1. DL manuals
  2. Jacobsen
  3. Lawn Mower
  4. Greens King IV 62302
  5. Operation Manual

Jacobsen Greens King IV 62302 Operation Manual - Warning

Manual is about: with ROPS

Summary of Greens King IV 62302

  • Page 1

    Dealer manual warning warning: if incorrectly used, this machine can cause severe injury. Those who use and maintain this machine should be trained in its proper use, warned of its dangers, and must read the entire manual before attempting to set up, operate, adjust, or service the machine. Dealer t...

  • Page 2

    2 contents this manual contains safety and operating instructions for your new jacobsen machine. This manual should be stored with the equipment for reference during operation. Before you operate your machine, you and each operator you employ should read the manual carefully in its entirety. By foll...

  • Page 3: Warning

    Safety 1 3 1 safety 1.1 operating safety ______________________________________________________ 1. Safety is dependent upon the awareness, concern, and prudence of those who operate or service the equipment. Never allow minors to operate any equipment. 2. It is your responsibility to read this manua...

  • Page 4: Warning

    1 safety 4 1.2 important safety notes _______________________________________________ this safety alert symbol is used to alert you to potential hazards. Danger - indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. Warning - indicates a potentia...

  • Page 5: Warning

    Controls 2 5 2 controls 2.1 icons ___________________________________________________________________ warning never attempt to drive the mower unless you have read the safety and operation manual and know how to operate all controls correctly. Familiarize yourself with the icons shown above and what...

  • Page 6

    2 controls 6 2 1 n r ! Warning never mow in transport. If lever is in transport mode, forward motion will suddenly increase when mowers are raised or sut off do not use this machine on slopes greater than 12.5° . ! Warning 1. Read operators manual. Do not allow untrained operators to use this machin...

  • Page 7: Warning

    Controls 2 7 2.2 control descriptions __________________________________________________ a. Reel control levers - used to operate the cutting units. Push lever(s) forward for forward rotation. Pull lever(s) back for reverse rotation. All three levers must be in off position to start engine. B. Parki...

  • Page 8: Caution

    3 set-up 8 3 set-up 3.1 general ________________________________________________________________ the set-up and initial testing of the unit should always be performed by a trained technician, familiar with the operation of the equipment. Read each instruction completely and make sure you understand ...

  • Page 9

    Set-up 3 9 3.4 torsion springs ________________________________________________________ 1. Slide one clamp (f) over each lift arm and secure with 5/16-18 x 1-1/4” carriage bolt and 5/16-18 locknut (g and e). Do not tighten. 2. Slide the right (j) and left (h) torsion spring over their respective lif...

  • Page 10

    3 set-up 10 3.7 steering wheel ________________________________________________________ 1. Remove hex jam nut (r) from steering column. 2. Position the steering wheel over the shaft then reassemble the hex jam nut. Torque nut to 25-30 ft. Lb. (34-41nm) and install the steering wheel cap (s). Figure ...

  • Page 11

    Set-up 3 11 3.9 fuel hose routing______________________________________________________ gas units only 1. Remove temporary hose from fitting in top right corner of tank to rollover valve. 2. Assemble goose neck tube (ba) to right side rops tube using four clamps (bb) and #10-24 x 1/2” thread cutting...

  • Page 12: Warning

    3 set-up 12 3.12 operating checks ______________________________________________________ after the initial inspection and set-up of reels and accessories, test the tractor and implements for proper operation. 1. Test the interlock system. [section 3.13] 2. Start tractor and check that switches, gaug...

  • Page 13: Warning

    Adjustments 4 13 4 adjustments 4.1 general ________________________________________________________________ 1. Adjustments and maintenance should always be performed by a qualified technician. If proper adjustment cannot be made, contact an authorized jacobsen dealer. 2. Replace, do not adjust, worn...

  • Page 14: Caution

    4 adjustments 14 4.3 bedknife adjustment __________________________________________________ 1. Read section 4.2 before making the adjustment. 2. Start adjustment at the leading end of the reel, followed by the trailing end. The leading end of the reel blades is that end which passes over the bedknif...

  • Page 15

    Adjustments 4 15 4.5 reel bearing ___________________________________________________________ excessive end play or any radial play indicates bad bearings, a weak tension spring, or a backed off nut. 1. Check bearing housing mounting hardware. Tighten or replace components as required. Carefully cle...

  • Page 16: Warning

    4 adjustments 16 4.8 leveling procedure____________________________________________________ 1. Lower the implements until they are about 1/4 in. (6.35 mm) above the ground. If they are not level with the ground, adjust torsion spring (z). 2. Carefully loosen spring mounting clamp and slowly turn cla...

  • Page 17: Caution

    Adjustments 4 17 4.11 parking brake__________________________________________________________ disengage brake lever and measure the distance between nut (ab) and bottom of pivot. Adjust nut so the distance is 3/16 in. (5 mm). Figure 4m 4.12 interlock switches ________________________________________...

  • Page 18

    4 adjustments 18 4.14 traction lever _________________________________________________________ 1. Remove front cowling and adjust lever to align with the four positions on the instrument panel. 2. Adjust ball joints (ac) on rod (ad) and/or adjust position and number of washers (ae) for proper alignm...

  • Page 19

    Adjustments 4 19 4.17 choke control _________________________________________________________ 1. Push choke control knob to the off position. 2. Set choke lever at carburetor to off (butterfly open) position. 3. Adjust control wire (at the carburetor) then clamp wire housing in place while keeping c...

  • Page 20: Notice

    4 adjustments 20 4.19 torque specification___________________________________________________ jacobsen uses grade 5 bolts as standard, unless otherwise noted. Notice all torque values included in these charts are approximate and are for reference only. Use of these torque values is at your sole risk...

  • Page 21

    Troubleshooting 5 21 5 troubleshooting 5.1 general ________________________________________________________________ the troubleshooting chart below lists basic problems that may occur during start-up and operation. For more detailed information regarding the hydraulic and electrical systems contact ...

  • Page 22: Warning

    6 lubrication chart 22 6 lubrication chart 6.1 general ________________________________________________________________ 1. Always clean the grease fitting before and after lubricating. 2. Lubricate with grease that meets or exceeds nlgi grade 2 lb specifications. Apply grease with a manual grease gu...

  • Page 23

    Notes 7 23 7 notes.

  • Page 24

    7 notes 24.

  • Page 25

    Pre-delivery checklist mower _________________________ check: ❏ wheel lug torque 85 -95 ft. Lb. (115 - 128 n.M) ❏ tire pressure should be: ❏ 10 - 12 psi (0.69 - 0.83 bar) ❏ steering nut torque 25 - 30 ft. Lb. (34 - 51 n.M) ❏ traction pedal adjustment ❏ traction lever adjustment ❏ parking brake adjus...

  • Page 26

    Jacobsen, a textron company 11108 quality drive, charlotte, nc 28273 www.Jacobsen.Com 800-848-1636 when performance matters. ™ equipment from jacobsen is built to exacting standards ensured by iso 9001 and iso 14001 registration at all of our manufacturing locations. A worldwide dealer network and f...