characters may not scan easily. Each label should include the foll...

  • Page 117: Download Command Example

    Configuring the 9560 6-11 6 downloading configuration commands you can download any configuration command from a host computer. You can combine commands into a single downloaded string of up to 254 characters. The string must use the host communication protocol currently in effect. Each command stri...

  • Page 118

    9560 transaction manager user’s manual 6-12 using prompting configuration mode in prompting configuration, the 9560 prompts you step by step through all configuration tasks. The reader displays a prompt for each option within each parameter, beginning with the current setting. You can change each se...

  • Page 119

    Configuring the 9560 6-13 6 moving around in prompting configuration mode you can move through all the parameters of a particular task or move through the options within each parameter. To move through prompting configuration mode 1. Decide which task to perform: select bar codes, set operating para...

  • Page 120

    9560 transaction manager user’s manual 6-14 finding help in prompting configuration mode you can use the help command anytime in prompting configuration. When you type the question mark ? , the 9560 displays the commands that prompting configuration recognizes, one screen at a time. To enter help, p...

  • Page 121

    Configuring the 9560 6-15 6 select codes no 3. Press space. The 9560 displays this prompt: select codes yes 4. Press enter to begin changing bar code settings. The 9560 displays this prompt: code 39 no ck digit 5. Press enter until this prompt is displayed: code 93 enable 6. Press space. The prompt ...

  • Page 122: Standard Display Prompts

    9560 transaction manager user’s manual 6-16 standard display prompts the following table lists the configuration prompts and options for the standard 2x40 character display. The options are the same for each display, but the prompts are different. The prompts are listed in the order they appear. Con...

  • Page 123

    Configuring the 9560 6-17 6 configuration prompts for 2x40 standard display (continued) code 128 standard standard ucc-128 disabled aaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaa a aaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaa a aaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaa op parameters no no yes se...

  • Page 124

    9560 transaction manager user’s manual 6-18 configuration prompts for 2x40 standard display (continued) interface rs232 rs232 rs422/485 terminal mode non buffered fd non buffered fd buffered transparent non buffered hd block xon = nul nul any ascii character xoff = nul nul any ascii character baud r...

  • Page 125

    Configuring the 9560 6-19 6 configuration prompts for 2x40 standard display (continued) interchar delay 0 msec 0 msec 1 msec 2 msec 5 msec 10 msec 20 msec 50 msec 100 msec lrc disabled disabled enabled pol = nul nul any ascii character sel = nul nul any ascii character res = nul nul any ascii charac...

  • Page 126

    9560 transaction manager user’s manual 6-20 configuration prompts for 2x40 standard display (continued) eop = syn syn any ascii character run = dc2 dc2 any ascii character end = so so any ascii character pss = cr cr any ascii character pak = rs rs any ascii character bak = bel bel any ascii characte...

  • Page 127: Large-Type Display Prompts

    Configuring the 9560 6-21 6 large-type display prompts this table lists the configuration prompts and options for the large-type 1x20 character display. The options are the same for the standard and large-type displays, but the prompts are shorter for the large-type display. The prompts are listed i...

  • Page 128

    9560 transaction manager user’s manual 6-22 configuration prompts for 1x20 display (continued) code 11 1 ck digit 1 ck digit 2 ck digit disable code 93 enable enable disable code 128 standard standard ucc-128 disable aaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaa a aaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaa a aaa...

  • Page 129

    Configuring the 9560 6-23 6 configuration prompts for 1x20 display (continued) protocol user def user def pt to pt polling d multi-drop user mdrop the following options are displayed if needed for the protocol you choose here. Interface rs232 rs232 rs422/485 term non buffer fd non buffer fd buffered...

  • Page 130

    9560 transaction manager user’s manual 6-24 configuration prompts for 1x20 display (continued) intrchar dly 0 ms 0 msec 1 msec 2 msec 5 msec 10 msec 20 msec 50 msec 100 msec lrc disable disable enable pol = nul nul any ascii character sel = nul nul any ascii character res = nul nul any ascii charact...

  • Page 131

    Configuring the 9560 6-25 6 configuration prompts for 1x20 display (continued) eop = syn syn any ascii character run = dc2 dc2 any ascii character end = so so any ascii character pss = cr cr any ascii character pak = rs rs any ascii character bak = bel bel any ascii character.

  • Page 133: 9560

    9560 7 8 9 4 5 6 1 2 3 - 0 . Bksp space enter d e caps i j $ n o / t , x y z a b c f g h k l m q u v w f1 f6 f2 f7 f3 f8 f4 f9 f5 f10 intermec p r s configuration commands 7.

  • Page 135

    Configuration commands 7-3 7 this chapter provides an alphabetical listing and description of all configuration commands the 9560 recognizes. Using the configuration commands this chapter provides the following information on each configuration command: • description of the command • syntax for send...

  • Page 136: Addr (Address, Multidrop)

    Configuration commands - addr (address, multidrop) 7-4 addr (address, multidrop) purpose: defines the address of the communication port when using a mutli-drop protocol. Each address has unique pol and sel characters, which are automatically set when the address is configured. Default: a syntax: hc ...

  • Page 137

    Configuration commands - aff (affirmative acknowledgment) 7-5 7 aff (affirmative acknowledgment) purpose: enables or disables the handshake event that is an affirmative acknowledgment to a message. Aff and neg must both be enabled. Default: nul (disabled) syntax: pg data acceptable values for data a...

  • Page 138: Append Time to Data

    Configuration commands - append time to data 7-6 append time to data purpose: determines if the time is added after the data for transmission. Default: not appended syntax: de data acceptable values for data are: 0 time not appended 1 time appended scan: scan one of these labels: disable append time...

  • Page 139: Baud Rate

    Configuration commands - baud rate 7-7 7 baud rate purpose: defines the data transfer speed. It must match the baud rate of the device (host) that the reader is communicating with. For polling mode d, the baud rate must be 1200 or higher. For multi-drop protocol, the baud rate must be 2400 or higher...

  • Page 140: Beeper Volume

    Configuration commands - beeper volume 7-8 beeper volume purpose: adjusts the volume of beeps from the reader. Set the beep volume according to your preference and work environment. Default: loudest level syntax: bv data acceptable values for data are: 0 to 9, where: 0 softest level 3 medium level 7...

  • Page 141: Character Set

    Configuration commands - character set 7-9 7 character set purpose: determines the language used to display characters. Default: us ascii syntax: dx data acceptable values for data are: 0 us ascii 1 french 2 german 3 united kingdom 4 danish 5 swedish 6 italian 7 spanish 8 japanese katakana scan: sca...

  • Page 142: Codabar

    Configuration commands - codabar 7-10 codabar purpose: enables or disables decoding of codabar symbology. Default: standard with abcd start/stop characters syntax: cd data data must be 2 digits. Acceptable values are: first digit: 0 disabled 1 abc 2 standard 3 concatenated second digit: 0 no start/s...

  • Page 143

    Configuration commands - codabar 7-11 7 or: to use codabar standard, scan one of these labels: standard, no start/stop standard, dc1-dc4 start/stop *$+cd20$-* *$+cd22$-* *$+cd20$-* *$+cd22$-* standard, abcd start/stop *$+cd21$-* *$+cd21$-* or: to use codabar concatenated, scan one of these labels: c...

  • Page 144: Code 11

    Configuration commands - code 11 7-12 code 11 purpose: enables or disables decoding of code 11 symbology. Default: enabled with one check digit syntax: cg data acceptable values for data are: 0 disabled 1 one check digit 2 two check digits scan: scan one of these labels: disable code 11 2 check digi...

  • Page 145: Code 39

    Configuration commands - code 39 7-13 7 code 39 purpose: enables or disables the coding of code 39 symbology. Default: enabled, no check digit syntax: cb data data must be 2 digits. Acceptable values are: first digit: 0 disabled 1 enabled, no check digit 2 enabled, with check digit 3 hibc second dig...

  • Page 146: Code 93

    Configuration commands - code 93 7-14 code 93 purpose: enables or disables decoding of code 93 symbology. Default: enabled syntax: cf data acceptable values for data are: 0 disabled 1 enabled scan: one of these labels: disable code 93 enable code 93 *$+cf0$-* *$+cf1$-* *$+cf0$-* *$+cf1$-*.

  • Page 147: Code 128

    Configuration commands - code 128 7-15 7 code 128 purpose: enables or disables decoding of code 128 symbology default: enabled syntax: ch data acceptable values for data are: 0 disabled 1 standard 2 enable ucc-128 (decodes ucc-128 enhancements if present) scan: scan one of these labels: disable code...

  • Page 148

    Configuration commands - computer response required mode (crrm) 7-16 computer response required mode (crrm) purpose: determines if the reader requires a response from the host before the reader accepts any more data. Default: disabled syntax: pb data acceptable values for data are: 0 disabled 1 enab...

  • Page 149: Data Bits

    Configuration commands - data bits 7-17 7 data bits purpose: sets the number of data bits the reader uses when communicating with another device. Default: 7 syntax: ii data acceptable values for data are: 7 7 data bits 8 8 data bits scan: scan one of these labels: 7 data bits 8 data bits *$+ii7$-* *...

  • Page 150: Display Setting

    Configuration commands - display setting 7-18 display setting purpose: determines how the reader displays and formats data. Default: buffered syntax: od data acceptable values for data are: 0 buffered 1 transparent scan: scan one of these labels: buffered transparent *$+od0$-* *$+od1$-* *$+od0$-* *$...

  • Page 151: Eom (End of Message)

    Configuration commands - eom (end of message) 7-19 7 eom (end of message) purpose: defines the eom character that is attached to the end of a data block to indicate the end of data transmission to and from the reader. The transmit and receive eom can be defined together or separately. Default: cr lf...

  • Page 152: Full Ascii

    Configuration commands - full ascii 7-20 full ascii purpose: allows the reader to accept ascii characters as data or commands. Default: disabled syntax: rb data acceptable values for data are: 0 disabled 1 enabled scan: scan one of these labels: disable full ascii enable full ascii *$+rb0$-* *$+rb1$...

  • Page 153: Intercharacter Delay

    Configuration commands - intercharacter delay 7-21 7 intercharacter delay purpose: defines the length of time the reader waits before sending each character to the host. It modifies outgoing data only by slowing the transmission speed. A character delay can be useful when your a communicating throug...

  • Page 154: Interface

    Configuration commands - interface 7-22 interface purpose: defines the communications interface. Default: rs-232 syntax: ik data acceptable values for data are: 0 rs-232 1 rs-422/rs-485 scan: scan one of these labels: rs-232 rs-422/485 *$+ik0$-* *$+ik1$-* *$+ik0$-* *$+ik1$-*.

  • Page 155

    Configuration commands - interleaved 2 of 5 (i 2 of 5) 7-23 7 interleaved 2 of 5 (i 2 of 5) purpose: enables or disables decoding of interleaved 2 of 5 symbology. Enabling i 2 of 5 automatically disables 2 of 5. Default: variable length syntax: ca data acceptable values for data are: 0 disabled 2-32...

  • Page 156

    Configuration commands - irl bak (bad program acknowledge) 7-24 irl bak (bad program acknowledge) purpose: character sent by the reader to the host to indicate that an irl program cannot be successfully downloaded. Default: bel syntax: zb data acceptable values for data are: any ascii character nul ...

  • Page 157: Irl End (End of Program)

    Configuration commands - irl end (end of program) 7-25 7 irl end (end of program) purpose: indicates the last block of an irl program when downloading to the reader. Default: so (shift out) syntax: xd data acceptable values for data are: any ascii character nul = disable scan: to disable end, scan t...

  • Page 158: Irl Eof (End of File)

    Configuration commands - irl eof (end of file) 7-26 irl eof (end of file) purpose: indicates the end of an irl program file when downloading an irl program to the reader. Default: nul (disabled) syntax: fa data acceptable values for data are: any ascii character nul = disable scan: to disable eof, s...

  • Page 159

    Configuration commands - irl eop (end of program block) 7-27 7 irl eop (end of program block) purpose: indicates the end of an irl program block when downloading from the host to the reader. Default: syn (synchronous idle) syntax: xb data acceptable values for data are: any ascii character nul = dis...

  • Page 160: Irl Eor (End of Record)

    Configuration commands - irl eor (end of record) 7-28 irl eor (end of record) purpose: indicates the end of an irl program record (block) when downloading an irl program to the reader. Default: nul nul (disabled) syntax: fb data acceptable values for data are: any two ascii characters nul nul = disa...

  • Page 161

    Configuration commands - irl pak (program acknowledge) 7-29 7 irl pak (program acknowledge) purpose: character sent by the reader to the host to acknowledge receiving an irl program. Default: rs (record separator) syntax: za data acceptable values for data are: any ascii character nul = disable scan...

  • Page 162

    Configuration commands - irl pss (program statement separator) 7-30 irl pss (program statement separator) purpose: indicates the separation character for irl program statements. Do not define pss as the same character used for eom. Default: cr (carriage return) syntax: xe data acceptable values for ...

  • Page 163: Irl Run

    Configuration commands - irl run 7-31 7 irl run purpose: indicates the end of an irl program block when downloading from the host to the reader. Default: dc2 syntax: xc data acceptable values for data are: any ascii character nul = disable scan: to disable run, scan this label: disable run *$+xc%u$-...

  • Page 164

    Configuration commands - irl sop (start of program block) 7-32 irl sop (start of program block) purpose: indicates the beginning of an irl program download from the host to the reader. Default: si (shift in) syntax: xa data acceptable values for data are: any ascii character nul = disable scan: to d...

  • Page 165: Katakana

    Configuration commands - katakana 7-33 7 katakana purpose: sets the displayed character set to katakana. You need to specify the entry style (kana or ro-maji) and assign function keys to switch between us ascii and katakana. See “using the katakana character set” in chapter 5 for more information. D...

  • Page 166

    Configuration commands - katakana 7-34 2. Optional. To set the us function key, scan one of these labels: us ascii key f1 us ascii key f6 *$+lb1$-* *$+lb6$-* *$+lb1$-* *$+lb6$-* us ascii key f2 us ascii key f7 *$+lb2$-* *$+lb7$-* *$+lb2$-* *$+lb7$-* us ascii key f3 us ascii key f8 *$+lb3$-* *$+lb8$-...

  • Page 167

    Configuration commands - katakana 7-35 7 katakana key f4 katakana key f9 *$+lc4$-* *$+lc9$-* *$+lc4$-* *$+lc9$-* katakana key f5 *$+lc5$-* *$+lc5$-* note: when the function key for us ascii and katakana are the same key, pressing the function key toggles between the two character sets. By default, f...

  • Page 168

    Configuration commands - lrc (longitudinal redundancy check) 7-36 lrc (longitudinal redundancy check) purpose: the longitudinal redundancy check character is an error checking character that you can append to transmitted and received blocks of data. The host software must support lrc. Default: disab...

  • Page 169

    Configuration commands - neg (negative acknowledgment) 7-37 7 neg (negative acknowledgment) purpose: indicates a negative acknowledgment to a transmitted message. Neg and aff must both be defined. Default: nul (disabled) syntax: ph data acceptable values for data are: any ascii character nul = disab...

  • Page 170: Parity

    Configuration commands - parity 7-38 parity purpose: sets the error checking for data transmissions. Default: even syntax: ib data acceptable values for data are: 0 disabled 1 even 2 odd scan: scan one of these labels: disabled odd *$+ib0$-* *$+ib2$-* *$+ib0$-* *$+ib2$-* even *$+ib1$-* *$+ib1$-* or:...

  • Page 171: Pol (Poll)

    Configuration commands - pol (poll) 7-39 7 pol (poll) purpose: solicits or requests data from a polled device. Default: nul (disabled) syntax: hb data acceptable value for data is: any ascii character scan: to disable pol, scan this label: disable pol *$+hb%u$-* *$+hb%u$ - * or: to set pol to an asc...

  • Page 172: Preamble A Required

    Configuration commands - preamble a required 7-40 preamble a required purpose: adds the preamble characters to the beginning of the data before transmitting the data. Default: not required syntax: oa data acceptable values for data are: 0 not required 1 required scan: scan one of these labels: not r...

  • Page 173: Protocol

    Configuration commands - protocol 7-41 7 protocol purpose: determines how the reader communicates with the host through the dte interface. Default: point-to-point syntax: pa data acceptable values for data are: 0 user-defined 1 point-to-point 2 polling mode d 3 multi-drop 4 user-defined multi-drop s...

  • Page 174: Records Per Block

    Configuration commands - records per block 7-42 records per block purpose: defines the maximum number of data records transmitted per block of data. Usually files are transmitted record by record. You must select the communications protocol before setting the parameters that define the protocol. Def...

  • Page 175

    Configuration commands - req (request for acknowledgment) 7-43 7 req (request for acknowledgment) purpose: enables or disables a request for a repeat handshake event. If req is enabled, aff and neg must also be enabled. Default: disabled syntax: pd data acceptable values for data are: any ascii char...

  • Page 176: Res (Reset)

    Configuration commands - res (reset) 7-44 res (reset) purpose: enables or disables a reset event. Default: nul (disabled) syntax: pc data acceptable value for data is: any ascii character nul = disable scan: to disable res, scan this label: disable res *$+pc%u$-* *$+pc%u$ - * or: to set res to an as...

  • Page 177: Resume Irl

    Configuration commands - resume irl 7-45 7 resume irl purpose: sets the scanner to resume an interrupted irl program at power up. If the program was completed, it starts at the beginning. Default: 0 (disabled) syntax: xg data acceptable values for data are: 0 disabled 1 enabled scan: scan one of the...

  • Page 178: Scanner Timeout

    Configuration commands - scanner timeout 7-46 scanner timeout purpose: defines the maximum length of time the scanner stays on after the trigger is pulled or after a label is passed through the slot. Default: no timeout syntax: sa data or ih data acceptable values for data are: 0 no timeout 1 - 60 1...

  • Page 179: Scanner Operation

    Configuration commands - scanner operation 7-47 7 scanner operation purpose: defines how the scanner operates when the trigger is pulled. One-shot mode requires you to pull the trigger each time you want to scan a bar code. The scanner turns off once it scans the bar code. Automatic mode allows you ...

  • Page 180: Sel (Select)

    Configuration commands - sel (select) 7-48 sel (select) purpose: defines the character that requests permission for the controller to send data to the polled device. Default: nul (disabled) syntax: ha data acceptable value for data is: any ascii character scan: to disable sel, scan this label: disab...

  • Page 181: Select Terminal Mode

    Configuration commands - select terminal mode 7-49 7 select terminal mode purpose: determines the operating mode for connecting to a terminal. Default: nonbuffered full-duplex syntax: oc data acceptable values for data are: 0 nonbuffered (full-duplex) 1 buffered 2 transparent 3 nonbuffered (half-dup...

  • Page 182: Som (Start of Message)

    Configuration commands - som (start of message) 7-50 som (start of message) purpose: defines the first character in a message sent to or received from the host. Default: nul (disabled) syntax: pe data acceptable values for data are: any ascii character nul = disable scan: to disable som, scan this l...

  • Page 183: Stop Bits

    Configuration commands - stop bits 7-51 7 stop bits purpose: sets the number of stop bits. Default: 1 stop bit syntax: ic data acceptable values for data are: 1 1 stop bit 2 2 stop bits scan: scan one of these labels: 1 stop bit 2 stop bits *$+ic1$-* *$+ic2$-* *$+ic1$-* *$+ic2$-*.

  • Page 184: Trigger Event

    Configuration commands - trigger event 7-52 trigger event purpose: defines the triggering method for the scanner. In level triggering, the laser comes on when you pull the trigger and stays on until you release the trigger. In edge triggering, the laser comes on when you pull the trigger and stays o...

  • Page 185: Time In Seconds

    Configuration commands - time in seconds 7-53 7 time in seconds purpose: determines if time is measured in seconds. Default: disabled syntax: da data acceptable values for data are: 0 disabled 1 enabled scan: scan one of these labels: disabled enabled *$+da0$-* *$+da1$-* *$+da0$-* *$+da1$-*.

  • Page 186: Timeout Delay

    Configuration commands - timeout delay 7-54 timeout delay purpose: defines the length of time the reader waits between characters when receiving a message. When the timeout is reached, an error occurs. Default: 10 sec syntax: ie data acceptable values for data are: 0 5 msec 4 10 sec 1 100 msec 5 20 ...

  • Page 187: Turnaround Delay

    Configuration commands - turnaround delay 7-55 7 turnaround delay purpose: defines the length of time the reader waits to respond after receiving data from the host. Default: 0 msec syntax: ig data acceptable values for data are: 0 0 msec 1 1 msec 2 2 msec 3 5 msec 4 10 msec 5 20 msec 6 50 msec 7 10...

  • Page 188: 2 Of 5 (Two of Five)

    Configuration commands - 2 of 5 (two of five) 7-56 2 of 5 (two of five) purpose: enables or disables decoding of 2 of 5 symbology. If interleaved 2 of 5 is enabled, 2 of 5 is disabled. Default: disabled syntax: cc data data must be 3 digits. Acceptable values are: first digit: 0 3 bar start/stop 1 2...

  • Page 189: Upc/ean

    Configuration commands - upc/ean 7-57 7 upc/ean purpose: enables or disables decoding of upc/ean symbologies. Default: upc a/ean-13 enabled, upc e enabled, supplementals enabled syntax: ce data data must be 4 digits. Acceptable values are: first digit 0 upc a/ean-13 disabled 1 upc a/ean-13 enabled 2...

  • Page 190

    Configuration commands - upc/ean 7-58 or: to enable specific upc/ean versions: 1. Scan this label: set upc/ean *+/$+ce* *+/$+ce* 2. Scan one of these labels for the first digit: disable upc a/ean 13 enable upc a/ean 13 * 0* * 1* * 0* * 1* enable upc-a only * 2* * 2* 3. Scan one of these labels for t...

  • Page 191

    Configuration commands - upc/ean 7-59 7 6. Scan this label: exit configuration, save settings *$-* *$ - *.

  • Page 192: Xoff

    Configuration commands - xoff 7-60 xoff purpose: defines the xoff character for controlling handshake events. Default: nul (disabled) syntax: pl data acceptable values for data are: any ascii character nul = disable scan: to disable xoff, scan this label: disable xoff *$+pl%u$-* *$+pl%u$ - * or: to ...

  • Page 193: Xon

    Configuration commands - xon 7-61 7 xon purpose: defines the xon character for controlling handshake events. When xon is disabled, the receive timeout is also disabled. Default: nul (disabled) syntax: pk data acceptable values for data are: any ascii character nul = disable scan: to disable xon, sca...

  • Page 195: 9560

    Nugget code39 helconital 9560 7 8 9 4 5 6 1 2 3 - 0 . Bksp space enter d e caps i j $ n o / t , x y z a b c f g h k l m q u v w f1 f6 f2 f7 f3 f8 f4 f9 f5 f10 intermec p r s data entry commands 8.

  • Page 196

    Nugget code39 helconital.

  • Page 197: Using Data Entry Commands

    Data entry commands 8-3 8 this chapter provides an alphabetical listing and description of all commands the 9560 recognizes in data entry mode. Using data entry commands you use data entry commands to tell the reader to take a specific immediate action, such as clearing the data buffer or temporaril...

  • Page 198: Entering Data Entry Commands

    9560 transaction manager user’s manual 8-4 entering data entry commands you enter data commands in three ways: • typing commands or control codes from a 1700 keyboard or terminal. To enter a command as data, precede the command with the dle character, ctrl p . • downloading data from the host comput...

  • Page 199: Backspace

    Data entry commands - backspace 8-5 8 backspace purpose: deletes one character in the current record. If the reader is in buffered terminal mode, the reader sends a backspace-space-backspace to the terminal. If the buffer is empty, the reader sounds three low beeps. Terminal / keyboard bs or bksp or...

  • Page 200: Clear

    Data entry commands - clear 8-6 clear purpose: clears the current record in the buffer. If the reader is in buffered terminal mode, the reader sends as many backspace–space–backspace strings as necessary to clear the record on the screen. Also clears the preamble/postamble buffer if preamble/postamb...

  • Page 201: Command

    Data entry commands - command 8-7 8 command purpose: searches the data record for commands and full ascii characters. You can build up commands and ascii characters from the ascii chart in appendix b, “full ascii chart.” if no data has been entered in the buffer, this command is combined with the ne...

  • Page 202: Default Configuration

    Data entry commands - default configuration 8-8 default configuration purpose: sets the reader to the factory default configuration. All data entry commands (including any irl programs) entered before executing the default configuration command are lost. Terminal: not applicable host: . + scan: defa...

  • Page 203: Delete Data

    Data entry commands - delete data 8-9 8 delete data purpose: either deletes the data portion of a file without deleting the entire file, or else deletes the entire file. Terminal: not applicable keyboard: ctrl enter c data host: .$ data scan: 1. Scan this label: delete data *.$* *.$* 2. Scan data fr...

  • Page 204: Enable Clock

    Data entry commands - enable clock 8-10 enable clock purpose: sets the real time clock. Format: yy/mm/dd:hh:mm mm/dd:hh:mm dd:hh:mm hh:mm mm if data does not match one of these formats, the reader sounds an error beep and ignores the command. If you omit data , the display prompts you for each clock...

  • Page 205: Enter Accumulate

    Data entry commands - enter accumulate 8-11 8 enter accumulate purpose: all labels decoded after this command are added to the current data buffer until the contents of the buffer are transmitted. If the record count exceeds 128 characters, the reader sounds three low beeps and rejects the last labe...

  • Page 206: Enter Configuration Mode

    Data entry commands - enter computer response required mode (crrm) 8-12 enter computer response required mode (crrm) purpose: waits for a host response after a transmission before allowing more input. This data entry command overrides the configuration command setting until you scan the exit crrm la...

  • Page 207: Enter Display Editor

    Data entry commands - enter display editor 8-13 8 enter display editor purpose: toggles the irl editor between displaying on the 9560 display and displaying on the terminal display. Terminal: not applicable keyboard: ctrl i host: $$ scan: enter display editor *$$* *$$* enter full ascii mode purpose:...

  • Page 208: Enter Irl Editor

    Data entry commands - enter irl editor 8-14 enter irl editor purpose: enters the irl editor. You can toggle between displaying the editor on the 9560 display and the terminal display by sending this command again. Terminal: ctrl i keyboard: not applicable host: $$ scan: enter irl editor *$$* *$$* en...

  • Page 209: Enter Record

    Data entry commands - enter record 8-15 8 enter record purpose: transmits the record and clears it from memory. If no data exists, the reader transmits the eom character and any defined preambles or postambles. Use this command to exit from preamble/postamble entry modes. Terminal / keyboard enter h...

  • Page 210: Exit Auto-Trigger Mode

    Data entry commands - exit auto-trigger mode 8-16 exit auto-trigger mode purpose: sets the scanner to read one label per trigger pull. Enter this command a second time to return the laser to auto-trigger mode. Terminal / keyboard ctrl j host: $/ scan: exit auto-trigger mode *$/* *$/* exit computer r...

  • Page 211

    Data entry commands - exit configuration mode, do not save settings 8-17 8 exit configuration mode, do not save settings purpose: exits configuration mode without updating the parameters. Terminal / keyboard ctrl z host: -. Scan: exit configuration mode no save *-.* * - .* exit configuration mode, s...

  • Page 212: Exit Full Ascii Mode

    Data entry commands - exit full ascii mode 8-18 exit full ascii mode purpose: exits full ascii mode and decodes full ascii characters as code 39 data. Terminal / keyboard ctrl q host: - $ scan: exit full ascii *-$* * - $* exit irl editor purpose: exits the regular crt-based irl editor. Terminal / ke...

  • Page 213: Exit Program

    Data entry commands - exit program 8-19 8 exit program purpose: interrupts an irl program. The program is not resumed. Terminal: not applicable keyboard: ctrl-enter [e] note: simultaneously press ctrl and enter , and then press e . Host: /$ scan: exit program */$* */$* forward purpose: scrolls the d...

  • Page 214: High Beep

    Data entry commands - high beep 8-20 high beep purpose: generates a high beep when the computer sends a backslash character (\). Multiple \’s cause multiple high 60 msec beeps with a 45 msec delay between beeps. High and low beeps can be intermixed. Terminal / keyboard not applicable host: \ scan: n...

  • Page 215: Laser Untrigger

    Data entry commands - laser untrigger 8-21 8 laser untrigger purpose: turns the laser off. Terminal / keyboard not applicable host: /% scan: not applicable.

  • Page 216: Led/relay Control

    Data entry commands - led/relay control 8-22 led/relay control purpose: controls the four status leds of an attached 9191 digital wand station and the three internal relays of the 9560. Also returns the status of the sense inputs to the #0 register. You can enter up to eight valid data characters. T...

  • Page 217

    Data entry commands - led/relay control 8-23 8 scan: all relays on, leds to default *$%xxxx111x* *$%xxxx111x* all relays off, leds to default *$%xxxx000x* *$%xxxx000x*.

  • Page 218: Low Beep

    Data entry commands - low beep 8-24 low beep purpose: generates a low beep when the computer sends a bel. Multiple bels cause multiple 60 msec low beeps with a 45 msec delay between beeps. High and low beeps can be intermixed. Terminal / keyboard not applicable host: ctrl g or bel scan: not applicab...

  • Page 219: Preamble A

    Data entry commands - preamble a 8-25 8 preamble a purpose: enters up to 25 characters into the preamble a buffer to be transmitted with the data. For an explanation of preambles, see chapter 5, “data communications and operating options.” if you enter the preamble a command without entering data, t...

  • Page 220: Preamble B

    Data entry commands - preamble b 8-26 preamble b purpose: enters up to 25 characters into the preamble b buffer to be transmitted with the data. For an explanation of preambles, see chapter 5, “data communications and operating options.” if you enter the preamble b command without entering data, the...

  • Page 221: Postamble C

    Data entry commands - postamble c 8-27 8 postamble c purpose: enters up to 25 characters into the postamble c buffer to be transmitted with the data. For an explanation of postambles, see chapter 5, “data communications and operating options.” if you enter the postamble c command without entering da...

  • Page 222: Reset

    Data entry commands - reset 8-28 reset purpose: exits configuration mode without updating the parameters. Clears the data buffer. Terminal / keyboard ctrl z host: - . Scan: reset *-.* *-.* resume program purpose: resumes running an irl program from the point where the previously run program stopped....

  • Page 223: Review

    Data entry commands - review 8-29 8 review purpose: scrolls the display up one row in the current virtual display image if any rows of data have scrolled off the display. Terminal: not applicable keyboard: â â host: not applicable scan: review *%/* *%/* right host message purpose: transmits messages...

  • Page 224: Run Program

    Data entry commands - run program 8-30 run program purpose: executes an irl program beginning at the first statement. Terminal: not applicable keyboard: ctrl enter b note: simultaneously press ctrl and enter, and then press b. Host: // scan: run program *//* *//* transmit (no clear) purpose: transmi...

  • Page 225: Transmit File

    Data entry commands - transmit file 8-31 8 transmit file purpose: transmits an irl file to the host with the selected protocol. If you omit the filename, the reader prompts you to enter it. Terminal / keyboard not applicable host: %% filename the filename must be one character from a to z. Scan: 1. ...

  • Page 227: 9560

    Nugget code39 helconital 9560 7 8 9 4 5 6 1 2 3 - 0 . Bksp space enter d e caps i j $ n o / t , x y z a b c f g h k l m q u v w f1 f6 f2 f7 f3 f8 f4 f9 f5 f10 intermec p r s interactive reader language 9.

  • Page 228

    Nugget code39 helconital.

  • Page 229: Introduction to Irl

    Interactive reader language 9-3 9 this chapter explains how to use the irl editor and how to enter, change, and store irl programs. Sample programs are included: two for using the sense inputs/output relays and one for controlling the optional magnetic card reader. There is also a description of com...

  • Page 230: Irl Editor

    9560 transaction manager user’s manual 9-4 irl editor you use the irl editor to develop, input, and edit irl programs on the reader or on a terminal attached to the reader. The irl editor has two modes: command line mode and program edit mode. In command line mode the editor accepts any of the comma...

  • Page 231: Exiting The Irl Editor

    Interactive reader language 9-5 9 the reader enters command line mode and displays the following prompt: irl v2.1 >_ you can display the irl editor on the terminal screen by scanning the enter irl editor command label a second time. Exiting the irl editor the method you use to exit the irl editor de...

  • Page 232

    9560 transaction manager user’s manual 9-6 exiting from program edit mode input the command to exit without compiling to exit and compile from the host or scanner 1. Press enter at the beginning of a new line. The editor prompt is displayed. 2. Send the /$ command or scan the exit irl editor command...

  • Page 233: Compiling A Program

    Interactive reader language 9-7 9 to exit the insert mode and return to the irl editor • press enter at the beginning of a new program line. Compiling a program the e command exits the irl editor, compiles the program, and stores the program in the reader’s memory. To compile an irl program while in...

  • Page 234

    9560 transaction manager user’s manual 9-8 to resume an irl program • enter the $. Command or scan the resume irl program command label. If the program is resumed after prompts have been displayed, the prompts are lost. Resume irl program *$.* *$.* irl bar codes enter irl editor exit irl editor/prog...

  • Page 235: Function Output Command

    Interactive reader language 9-9 9 unique irl commands for the 9560 the 9560 uses standard irl 2.1 commands plus the function output command for the sense inputs and relays. Irl v2.1 and irl v2.2 differences irl 2.1 does not support the following irl 2.2 and later commands and operations: ymp. File r...

  • Page 236: Sample Program 1

    9560 transaction manager user’s manual 9-10 the digits correspond to the inputs as shown below: 0 1 1 register #0 first input j1 second input j2 third input j3 9560-40u for example, if the #0 register contains 011, it would indicate a signal at the first and second inputs, but none at the third inpu...

  • Page 237: Sample Program 2

    Interactive reader language 9-11 9 w2 :leave door open for 2 seconds. Fxxxx0000 :lock door. G.Start :return to beginning. :********************************************************************** :this subroutine compares the scanned badge with the valid badge * :numbers. * :**************************...

  • Page 238

    9560 transaction manager user’s manual 9-12 g#0=0.Goodsnd :if the transmission is good, wait for response. :********************************************************************** :the subroutine executes the following statements if the host does * :not respond. * :***********************************...

  • Page 239

    Interactive reader language 9-13 9 g#0=0.Start :nothing at the sense inputs, return to beginning. C$0=#0 :convert the input to string for test. D#1=[$0] :determine the string length. G#1=2.Alarm :if second bit is set, an alarm is detected. G#1=1.Doropen :if first bit is set, the door is open. G.Faul...

  • Page 240: Sample Program 3

    9560 transaction manager user’s manual 9-14 sample program 3 this program enables the 9560 to read data from the magnetic card reader. You must use this program or a similar program to control the internal magnetic card reader. If you ordered the 9560 with the internal magnetic card reader, you alre...

  • Page 241

    Interactive reader language 9-15 9 program listing #3 controlling the magnetic card reader :program - magdrvr.Irl intermec disk no. 061795 : copyright intermec, 1994 all rights reserved. : :*********************************************************************** :purpose - this program enables commun...

  • Page 242

    9560 transaction manager user’s manual 9-16 vtp;300 d$0="" q : :********************************************************************** :9560 receives data from mag stripe reader :********************************************************************** : .Magread b1 d#0=2 : default to terminal error q$...

  • Page 243: Reading Standard Data

    Interactive reader language 9-17 9 magnetic card reader commands the magnetic card reader accepts many data formats. Use the commands in this section to specify your data format and to create custom irl programs. Reading standard data the host may request the data from the reader in two ways: single...

  • Page 244

    9560 transaction manager user’s manual 9-18 read and transmit data commands command hex value operation p 0x50 clear storage and accept new data r 0x52 transmit standard data t2 from track 2 i 0x49 transmit error data (uppercase i ) r1 0x72 0x31 transmit track 2 data using ansi track format t1 r2 0x...

  • Page 245

    Interactive reader language 9-19 9 card reader responses to host command hex value operation ^ 0x5e command completed (ack) + 0x2b no data found * 0x2a error ? 0x3f retransmit (communication error) ! 0x21 invalid command ~ 0x7e cannot execute : 0x3a power on report.

  • Page 247: 9560

    Nugget code39 helconital 9560 7 8 9 4 5 6 1 2 3 - 0 . Bksp space enter d e caps i j $ n o / t , x y z a b c f g h k l m q u v w f1 f6 f2 f7 f3 f8 f4 f9 f5 f10 intermec p r s troubleshooting 10

  • Page 248

    Nugget code39 helconital.

  • Page 249: Troubleshooting Checklist

    Troubleshooting 10-3 10 this chapter provides simple troubleshooting procedures for some of the more common problems that the 9560 may experience. Troubleshooting checklist use the following tables to diagnose and correct minor problems with the 9560. Reader does not read bar code... Possible causes...

  • Page 250: Reader “Hung Up”...

    9560 transaction manager user’s manual 10-4 reader “hung up”... Possible causes try this irl program looping. Remove power from unit. Press and hold the exit irl switch (located on connector board) while restoring power. Exit irl switch j17 9560-47u exit irl switch slot scanner does not function... ...

  • Page 251: Status Beeps

    Troubleshooting 10-5 10 status beeps the reader beeps to indicate its status and condition. Error status beeps beeps error condition 4 low power was applied or unit was reset. Ram and rom are in proper working condition. High low high an input or output error occurred. 1 low a valid label was read, ...

  • Page 252: Communications Errors

    9560 transaction manager user’s manual 10-6 communications errors a communications error occurs when the reader fails to complete a transaction with the host. When an error occurs, the reader sounds three beeps (high low high) and displays the error message on the reader display or the crt terminal....

  • Page 253: Maximum Transmitted Data

    Troubleshooting 10-7 10 maximum transmitted data the maximum number of characters transmitted is 215 characters. That is 128 characters for the data, 75 characters for the preambles and postamble, and 12 characters for time. Any protocol characters used during data transmission are not calculated in...

  • Page 255: 9560

    Nugget code39 helconital 9560 7 8 9 4 5 6 1 2 3 - 0 . Bksp space enter d e caps i j $ n o / t , x y z a b c f g h k l m q u v w f1 f6 f2 f7 f3 f8 f4 f9 f5 f10 intermec p r s specifications a.

  • Page 256

    Nugget code39 helconital.

  • Page 257

    Specifications a-3 a this appendix lists the hardware and software specifications for the 9560. It includes bar code symbologies, physical and environmental specifications, interfaces, protocols supported, and configuration methods bar code symbologies supported code options code 39 hibc i 2 of 5 fi...

  • Page 258: Operator Feedback

    9560 transaction manager user’s manual a-4 operating environment operating temperature range 32 ° f to 122 ° f 0 ° c to +50 ° c storing temperature range -4 ° f to 158 ° f -20 ° c to +70 ° c operating humidity 10% to 90% relative humidity operator feedback a cone speaker on the base of the 9560 beep...

  • Page 259: Hardware Interfaces

    Specifications a-5 a hardware interfaces port interface connectors modem rs-232-c 25-pin, d-subminiature, wired as dte rs-422 terminal rs-232-c connector: 25-pin, d-subminiature, wired as dce rs-422 pin assignments for 6-pin wand connector pin signal direction 1 +12v 2 +5v 3 ground 4 ground 5 video ...

  • Page 260

    9560 transaction manager user’s manual a-6 pin assignments for 25-pin modem connector pin signal direction 1 chassis ground (optional) 2 transmitted data outgoing 3 received data incoming 4 request to send outgoing 5 clear to send incoming 7 signal ground (required) 11 remote triggering (when enable...

  • Page 261: Configuration Methods

    Specifications a-7 a input devices compatible with the 9560 model and description connect to 1260 and 1270 series digital wands wand (modular) connector 1350 series badge scanners wand (modular) connector 1500 and 1600 series laser scanners (with 9-pin d-sub connector) laser scanner connector 1700 k...

  • Page 263: 9560

    9560 7 8 9 4 5 6 1 2 3 - 0 . Bksp space enter d e caps i j $ n o / t , x y z a b c f g h k l m q u v w f1 f6 f2 f7 f3 f8 f4 f9 f5 f10 intermec p r s full ascii chart b.

  • Page 265: Ascii Bar Code Labels

    Full ascii chart b-3 b this appendix lists each character in the full ascii chart with a multiple-read code 39 bar code label. Ascii bar code labels to use these labels, you must set the 9560 in full ascii mode. For a description of multiple-read labels, see chapter 5, “data communications and opera...

  • Page 266: Control Characters

    9560 transaction manager user’s manual b-4 control characters ack * $f* * $f* del * %t* * %t* fs * %b* * %b* sub * $z* * $z* bel * $g* * $g* dle * $p* * $p* gs * %c* * %c* syn * $v* * $v* bs * $h* * $h* em * $y* * $y* ht * $i* * $i* soh * $a* * $a* can * $x* * $x* enq * $e* * $e* lf * $j* * $j* stx ...

  • Page 268: Numbers

    9560 transaction manager user’s manual b-6 numbers 0 * 0* * 0* 4 * 4* * 4* 8 * 8* * 8* 1 * 1* * 1* 5 * 5* * 5* 9 * 9* * 9* 2 * 2* * 2* 6 * 6* * 6* 3 * 3* * 3* 7 * 7* * 7*.

  • Page 269: Uppercase Letters

    Full ascii chart b-7 b uppercase letters a * a* * a* h * h* * h* o * o* * o* v * v* * v* b * b* * b* i * i* * i* p * p* * p* w * w* * w* c * c* * c* j * j* * j* q * q* * q* x * x* * x* d * d* * d* k * k* * k* r * r* * r* y * y* * y* e * e* * e* l * l* * l* s * s* * s* z * z* * z* f * f* * f* m * m* ...

  • Page 270: Lowercase Letters

    9560 transaction manager user’s manual b-8 lowercase letters a * +a* * +a* h * +h* * +h* o * +o* * +o* v * +v* * +v* b * +b* * +b* i * +i* * +i* p * +p* * +p* w * +w* * +w* c * +c* * +c* j * +j* * +j* q * +q* * +q* x * +x* * +x* d * +d* * +d* k * +k* * +k* r * +r* * +r* y * +y* * +y* e * +e* * +e* l...

  • Page 271: 9560

    9560 7 8 9 4 5 6 1 2 3 - 0 . Bksp space enter d e caps i j $ n o / t , x y z a b c f g h k l m q u v w f1 f6 f2 f7 f3 f8 f4 f9 f5 f10 intermec p r s command summary c.

  • Page 273: Command Summary

    Command summary c-3 c this appendix lists the commands that the 9560 recognizes in data entry mode or in an irl program. For a complete description of the data entry commands, see chapter 8, “data entry commands.” for a complete description of irl commands, refer to the irl programming reference man...

  • Page 274

    9560 transaction manager user’s manual c-4 data entry mode command summary data entry mode entered from this source command name label host terminal keyboard enter preamble a +. Data +. Data ctrl-a data ctrl-a data clear preamble a +. +. Ctrl-a ctrl-a enter preamble b ++ data ++ data ctrl-b data ctr...

  • Page 275

    Command summary c-5 c data entry mode entered from this source command name label host terminal keyboard laser trigger not used /. Not used not used laser untrigger not used /% not used not used set clock /+ data /+ data not used not used right host msg not used not used not used review %/ not used ...

  • Page 276: Irl Run Mode Command Summary

    9560 transaction manager user’s manual c-6 irl run mode command summary irl entered from this source command name label host terminal keyboard irl z command enter preamble a not used not used not used not used +. Data clear preamble a not used not used not used not used +. Enter preamble b not used ...

  • Page 277

    Command summary c-7 c irl entered from this source command name label host terminal keyboard irl z command default configuration not used not used not used not used not used laser trigger not used /. Not used not used /. Laser untrigger not used /% not used not used /% set clock not used /+ ctrl-t c...

  • Page 279: 9560

    9560 7 8 9 4 5 6 1 2 3 - 0 . Bksp space enter d e caps i j $ n o / t , x y z a b c f g h k l m q u v w f1 f6 f2 f7 f3 f8 f4 f9 f5 f10 intermec p r s glossary g.

  • Page 281: Glossary

    Glossary g-3 g this glossary defines general data collection terms and terms used in this manual. Glossary 2 of 5 code a discrete, self-checking code for encoding numeric data only. The bars encode information, and the spaces separate individual bars. It can achieve densities of 15 characters per in...

  • Page 282

    9560 transaction manager user’s manual g-4 autodiscrimination capability of a reader to read multiple symbologies automatically without a significant change in first read rate or substitution error rate. Bak bad program acknowledgment character sent from the reader when the received irl program has ...

  • Page 283

    Glossary g-5 g bidirectional a bar code symbol that can be read successfully independent of scanning direction. Bit an abbreviation for binary digit. A single element (0 or 1) in a binary number. Byte a combination of eight bits in a predetermined pattern, designed to represent a digit or alphanumer...

  • Page 284

    9560 transaction manager user’s manual g-6 code 39 alphanumeric bar code that is discrete, variable length, and self-checking. Character set includes a start/stop character, 10 digits, 26 letters of the alphabet, space, and six symbols. Ascii characters are represented by the alphanumeric characters...

  • Page 285

    Glossary g-7 g continuous code continuous bar code symbol a bar code or symbol in which the space between two characters (intercharacter gap) is part of the code, such as usd-1 (interleaved 2 of 5 code). A continuous code is the opposite of a discrete code. Contrast amount of difference in reflectan...

  • Page 286

    9560 transaction manager user’s manual g-8 echoplex communication environment in which full duplex terminals work. Any data sent to the host is echoed back to the device that sent the data. Edge trigger mode the laser only turns on or off when you pull the trigger–it completely ignores the trigger r...

  • Page 287

    Glossary g-9 g eop end of program block/continue character sent by the host after transmitting a block of irl program statements to the reader. Indicates the end of an intermediate block of program data and that more program data will be transmitted. Eor end of record character 1. Attached to the en...

  • Page 288

    9560 transaction manager user’s manual g-10 hibc health industry bar code standard. A modified version of code 39 that has 43 characters, utilizes the modulus 43 check character, and reserves some character combinations for special usage. Human readable contents of a bar code symbol that can be read...

  • Page 289

    Glossary g-11 g laser light amplification by the stimulated emission of radiation. A coherent, monochromatic light source produced by directing a light beam repeatedly through an active material so that it becomes amplified, and then directing the beam into a narrow cone of divergence. The active ma...

  • Page 290

    9560 transaction manager user’s manual g-12 misread bad read a condition that occurs when the data output of a reader does not agree with the encoded data presented. Modem modular/demodular; a device that converts one form of a signal to another that is suitable for transmission over communication c...

  • Page 291

    Glossary g-13 g parity a system for encoding characters with odd or even bar code patterns. Parity provides a self-checking feature in bar codes and other data transmission techniques. Even parity characters have an odd number of binary ones in their structure. Parity, for the purposes of data proce...

  • Page 292

    9560 transaction manager user’s manual g-14 polling mode d protocol communications protocol for connecting the reader to a 9160a or 9161a port concentrator or a 9165b system control unit. Polling mode d operates only at 2400 baud or higher and cannot be modified. Preamble predefined data that is aut...

  • Page 293

    Glossary g-15 g res reset character sent by the reader to end communication with the host. Enables or disables the reset event and/or resets the data transmission event to the solicitation event. Reset event terminates the current data transmission event and resets the communication event to the sol...

  • Page 294

    9560 transaction manager user’s manual g-16 scanner a device that examines a spatial pattern, one part after another, and generates analog or digital signals corresponding to the pattern. Scanners are often used in mark sensing, pattern recognition, character recognition, and bar code recognition. T...

  • Page 295

    Glossary g-17 g space the light element of a printed bar code symbol. The white lines. Start/stop characters distinct characters used at the beginning and end of each bar code symbol that provide initial timing references and direction of read information to the coding logic. For hibc purposes, the ...

  • Page 296

    9560 transaction manager user’s manual g-18 upc universal product code a 12-digit bar code pattern adopted by the u.S. Grocery industry. Encodes the number system character (type of encoded product), five-digit manufacturer number assigned by the upcc, five-digit product code assigned by the manufac...

  • Page 297: 9560

    9560 7 8 9 4 5 6 1 2 3 - 0 . Bksp space enter d e caps i j $ n o / t , x y z a b c f g h k l m q u v w f1 f6 f2 f7 f3 f8 f4 f9 f5 f10 intermec p r s index i.

  • Page 299: Index

    Index i-3 i index numbers 1700 keyboard, 1-6, 6-4, 8-4 1x20 character display, 1-5, 5-12, 6-21 2 of 5, 1-7, 6-4, g-3 2 of 5 command, 7-56 2x40 character display, 1-5, 5-12, 6-16 9191 satellite wand station, 1-6, 2-5 9560 transaction manager, description, 1-4 a abc symbol, g-3 accumulate mode, 5-31, ...

  • Page 300

    9560 transaction manager user’s manual i-4 c cable interface, 2-10 cable requirements, 2-10 cable/connectors for multi-drop wiring, 2-17 capacity command, 8-5 card reader reading magnetic cards, 4-7 proper scanning, 4-6 character set, 5-19, g-5 character set command, 7-9 chart, us-ascii, 5-20 circul...

  • Page 301

    Index i-5 i command, data entry continued enter prompting configuration mode, 8-14 enter record, 8-15 exit accumulate mode, 8-15 exit auto-trigger mode, 8-16 exit configuration mode, 8-17 exit crrm, 8-16 exit full ascii mode, 8-18 exit irl editor, 8-18 exit program, 8-19 forward, 8-19 high beep, 8-2...

  • Page 302

    9560 transaction manager user’s manual i-6 defined terms, xviii defining a secure protocol, 5-8 delay intercharacter, 5-9 timeout, 5-9, 6-6, 6-7, 6-8, 7-54 turnaround, 5-9, 6-6, 6-7, 6-8, 7-55, g-17 delete data command, 8-9 dimensions, a-3 display clearing, 5-15 commands, 5-15 control codes, 5-13 fo...

  • Page 303

    Index i-7 i g getting started, 1-3 glossary, g-3 h half-duplex, 5-4 device, 5-5 nonbuffered terminal, 5-15, 5-18 protocol, 5-5, 5-7 handaku on characters, 5-30 hardware interface, a-5 headphones, 2-9, 3-12 help command, 6-13, 6-14 hibc, 1-7, 6-16, g-10 high beep command, 8-20 home command, 5-13 host...

  • Page 304

    9560 transaction manager user’s manual i-8 k kana mode characters, 5-25 to 5-29 katakana, 5-23 to 5-30 assigning function keys, 5-26 lowercase characters, 5-28 to 5-30 character set, 5-19, 5-23, to 5-30, 7-33, 9-14 entering characters, 5-25 katakana command, 7-33 keyboard for 9560, 1-5 keyboard, usi...

  • Page 305

    Index i-9 i output relays, continued description, 2-9 sample application, 2-9 typical application, 3-12 oversize display, 5-12 p pak, 6-9, 7-29, g-12 pak command, 7-29 parity command, 7-38 pc-irl, 9-9 pin assignments 25 pin modem connector, 2-11 25 pin terminal connector, 2-12 25-pin modem connector...

  • Page 306

    9560 transaction manager user’s manual i-10 review command, 5-15, 8-29 right host message command, 8-29 roadmap, 1-3 ro-maji characters, 5-25, 5-29, 5-30 ro-maji spelling, 5-29, 5-30 routing cables, 3-5, 3-14 routing wires, 3-14 rs-232, 1-7, 2-10 rs-422, 1-7, 2-10 rs-485 multi-drop, 1-7, 2-10, 2-16 ...

  • Page 307

    Index i-11 i transmit file command, 8-31 transmit(noclear) command, 8-30 transparent display settings, 5-13 transparent terminal, 5-15 full-duplex, 5-17 transparent terminal operation, 5-17 trigger event command, 7-52 trigger mode, 2-7, 7-47 triggering auto, 7-47 edge, 7-52 level, 7-52 one-shot, 7-4...

  • Page 309

    Nugget c o d e 3 9 helconital addendum to the 9560 user’s manual the terminal port of the 9560e transaction manager is not available for use. Terminal port functions described in the 9560 transaction manager user’s manual are not supported. Terminal port not supported . Connector pcb a western atlas...