Jacobsen 63280 PGM 22 Technical Manual - 5    Controls

Other manuals for 63280 PGM 22: Technical Manual

Summary of 63280 PGM 22

  • Page 1

    Pgm pgm 63280 – pgm 22, honda gx120 engine 63280 – pgm 22, honda gx120 motor 4131595-de technical manual technische handbuch gb de warning: if incorrectly used, this machine can cause severe injury. Those who use and maintain this machine should be trained in its proper use, warned of its dangers an...

  • Page 2: To Order Parts

    Copyright 2005 textron inc. “all rights reserved, including the right to reproduce this material or portions thereof in any form.” to order parts 1. Write your full name and complete address on the order. 2. Explain where and how to make shipment. 3. Give product number, name and serial number that ...

  • Page 3: Suggested Stocking Guide

    3 suggested stocking guide to keep your equipment fully operational and productive, maintain a stock of the more commonly used maintenance items. We have included part numbers for additional support materials and training aids. A more complete listing of accessories and attachments can be found in t...

  • Page 4: 1    Safety

    1 safety 4 1 safety 1.1 operating safety ______________________________________________________ 1. Safety is dependent upon the awareness, concern and prudence of those who operate or service the equipment. Never allow minors to operate any equipment. 2. It is your responsibility to read this manual...

  • Page 5: Safety    1

    Safety 1 5 1.2 important safety notes ________________________________________________ this safety alert symbol is used to alert you to potential hazards. Danger - indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. Warning - indicates a potenti...

  • Page 6: 2    Specifications

    2 specifications 6 2 specifications 2.1 product identification _________________________________________________ 63280 .........22 in., (559 mm) professional greens mower with incommand™ control system, 4.0 h.P. Gasoline engine (honda), operator presence control, grass catcher, brakes and kickstand....

  • Page 7: Specifications    2

    Specifications 2 7 2.5 weight__________________________________________________________________ weight (mass) pgm 22....... 187 lb., (85 kg) with catcher, roller, kickstand. 2.6 accessories ____________________________________________________________ contact your authorized jacobsen dealer for a com...

  • Page 8: 3    Decals

    3 decals 8 3 decals 3.1 decals _________________________________________________________________ familiarize yourself with the decals, they are critical to the safe operation of the mower. Replace damaged decals immediately. To prevent injury and accidental clutch engagement do not adjust engine spe...

  • Page 9: Initial Inspection    4

    Initial inspection 4 9 4 initial inspection 4.1 general ________________________________________________________________ the set-up and testing of the unit should always be performed by a trained technician, familiar with the operation of the equipment. Read each instruction completely and make sure...

  • Page 10: 5    Controls

    5 controls 10 5 controls 5.1 icons ___________________________________________________________________ 5.2 controls ______________________________________________________________ a. Parking brake – used whenever the mower is left unattended or as a service brake while transporting. B. Paddle throttl...

  • Page 11: Controls    5

    Controls 5 11 e. Reel clutch lever – to disengage, turn handle (e) to point downwards. Always disengage clutch when mower is being transported. F. Choke lever - the choke lever opens and closes the choke valve in the carburetor. The closed position enriches the fuel mixture for starting a cold engin...

  • Page 12: 6    Operation

    6 operation 12 6 operation 6.1 daily inspection________________________________________________________ 1. Perform a visual inspection of the entire unit, look for signs of wear, loose hardware, and missing or damaged components. Check for fuel or oil leaks. 2. Check the fuel supply and crankcase oi...

  • Page 13: Operation    6

    Operation 6 13 6.3 operating procedures _________________________________________________ 1. Under no circumstances should the engine be started with operator or bystanders standing in front of the reel. 2. Never run the engine in an enclosed area. 3. Keep hands and feet away from moving parts and c...

  • Page 14: 6    Operation

    6 operation 14 6.4 starting/stopping engine ______________________________________________ starting 1. Check oil level and fuel supply then open fuel valve lever (g). 2. Move the choke lever (f) to the “closed” position. 3. Set engine switch (d) to “on”. 4. Make certain the o.P.C. Bail (c) is diseng...

  • Page 15: Operation    6

    Operation 6 15 6.5 transport wheels (optional kit 62293) _________________________________ 1. Push and hold the kickstand against the ground then pull the mower handle back until the mower rests on the stand (l). 2. To remove wheels, press retaining clip (j) away from the hub and pull wheel off hub....

  • Page 16: 6    Operation

    6 operation 16 6.7 mowing _________________________________________________________________ 1. Stop engine. Place mower on kickstand and remove the transport wheels if installed. (see section 6.5) 2. Engage the reel lever (e) and push mower off the kickstand. Start the engine. 3. Position mower slig...

  • Page 17: Operation    6

    Operation 6 17 6.8 daily maintenance______________________________________________________ 1. Park the mower on a flat, level surface. Engage parking brake and stop the engine. 2. Grease and lubricate all points if required. 3. To prevent fires, wash the mower after each use. Clean all grass clippin...

  • Page 18: 7    Adjustments

    7 adjustments 18 7 adjustments 7.1 general________________________________________________________________ 1. Adjustments and maintenance should always be performed by a qualified technician. If proper adjustment cannot be made, contact an authorized jacobsen. 2. Replace, do not adjust, worn or dama...

  • Page 19: Adjustments    7

    Adjustments 7 19 7.3 bedknife _______________________________________________________________ 1. Read section 7.2 before making the adjustment. 2. Start adjustment at the leading end of the reel, followed by the trailing end. The leading end of the reel blade is the end that passes over the bedknife...

  • Page 20: 7    Adjustments

    7 adjustments 20 7.5 cutting height _________________________________________________________ note: make sure the bedknife is properly adjusted before setting the cutting height. (section 7.3). 1. Tip mower back on traction drum or tires. Do not leave the mower tipped back for an extended length of ...

  • Page 21: Adjustments    7

    Adjustments 7 21 7.7 torque specification ___________________________________________________ jacobsen uses grade 5 plated bolts as standard, unless otherwise noted. When tightening plated bolts, use the value given for lubricated. Caution all torque values included in these charts are approximate a...

  • Page 22: 8    Maintenance

    8 maintenance 22 8 maintenance 8.1 general________________________________________________________________ 1. Adjustment and maintenance should always be performed by a qualified technician. If proper adjustments cannot be made, contact an authorized jacobsen. 2. Inspect the equipment on a regular b...

  • Page 23: Maintenance    8

    Maintenance 8 23 8.3 engine oil ______________________________________________________________ check the engine oil at the start of each day, before starting the engine. If the oil level is low, remove oil filler cap and add oil as required. Perform initial oil change after the first 20 hours of ope...

  • Page 24: 8    Maintenance

    8 maintenance 24 8.5 bedknife shoe removal ________________________________________________ 1. To remove the shoe (e), loosen nut (a) and turn nuts (b) counterclockwise 1/4 turn or more to bring the bedknife into light contact with the reel blades. 2. Remove mounting hardware (d) from both sides of ...

  • Page 25: Maintenance    8

    Maintenance 8 25 8.8 wheel bearing _________________________________________________________ the bearing has the word “lock” and an arrow stamped on the face. When replacing the bearing, make absolutely certain that the bearing is installed in the proper direction of rotation. For the right wheel, i...

  • Page 26: 8    Maintenance

    8 maintenance 26 8.10 troubleshooting ______________________________________________________ before making any adjustments or performing maintenance, read maintenance section for procedures and warnings. Symptoms probable causes solution engines does not start choke in wrong position see engine manu...

  • Page 27: Maintenance    8

    Maintenance 8 27 8.11 lubrication ____________________________________________________________ the mower was designed for minimum lubrication. Over greasing will produce high loads on the bearings and engine; thereby reducing the performance of the machine. All maintenance intervals must be performe...

  • Page 28: 9    Notes

    9 notes 28 9 notes.

  • Page 29: Notes    9

    Notes 9 29.

  • Page 30: Bestellen Von Ersatzteilen

    Copyright 2005, textron inc. "alle rechte vorbehalten, einschließlich des rechts, dieses material oder teile davon auf irgendeine weise zu reproduzieren." bestellen von ersatzteilen 1. Schreiben sie ihren vor- und zunahmen sowie ihre vollständige adresse auf die bestellung. 2. Erklären sie, wann und...

  • Page 31: Empfohlener Lagerbestand

    3 empfohlener lagerbestand damit ihr gerät voll einsatzbereit und produktiv bleibt, sollten sie die häufig verwendete wartungsteile auf lager halten. Wir haben die teilnummern für zusätzliches unterstützungs- und schulungsmaterial hinzugefügt. Eine vollständigere liste von zubehör und zusatzteilen f...

  • Page 32: 1    Sicherheit

    1 sicherheit 4 1 sicherheit 1.1 betriebssicherheit ____________________________________________________ 1. Die sicherheit hängt von der aufmerksamkeit, der vorsicht und dem interesse der personen ab, die das gerät bedienen und/oder warten. Minderjährige dürfen keine geräte bedienen. 2. Es liegt in d...

  • Page 33: Sicherheit    1

    Sicherheit 1 5 1.2 wichtige hinweise zur sicherheit _______________________________________ dieses warnsymbol wird verwendet, um sie auf potentielle gefahren aufmerksam zu machen. Gefahr - weist auf eine sofortige gefahrensituation hin, die einen todesfall oder eine ernsthafte verletzung zur folge h...

  • Page 34: 2    Technische Daten

    2 technische daten 6 2 technische daten 2.1 produktkennzeichnung ________________________________________________ 63280 .............................. 559 mm professional greens rasenmäher mit incommand™- steuersystem, 2,98 kw benzinmotor (honda), bediener- anwesenheitskontrolle, grasfänger, bremsen...

  • Page 35: Technische Daten    2

    Technische daten 2 7 2.5 gewicht ________________________________________________________________ gewicht (masse) pgm 22 ......85 kg mit fänger, walze, kippständer. 2.6 zubehÖr ________________________________________________________________ für eine vollständige liste von zubehör und zusatzgeräten ...

  • Page 36: 3    Warnschilder

    3 warnschilder 8 3 warnschilder 3.1 warnschilder __________________________________________________________ machen sie sich mit den hinweisschildern vertraut, da diese für den sicheren betrieb der maschine äußerst wichtig sind. BeschÄdigte hinweisschilder sollten unverzÜglich erneuert werden. ! Warn...

  • Page 37: Erste Inspektion    4

    Erste inspektion 4 9 4 erste i nspekti on 4.1 allgemeines ____________________________________________________________ einstellung und testen der maschine sollte immer von einem fachlich qualifizierten techniker durchgeführt werden, der mit dem betrieb dieser maschine vertraut ist. Jede anweisung vo...

  • Page 38: 5    Bedienungselemente

    5 bedienungselemente 10 5 bedienungselemente 5.1 symbole________________________________________________________________ 5.2 bedienungselemente ___________________________________________________ a. Parkbremse – ist stets dann zu verwenden, wenn der mäher unbeaufsichtigt gelassen wird oder als betri...

  • Page 39: Bedienungselemente    5

    Bedienungselemente 5 11 e. Trommelschalthebel – zum ausrücken den griff (e) nach unten drehen. Die kupplung stets ausrücken, wenn der mäher transportiert wird. F. Starterhebel –der starterhebel öffnet und schließt das drosselventil im vergaser. In der gesch- lossenen stellung wird die kraftstoffmisc...

  • Page 40: 6    Betrieb

    6 betrieb 12 6 betrieb 6.1 tÄgliche ÜberprÜfung _________________________________________________ 1. Eine sichtprüfung des gesamten geräts durchführen, auf abnutzungserscheinungen, lockere kleinteile sowie auf fehlende oder beschädigte teile achten. Auf undichtigkeiten im kraftstoffsystem oder Ölsys...

  • Page 41: Betrieb    6

    Betrieb 6 13 6.3 bedienungshinweise ____________________________________________________ 1. Der motor darf unter keinen umständen angelassen werden, wenn der bediener oder umstehende personen vor der haspel stehen. 2. Den motor nie in einem geschlossenen bereich laufen lassen. 3. Hände und füße von ...

  • Page 42: 6    Betrieb

    6 betrieb 14 6.4 anlassen/abstellen des motors _______________________________________ anlassen des motors 1. Den Öl- und kraftstoffpegel prüfen und dann den kraftstoffhahn (g) öffnen. 2. Den choke-hebel (f) in die “geschlossen"- position stellen. 3. Den zündschalter (d) in die “ein”-position stelle...

  • Page 43: Betrieb    6

    Betrieb 6 15 6.5 transportrÄder (optionales kit 62293) _________________________________ 1. Den kippständer gegen den boden drücken und fest-halten, dann den mähergriff zurückziehen, bis der mäher auf dem ständer (l) ruht. 2. Zum abnehmen der räder die halteklemme (j) von der nabe wegdrücken und das...

  • Page 44: 6    Betrieb

    6 betrieb 16 6.7 mÄhen __________________________________________________________________ 1. Den motor abstellen. Den mäher auf den kippständer stellen, um die transporträder abzunehmen (vgl. Abschnitt 6.5). 2. Den trommelschalthebel (e) einrücken und den mäher vom kippständer schieben. Den motor st...

  • Page 45: Betrieb    6

    Betrieb 6 17 6.8 tÄgliche wartung ______________________________________________________ 1. Den mäher auf einer flachen, ebenen fläche parken. Die feststellbremse anlegen und den motor abstellen. 2. Nach bedarf alle schmierpunkte einfetten oder schmieren. 3. Zur brandverhinderung den mäher nach jede...

  • Page 46: 7    Einstellungen

    7 einstellungen 18 7 einstellungen 7.1 allgemeines ___________________________________________________________ 1. Die einstellungen und wartungsarbeiten müssen immer von einem qualifizierten techniker durchgeführt werden. Wenn es nicht möglich ist, die richtige einstellung vorzunehmen, wenden sie si...

  • Page 47: Einstellungen    7

    Einstellungen 7 19 7.3 untermessers _________________________________________________________ 1. Abschnitt 7.2 lesen, bevor diese einstellung vorgenommen wird. 2. Mit den einstellungen an der vorderkante der trommel beginnen, mit der hinterkante weitermachen. Die vorderkante des trommelmessers ist j...

  • Page 48: 7    Einstellungen

    7 einstellungen 20 7.5 schnitthÖhe ___________________________________________________________ hinweis: darauf achten, daß das untermesser richtig eingestellt ist, bevor die schnitthöhe eingestellt wird (abschnitt 7.3). 1. Den kippständer nach unten drücken und den mäher am griff nach hinten kippen....

  • Page 49: Einstellungen    7

    Einstellungen 7 21 7.7 drehmomentdaten _____________________________________________________ jacobsen verwendet standardmäßig plattierte schrauben der festigkeitsklasse 5, wenn nicht anders angegeben. Beim anziehen plattierter schrauben ist der wert für geschmiert zu verwenden. Warnung alle drehmome...

  • Page 50: 8    Wartung

    8 wartung 22 8 wartung 8.1 allgemeines ___________________________________________________________ 1. Die einstellung und wartungsarbeiten müssen immer von einem qualifizierten techniker durchgeführt werden. Wenn keine ordnungs- gemäßen einstellungen vorgenommen werden können, wenden sie sich bitte ...

  • Page 51: Wartung    8

    Wartung 8 23 8.3 motorÖl________________________________________________________________ täglich vor dem starten des motors das maschinenöl prüfen. Ist der Ölstand zu niedrig, Öltankdeckel abnehmen und die erforderliche menge Öl nachfüllen. Nach den ersten 20 betriebsstunden einen ersten Ölwechsel d...

  • Page 52: 8    Wartung

    8 wartung 24 8.5 entfernen des bodenmesserbeschlags _______________________________ 1. Zum entfernen des beschlags (e) die mutter (a) lockern und die muttern (b) 1/4 drehung oder mehr gegen den uhrzeigersinn drehen, um das bodenmesser leicht mit den haspelmessern in kontakt zu bringen. 2. Die kleint...

  • Page 53: Wartung    8

    Wartung 8 25 8.8 radlager_______________________________________________________________ auf der lagerstirnfläche sind das wort „lock“ und ein pfeil eingeprägt. Beim austauschen des lagers unbedingt sicherstellen, daß es in der richtigen drehrichtung eingebaut wird. Beim rechten rad das lager so ein...

  • Page 54: 8    Wartung

    8 wartung 26 8.10 stÖrungssuche ________________________________________________________ vor einstellungen oder wartungsarbeiten den abschnitt zur wartung für vorgehensweisen und warnhinweise lesen. Symptome wahrscheinliche ursachen lösung motor springt nicht an startklappe in falscher stellung sieh...

  • Page 55: Wartung    8

    Wartung 8 27 8.11 schmierung ____________________________________________________________ der mäher wurde so entwickelt, dass er minimale schmierung erfordert. Überschmieren erzeugt eine hohe belastung von lagern und motor und mindert so die leistung der maschine. Alle wartungsintervalle müssen bei ...

  • Page 56: 9    Anmerkungen

    9 anmerkungen 28 9 anmerkungen.

  • Page 57

    1.1. . . . . . . . . . . . . . . . . . . Decals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ..2 2.1. . . . . . . . . . . . . . . . . . . Handle and controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 3.1. . . . . . . . . . . ...

  • Page 58: Pgm

    1 1 15 2 3 4 5 6 7 8 8 9 10 11 12 13 l wa 98 db 14 14 1. Slide bail to the left. To engage traction 2. Squeeze bail to handle. 16 16 pgm 1.1 decals serial no. All be sure the traction clutch lever is in neutral before starting the engine. Caution 1 reel clutch control engage disengage j-t-3001792 10...

  • Page 59: Pgm

    2 > change from previous revision pgm item part no. Qty. Description serial numbers/notes 1 362764 1 decal, caution 2 3001790 1 decal, caution 3 4125685 1 decal, pgm 22 4 2811102 1 decal, eu 5 340830 1 decal, spanish 6 361854 1 decal, caution 7 4127335 1 decal, danger 8 4131528 1 decal, noise 98 db ...

  • Page 60: Pgm

    3 a a b b c c 1 1 2 3 4 5 5 5 6 6 7 7 8 8 9 10 11 12 13 14 15 16 17 / 18 19 / 20 21 22 23 24 25 26 27 27 28 29 30 31 32 33 34 35 36 37 38 39 pgm 2.1 handle and controls serial no. All.

  • Page 61: Pgm

    4 > change from previous revision item part no. Qty. Description serial numbers/notes 1 366708 2 flanged bearing 2 400262 2 screw, 3/8-16 x 1” hex head 3 400268 1 screw, 3/8-16 x 1-3/4” hex head 4 434029 4 screw, 1/4-20 x 1” socket head 5 443102 7 nut, 1/4-20 hex 6 443110 2 nut, 3/8-16 hex 7 444718 ...

  • Page 62: Pgm

    5 8 9 10 11 18 4 3 4 5 6 7 18 20 1 2 19 20 12 13 14 15 16 17 pgm 3.1 left chain cover serial no. All.

  • Page 63: Pgm

    6 > change from previous revision pgm item part no. Qty. Description serial numbers/notes ●▲ 1 207480 1 cover, chain 2 472201 1 plug, 1/8 pipe,square head ◆ 3 400102 1 screw, 1/4-20 x 3/8” hex head 4 446130 4 lockwasher, 1/4 heavy 5 304756 1 retainer 6 503438 1 lever, shift 7 339910 1 • o-ring ◆ 8 4...

  • Page 64: Pgm

    7 17 8 7 37 36 23 24 21 20 18 34 24 39 35 33 32 22 31 31 30 30 26 27 5 2 15 16 38 25 6 13 12 14 1 28 29 19 5 4 11 10 9 40 3 pgm 4.1 left side frame serial no. All.

  • Page 65: Pgm

    8 > change from previous revision pgm item part no. Qty. Description serial numbers/notes ● 1 2811557 1 frame, l.H. 2 337677 1 • seal, oil 3 2811124 1 • stud, handle 4 336962 1 • seal, oil 5 500534 2 • bearing cup and cone 6 545940 2 • bushing 7 365753 1 • seal, grease 8 303490 1 • bearing 9 307959 ...

  • Page 66: Pgm

    9 8 9 6 5 1 2 4 7 21 13 20 19 18 3 4 10 11 12 13 14 15 16 17 pgm 5.1 right side frame serial no. All.

  • Page 67: Pgm

    10 > change from previous revision pgm item part no. Qty. Description serial numbers/notes 1 2811558 1 frame, r.H. 2 337677 1 • seal, oil 3 336962 1 • seal, oil 4 500534 2 • bearing cup and cone 5 2811124 1 • stud, handle 6 545940 1 • bushing 7 307377 1 spacer, shaft 8 471223 1 fitting, grease 9 471...

  • Page 68: Pgm

    11 38 39 34 31/33 36 1 20 22 12 23 18 19 11 8 13 39 3 4 12 22 21 35 16 37 15 14 6 7 4 3 5 30 16 9 2 27 40 29 28 26 17 25 24 32 10 503477 22" high profile 503478 22" low profile 503479 22" tournament 5002887 22" special tournament standard bedknife options 4131369 22" high profile 4131001 22" low pro...

  • Page 69: Pgm

    12 > change from previous revision pgm item part no. Qty. Description serial numbers/notes ●▲ 1 122544 1 cross bar, front 2 122545 1 cross bar, rear 3 400266 8 screw, 3/8-16 x 1-1/2” 4 446142 8 lockwasher, 3/8 heavy 5 304740 1 tie rod, front 6 443114 2 nut, 7/16-14 hex 7 446148 2 lockwasher, 7/16 8 ...

  • Page 70: Pgm

    13 1 2 3 4 5 6 7 8 9 10 11 11 12 13 14 31 15 17 18 21 23 29 24 25 26 19 throttle cable installation 20 22 part of engine part of engine 27 16 27 28 29 pgm 7.1 engine and clutch serial no. All.

  • Page 71: Pgm

    14 > change from previous revision pgm item part no. Qty. Description serial numbers/notes 1 303873 1 washer 2 309756 1 sprocket, 3 365658 4 spacer, engine mounting 4 400194 4 screw, 5/16-18 x 1-3/4” hex head 5 306369 1 screw, 5/16-24 x 1” hex head 6 434029 3 screw, 1/4-20 x 1” socket head 7 441677 ...

  • Page 72: Pgm

    15 10 8 7 4 2 3 1 6 5 21 20 5 6 3 2 4 7 9 11 12 8 13 14 15 16 15 11 17 18 19 pgm 8.1 traction rollers serial no. All.

  • Page 73: Pgm 22

    16 > change from previous revision item part no. Qty. Description serial numbers/notes 1 3004026 1 shaft, roller 2 163801 2 gear, differential 3 325656 2 • bushing 4 344745 2 washer, thrust 5 202947 2 pinion 6 308030 2 washer, pinion thrust 7 103862 2 housing, differential 8 308033 2 • bushing 9 403...

  • Page 74: Pgm

    17 17 14 15 12 13 10 20 21 11 5 5 3 18 19 23 16 2 3 1/4 6 7 8 9 22 22 pgm 9.1 transport wheels serial no. All.

  • Page 75: Pgm

    18 > change from previous revision pgm item part no. Qty. Description serial numbers/notes 1 1000477 1 hub, l.H. Wheel 2 338766 1 • bearing 3 366705 2 • seal 4 1000476 1 hub, r.H. Wheel (includes 2 and 3) 5 366697 4 bushing 6 366718 1 collar, latching 7 445801 1 nut, 5/8-18 hex jam lock 8 361451 1 w...

  • Page 78

    Textron golf, turf & specialty products po box 7708, charlotte, nc 28241-7708 www.Ttcsp.Com equipment fr om jacobsen is built to exacting standards ensured by iso 9001 and iso 14001 registration at all of our manufacturing locations. A worldwide dealer network and factory trained technicians backed ...