Jacob Jensen IP60 User Manual - page 3
4
5
Congratulations on your new JACOB JENSEN
TM
Telephone
IP60.
The telephone is designed in Denmark by Jacob Jensen,
whose products have gained international recognition for
their original, simple and classic design. Jacob Jensen has
received about 100 prizes from around the world and has
19 products included in The Design Study Collection and
The Design Collection of The Museum of Modern Art in
New York.
The IP60 has been designed specifically for hotel use. Voice
over IP technology is employed for clear sound and reliable
operation. SIP protocols ensure compatibility with all major
brands.
A.
INSTALLATION
A.1. Base installation – table stand
Disassembly:
A.2. Faceplate installation
123
123
123
123
123
123
123
123
123
123
123
123
123
123
123
123
A.3. Install the handset cord
1. Insert one end of the attached handset cord to the jack on
the handset, the other end to the jack of the base
2. Correctly install the battery
3. Connect the WAN port with the POE port of the PBX via
internet cable
4. The default mode is DHCP.
For more information, refer to
telephone configuration setup description.
Note:
1. Please install the phone in dry and clean environment and
avoid effected with damp.
2. The telephone should avoid fire, water spray, shock,
clean the surface dust by soft cloth; chemical solvent is
prohibited to use.
B.
CONFIGURATION WITH WEB BROWSER
When the telephone and the PC are connected to the
network, open the browser Internet Explorer and enter the
IP address. (In on-hook mode, press
MUTE
to get the local IP
address).
Type in username and password, then press ENTER to log
on to the interface. On first use, leave password blank and
press enter. The Administrator Password can be set under
Network, System Settings.
Note:
1. Each time a parameter is changed, please click (OK) to
save the setting.
2. The factory default network settings mode is DHCP. In
this mode the phone requests an IP address and network
parameters automatically. In the absence of a DHCP server,
PPPoE or Static IP modes are available.
3. PC preparation work before telephone setup.
After confirming the telephone IP, first make sure PC’s
network connection to telephone is okay, then set up the
PC to guarantee the PC can visit telephone normally. For
example, telephone IP is 192.168.1.171, then PC’s IP needs
to be set up as 192.168.1.***(*** can be any number
between 0 to 255 except for 171).
C.
WEB FUNCTIONAL DESCRIPTIONS
C.1 Network settings
Connection Type:
Choose the way of getting IP
address, default setting is DHCP.
IP Address:
If the SIP supplier offers static
IP address, input the static IP
address.
Subnet Mask:
Input subnet Mask
Default Gateway:
Input default gateway address.
Primary DNS:
Input primary DNS services
address.
Secondary DNS:
Input secondary DNS server.
Voice VLAN ID:
Enter the VLAN PBX’s voice ID.
Data VLAN ID:
Enter the VLAN PBX’s data ID.
C.2 SIP settings
SIP Proxy:
Configure the SIP server address.
SIP User ID:
Configure the SIP registration
account.
SIP Authentication ID:
Configure the SIP registration
certification.
SIP Authentication PIN:
Configure the SIP account
password.
User Name:
Configure the SIP account user
name.
Subscribe for MWI:
Configure phone voice mail
indicator, if voice mail function is
available, phone MSG indicator
would shine.
Message Service Number:
Configure voice mail number
extraction.
Use Hotline:
Configure whether hotline
function is enabled.
Hotline Number:
Configure the hotline number.
Note:
Please choose YES for SIP Registration.
C.3 Voice configuration
Preferred Voice Codec:
Configuration mode of voice
CODEC
Use # to dial
immediately:
Configure whether # speed dial
function enabled or not.
The time wait to dial out:
Configure the time for sending
the dialled number.
The pause time (1-5s):
Configure PAUSE time.
Note: Please click the OK button when all the settings are
finished, the phone will automatically store the settings and
reboot.
UK