DL manuals
Jacto
Stairlifts
J600
Assembly Manual

Jacto J600 Assembly Manual

Page of 8

Download

Print this page

Bookmark us

03/23/05 J600CHT Assembly – DRAFT Prepared for Jacto

Service Seminar 3/2005

DRAFT COPY

J600 CHT Assembly

1) Remove the sprayer and components from the crate it was shipped in. In the crate

you will find the following components to assemble: main outlet duct, stationary

duct, control valve, vertical hydraulic cylinder and brackets, clean water tank and

bracket, side step, auxiliary ducts and JA nozzles, fan cage cover for disconnect, and

accessory box with the required fasteners to assembly the sprayer.

Accessory Box

The above picture shows the parts that you will find inside the accessory box. The

hardware will be used in the assembly of the sprayer. You will also notice that there

is 2 vertical cylinder brackets, pivot bushings for duct, pin for vertical cylinder, fan

disconnect cover, plate for attaching the fresh water tank bracket, 6 JA nozzles with

swirl cores, hose retaining clip, spanner wrench, and pins for your convenience when

attaching the sprayer to the tractor. You will also find the operator’s manual.

1 2 3 4 5 6 7 Next › »

Summary of J600

Page 1
03/23/05 j600cht assembly – draft prepared for jacto service seminar 3/2005 draft copy j600 cht assembly 1) remove the sprayer and components from the crate it was shipped in. In the crate you will find the following components to assemble: main outlet duct, stationary duct, control valve, vertical ...
Page 2: Control Valve
03/23/05 j600cht assembly – draft prepared for jacto service seminar 3/2005 draft copy control valve 1) install control valve into bracket (make sure hoses are routed on top of the tank towards the center) as shown below. Install the blue return hoses and clamps to the control valve. Note the hose c...
Page 3
03/23/05 j600cht assembly – draft prepared for jacto service seminar 3/2005 draft copy stationary duct assembly 1) install the stationary duct on the top of the fan housing. It is recommended the 4 bolts that attach the stationary duct to the frame be installed first to help align the other 12 holes...
Page 4
03/23/05 j600cht assembly – draft prepared for jacto service seminar 3/2005 draft copy movable duct assembly 1) position the upper duct onto the stationary duct with the duct facing towards the rear of the sprayer. Align the two holes in the duct with the bushing holes in the stationary duct and ins...
Page 5
03/23/05 j600cht assembly – draft prepared for jacto service seminar 3/2005 draft copy hydraulic cylinder assembly 1) install the vertical hydraulic cylinder to the movable duct by first installing the pin that attaches it to the stationary duct. Next install the two brackets with the pins on the cy...
Page 6
03/23/05 j600cht assembly – draft prepared for jacto service seminar 3/2005 draft copy auxiliary duct assembly 1) install the two auxiliary ducts onto the movable duct with clamps as shown below. Next install the hoses that connect to the main duct nozzle and auxiliary duct nozzles and tighten the h...
Page 7
03/23/05 j600cht assembly – draft prepared for jacto service seminar 3/2005 draft copy pto shaft and clean water tank 1) install the pto shaft by sliding the implement end over the drive shaft and aligning the key way with the key. Install the retaining bolt and tighten. 2) install the clean water t...
Page 8
03/23/05 j600cht assembly – draft prepared for jacto service seminar 3/2005 draft copy final assembly and setup tips 1) install the side step to the holes located on the left lower portion of the frame using the three bolts supplied. 2) install the center piece for the fan cage for the fan disconnec...