1. DL manuals
  2. Jacobsen
  3. Lawn Mower
  4. HR600
  5. Quick Start Manual

Jacobsen HR600 Quick Start Manual - Note

Manual is about: Ride on Rotary Mower

Summary of HR600

  • Page 1

    A textron company quick start guide jacobsen hr600 and hr700 ride on rotary mower starting the engine seat adjustment controls driving mowing visual display refer to the safety, operation and maintenance manual for full operating instructions. 25130g-us (rev.0) rjl 100 january 2016.

  • Page 2

    Quick start guide en-2 ransomes jacobsen limited reserves the right to make design changes without obligation to make these changes on units previously sold and the information contained in this manual is subject to change without notice. © 2016 , ransomes jacobsen limited. All rights reserved.

  • Page 3: Starting The Engine

    Quick start guide en-3 1234.51234.5 12v 10a 1 2 3 4 .5 1 2 3 4 .5 1 2 3 4 .5 12v 1 0a 1234.5 1234.5 12v1 2 v 12v 10a a c d b e a c d b e before you operate for the first time • check and adjust tyre pressure, if necessary, see safety, operation and maintenance manual. • if necessary, add diesel fuel...

  • Page 4: Warning

    Quick start guide en-4 seat (grammer msg85) adjustments to the seat can be made for leg reach, backrest angle and operator weight to give a good position to operate the machine. A. Forward and backward adjustment to adjust the position of the adjusting lever (a) is on the right hand side of the seat...

  • Page 5: Steering Wheel Adjustment

    Quick start guide en-5 steering tilt control when the operators seat is in the correct position to operate the traction pedal comfortably. Push the small foot pedal (a) at the base of the steering column. Tilt the column backward or forward to the correct position. Release the small foot pedal to lo...

  • Page 6: Controls

    Quick start guide en-6 controls w x r y p t s q a e m b k c z 5 .6 5.5 l 1234.51 2 3 4 .5 1234.5 1 2v 10 a f d g j h 1234.5 1234.5 12v1 2 v e n b f d c z k 6.6 6.5 12v 10a l j m g a h h h a. Starter key switch. B. Throttle control. C. Parking brake switch. D. Transport lock switch. E. Cutter switch....

  • Page 7: Controls

    Quick start guide en-7 controls starter key switch turn the starter key to the right to start the engine. Release the key to return automatically to the 'on' position for normal operation. Note: before the engine starts, the glow plugs automatically preheat. The visual display shows the glow plug sy...

  • Page 8: Controls

    Quick start guide en-8 horn button for machines without the lighting kit. The horn button (a) is on the control panel. If the lighting kit is fitted, the horn is found on the end of the indicator stalk. Cutter switch to start to cut make sure the speed limiter is in mow position and the units are lo...

  • Page 9: Controls

    Quick start guide en-9 controls auxillary hydraulic services kit switch (optional) this switch sets the rotary brush or snow blade to a right side or a left side forward position. Push the top of the rocker switch to set a right side forward position. Push the bottom of the rocker switch to set a le...

  • Page 10: Controls

    Quick start guide en-10 controls a left turn signal b working lights switch (optional) c beacon switch d front screen de-mist switch e rear screen wiper switch (optional) f front screen wash switch g front screen wiper switch h right turn signal j fan control k air conditioning control l temperature...

  • Page 11: Note

    Quick start guide en-11 how to drive • set the throttle to maximum engine speed. • release the parking brake before you move in a forward or reverse direction. • forward - carefully press the top of the traction pedal to engage forward drive. • reverse - carefully press the bottom of the traction pe...

  • Page 12: Note

    Quick start guide en-12 how to mow 1. Release any transport locks and lower the cutting units with the joysticks. 2. To engage the cutting mechanism, press the upper half of the cutting unit switch, found on the control panel. 3. Release the parking brake and drive in a forward direction. 4. Set a s...

  • Page 13: Visual Display

    Quick start guide en-13 start up screen when the ignition key is turned to the start position, this screen is shown. The hour meter will show total hours of engine operation. Warning/service screen after the start up screen, the warning screen is shown. If the machine is within 5 hours of the next s...

  • Page 14: Visual Display

    Quick start guide en-14 engine start when the ignition key is turned to the start position, this screen is shown. If the parking brake is applied, the cutting unit switch is in the off position and the foot pedal is in the neutral position and when the operator is in the seat, the engine will start....

  • Page 15: Visual Display

    Quick start guide en-15 warning slope angle 25° if the slope angle reaches 25º the screen will display this warning indicating that at 25º the front cutter deck will be lifted 4- 6 inches above the ground to improve the stability and all decks will stop rotation. An audible warning will be given, th...

  • Page 16: Visual Display

    Quick start guide en-16 warning foot pedal fault when this screen is shown if there is a communications fault between the foot pedal and the controller. Stop the machine as soon as possible and contact your local ransomes jacobsen dealer when this fault occurs the machine go’s into limp-home mode. T...

  • Page 17: Visual Display

    Quick start guide en-17 warning service required when this screen is shown, the machine needs a service. Go to the main menu and select service menu, time until service to show the items needed for a service., the number in the top right of the screen indicates the total number of faults recorded. P...

  • Page 20

    Europe & rest of the world except north & south america ransomes jacobsen limited west road, ransomes europark, ipswich, ip3 9tt english company registration no. 1070731 www.Ransomesjacobsen.Com north & south america jacobsen, a textron company 11108 quality drive, charlotte, nc 28273, usa www.Jacob...