- DL manuals
- Jack
- Sewing Machine
- JK-SHIRLEYIIE
- Operation And Daily Service Manual
Jack JK-SHIRLEYIIE Operation And Daily Service Manual
Summary of JK-SHIRLEYIIE
Page 1
Operation and daily service manual jk-shirleyiie www.Chinajack.Com edited by customer service center translated by international trade department.
Page 2: Contents
Product and technical parameter instruction of operation panel preparation before trial sewing instruction of mechanical adjustments instruction of pedal control application of needle position selection of mode speed trial sewing needle position presser foot lifter thread tension device bar tacking ...
Page 3
Jk-shirleyiie with powermax control box presser foot pk simple beautiful efficient saving energy stable low noise 1.
Page 4
Technical parameter jk-shirleyiie model fabric needle size maximum needle gauge auto-bar tacking auto-press foot lifter auto-trimmer max height of press foot lifter factory setting of press foot lifter distance of press foot by hand lifter max speed thread tension integrated computerized lockstitch ...
Page 5
Mechanical adjustments the first tension device adjustment control the length on the needle after automatic trimming and the thread length around 4-4.5 cm is the best. Adjusting the knob in clockwise way, thread will be short; otherwise, it will be long. The main tension device adjustment control th...
Page 6
Press this key, the machine enters into “free sewing mode”, the sewing length can be controlled by the operator, that is why we called this function as“free sewing model”. It’s often used for lap seam and bar- tacking sewing. Press this key, the machine enters into “fixed-stitch sewing mode”, the se...
Page 7
Speed keeping press then press , will be displayed “pd-0000”, press enter “p62-2101”, press to confirm. Parameter code p00 p01 p02 p03 p05 p10 p11 p12 default 200 3500 3000 3000 250 1800 1800 1800 parameter definition beginning sewing speed sewing speed fixed-length sewing speed manual reinfored sew...
Page 8
Presser foot lifter thread tension device press and it can open or close small thread tension device easily 1.After the user press the ,and it press the at the same time,it will enter into system parameter modification mode 2.P19:choose clamp thread function:(0:off,1:on) p1a:angle for clamping threa...
Page 9
Adjustment of feed dog height adjustment for feed dog unscrew the braces screw for light fabric, appropriately adjust feed dog lower for heavy fabric, appropriately adjust feed dog higher .After finishing ,tighten the screws. Adjustment for feed dog gradient unscrew the screw,turn the brace and adju...
Page 10
Thread trimming standard method of adjustment trimming needle bar running direction hook running direction hook scattering thread point needle center line the distance between hook scattering thread point and need center line is about 5mm retaining screw of trimming cam trimming driving ball movable...
Page 11
Press button first, then press . When the displayer shows pd-0000, press button to enter p62-2101, again press button to save. Factory reset (err-01) reason: hardware overcurrent the way to check: 1. 2. Replace the control box with “replace exclusion method” to see whether the control box is damage ...
Page 12
( -10) err reason: panel no display or panel no power the way to check: 1.Check if connection between panel and control box is broken or not. 2.Interchange the panel to check if it is the panel problem. 3.Interchange the control box to check if it is the control box problem. Solution: 1.If connectio...
Page 13
Daily maintenance keep the machine surface clean keep the oil in the oil reservoir not lower than the scale make sure that there's oil spraying up in the oil sight window during running keep the small oil reservoir clean, no thread dust gathering keep the big oil reservoir with clean oil, not gettin...
Page 14
The fabric not flat enough bottom thread is break needle break whether the presser foot pressure is too weak to adjust the pressure of presser foot high-low about the feed dog , whether not flatness to adjust the feed dog height and parallelism whether the bottom thread is suitable to adjust the bot...
Page 15
The common problems and solutions of jk-shirley iie （powermax） 1 q: how to lift presser foot when we are sewing? Answer: the control system of this type of sewing machine has the function that operators just need to press the button “presser foot lift”continuously to achieve circulatory switch betwe...
Page 16
Unnecessary to raise presser foot. When machine is bone only operator only need to pull with hand before sewing, and it is absolutely unnecessary to raise presser foot. On the contrary, stitch length is uneven and stitch trace is caused not beautiful if the presser foot is raised. On this point we h...
Page 17
Into the “ parameter mode of system operator”p42. You can modify the upper stop position through adjusting the parameter value of p42,and modify the under stop position through adjusting the value “p43”.After finishing adjustment, press “p” to store it. 22 q:how to adjust the speed? Answer: press th...
Page 18
Memo memo.