1. DL manuals
  2. J-Power
  3. Toy
  4. B-60
  5. Assembly And Operating Manual

J-Power B-60 Assembly And Operating Manual

Summary of B-60

  • Page 1

    Assembly and operating manual b‐60 specification: *length: 58‐7/10"(1490 mm) *wing span: 63"(1600 mm) *flying weight: 88‐1/5 oz (2500g).

  • Page 2

    Assembly and operating manual b-60 2 dear customer, congratulations on your choice of a factory-assembled model aircraft from the jpower light plane range and thank you for placing your trust in us. The model can very quickly be completed ready to fly. Please read right through these instructions an...

  • Page 3

    Assembly and operating manual b-60 3 figs. 1 - assemble the control horns with their backing plates to the elevators figs. 2 - photo shows the control horns assembled in the elevators. Fig. 3 -assemble the control horns with their backing plates to the vertical fin . Fig. 4 - photo shows the control...

  • Page 4

    Assembly and operating manual b-60 4 fig. 5 -6 -glue each of the three flap hinges into their prepared locations in the wings and the flaps. Check their exact positioning allow to dry thoroughly. Fig. 7 -assemble the control horns with their backing plates to the aileron. Fig. 8 - assemble the contr...

  • Page 5

    Assembly and operating manual b-60 5 fig. 9 -connect the horizontal tail push rod to the servo arm at second hole. Photo shows the finished view. Fig. 10 -connect the vertical tail push rod to the servo arm at second hole. Photo shows the finished view. Figs. 11 -connect the wing flap push rod to th...

  • Page 6

    Assembly and operating manual b-60 6 figs. 13 -feed the servo lead through the rear of the fuselage. Slide the m 3 x 55 bolt in position. Figs. 14 -place tailplane in position and screw in position, feed the lead toward the nose.. Figs. 15 -turn over and screw the vertical fin from the underneath. F...

  • Page 7

    Assembly and operating manual b-60 7 time feeding the lead towards the nose. Figs. 17 - place servo leads in the fuselage and pull towards the nose. Trial fit the fuselage rear and check for exact fit. Figs. 18 - epoxy the tailplane unit to the fuselage.Pay attention that the fin and fin fairing are...

  • Page 8

    Assembly and operating manual b-60 8 figs. 21 - trim the dummy exhausts from their backing piece with a sharp knife and glue into their position in the engine nacelle undersides. Figs. 22 -set the motor air intakes on the nacelles and screw in place. Figs. 23 -glue the left and right wingtips to the...

  • Page 9

    Assembly and operating manual b-60 9 figs. 25-26 -dry assemble the wings with the connector to check correct fit. - coat the complete connector and root area of one wing panel with white glue and fit the wings in place. Pay attention that the wing half alignment is perfect with each other and that t...

  • Page 10

    Assembly and operating manual b-60 10 figs. 29-30 - - fit the prop driver to the motor shaft. Leave a distance of 3 - 4 mm between spinner backplate and cowling. Tighten the prop nut securely using an 8 mm spanner. Figs. 31-32 -fit the spinner cap and the retaining screws. -repeat the procedure for ...

  • Page 11

    Assembly and operating manual b-60 11 figs. 33 -photo shows the throttle channel connect to receiver. Figs. 34 - place the flight battery in the fuselage. Figs. 35 - photo shows battery leads connected to the speed controller. Figs. 36 -glue aerial into fin. 35 34 36 33.

  • Page 12

    Assembly and operating manual b-60 12 figs. 37 -glue aerial into cabin roof, figs. 38 -place the cabin top in position and click into position at the rear. Figs. 39 -photo shows the finished view. 38 39 37.

  • Page 13

    Assembly and operating manual b-60 13 figs. 40 -congratulation! You have done all the assemble step. Figs. 41 photo shows the balancing weight. 40 41.

  • Page 14

    Assembly and operating manual b-60 14 fig.42 - charge the flight battery; connect the equalizer lead using and adapter lead matching your charger (adapter lead not included). Fig.43 - switch the transmitter on, and move the throttle stick to the “motor off” position. (diagram mode 1 right throttle c...

  • Page 15

    Assembly and operating manual b-60 15 fig.44-47 function test check the channel assignment at the receiver, and if necessary swap the plugs as necessary. - set the transmitter sticks and trims to centre. - the control surfaces should now also be at centre (neutral). Adjust the clevis where necessary...

  • Page 16

    Assembly and operating manual b-60 16 preference. Fig. 48 checking the electric power system - caution: position the throttle stick in such a way that the motor cannot possibly start running. 48.

  • Page 17

    Assembly and operating manual b-60 17 - switch the transmitter on, and connect the flight pack check the direction of rotation of the motor: when viewed from the front, the output shaft must rotate anti-clockwise. If this is not the case, perhaps because you are using components other than those rec...

  • Page 18

    Assembly and operating manual b-60 18.

  • Page 19

    J-power group co.,ltd 5th floor, a3 building, xinjianxing technology industrial park, fengxin road, guangming town, bao'an, shenzhen city, 518107 china phone: +86 755 33699201 fax: +86 755 33699203 www.Jpower.Hk.