- DL manuals
- Jacuzzi
- Outdoor Shower
- BZ00000
- Installation And Operating Instructions Manual
Jacuzzi BZ00000 Installation And Operating Instructions Manual
Summary of BZ00000
Page 1
Summer rain ™ ii 2 person shower system two wall and three wall installation and operating instructions jacuzzi whirlpool bath © bz00000 03/05.
Page 2
Note: this is a professional grade product. A knowledge of construction techniques, plumbing and electrical installation according to codes are required for proper installation and user satisfaction. We recommend that a licensed contractor perform the installation of all jacuzzi whirlpool bath © pro...
Page 3: Contents
Contents specifications _________________________________________________________________________ 2 enclosure specifications ________________________________________________________________ 3 rough-in reference ____________________________________________________________________ 3 component identifi...
Page 4
Important: read complete instructions before beginning installation. Each unit arrives ready for installation, equipped with base, glass and associated hardware. Remove the unit from the carton. Retain the shipping carton until satisfactory inspection of the product has been made. Immediately upon r...
Page 5
Rough-in reference shown is 2 wall left hand base. Right hand opposite. The 3 wall base has tile flange on both sides and back. Enclosure specifications 48" 27-11/16" top view 72" 38-15/16" 36" 1" tile flange blower motor for units with air air line for units with air 84" 72" 48" front view side vie...
Page 6
Component identification front view side view (2 wall only ) glass side panel glass doors rail bracket and cover cap (2 wall only) (2 wall only) side support rail center support rail air tower water tower seat base door post door post water tower wall post (2 wall only) wall rail wall post and jamb ...
Page 7
Preliminary rough-in the floor structure beneath the unit must be able to support a total weight of the unit and bather(s). Refer to page 2, specifications, for weight speci- fications. Refer to component identification on page 4 to help identify parts. Step 1 provide an opening in the subfloor no l...
Page 8
Step 6 with a large screwdriver and the tool included with the drain, tighten the inside compression nut to seal the drain pipe connection. After drain is fully installed, test for proper drainage. If the shower base does not drain properly, rectify this condition before proceeding with the installa...
Page 9
Clean up after base installation to avoid dulling and scratching the acrylic surface of the base, never use abrasive cleaners. A mild liquid detergent and warm water clean soiled surfaces. Remove spilled plaster with a wood or plastic edge. Metal tools scratch the surface. Spots left by plaster or g...
Page 10
Towers and doors installation these instructions are for summer rain ii 2 wall and 3 wall units with and without air feature option. Refer to component identification on page 4 to help identify parts. Step 1 on the 2 wall unit attach the wall jamb to the water tower adjacent to the side wall. Then i...
Page 11
Towers and doors installation step 4 place the center support rail into slot on each tower. If rail does not readily fit into slots, it may be necessary to loosen the bolts holding towers to base (it may only be necessary to loosen one tower). Do not force center rail into slots. With center support...
Page 12
Towers and doors installation 10 jacuzzi whirlpool bath © bz00000 03/05 grout stud shim if necessary do not fill cement board tile silicone sealant 1-1/8" maximum no minimum shower base caulking tile cement board tile adhesive stud flange shim if necessary to fill gaps between stud and flange stud 1...
Page 13
Step 9 (2 wall only) place the side support rail into the slot on the water tower. Place the short wall rail into the slot on the other water tower. Rotate flat end of short wall rail flush to wall. With rails in position install hold down brackets, but do not tighten screws. Check water towers for ...
Page 14
Step 10 two shut-off valves are provided per water tower. To hook up supply lines, unscrew valves from braided line. Using thread sealant, screw each valve to stub out at bottom of tower. Then reconnect braided line using provided gasket. Do not twist or kink supply lines when connecting. Perform th...
Page 15
Towers and doors installation step 12 move the door assembly to the door post on water tower and slide the assembly into the door post. Locate the base of the door into the slot of serrated door positioner that positions the hinge barrel as shown. Bottom of door frame hinge barrel shower base water ...
Page 16
Towers and doors installation finish wall edge of base glass side panel mounted parallel to edge of base wall post tape (3) screws (3) step 15 (2 wall only) position the fixed glass wall post so that the glass side panel will be parallel with the outside edge of the base. The fixed glass wall post p...
Page 17
Tower and door installation step 18 (2 wall only) align the glass with glass jamb and insert. Wall post glass glazing gasket inside of enclosure apply sealant jamb glass glazing gasket inside of enclosure apply sealant step 19 (2 wall only) install glazing gasket on fixed glass wall post and jambs o...
Page 18
Step 23 install handles as shown. Note orientation of handle. Hand tighten knob. Flat screw has a screw driver notch. Do not over tighten either knob or flat screw as cracked glass may result. Glass door washers large washer interior of shower door hinge tower cover insert this side first tower cove...
Page 19
Towers and door installation step 26 seal all around all bases of towers with sealant. Also seal the inside of wall posts, jambs, door posts, tile joint to wall post, and bottom of glass side panel on the inside only. Clean up after towers and door installation to avoid dulling and scratching the to...
Page 20: Shower Towers
Operation shower towers 18 jacuzzi whirlpool bath © bz00000 03/05 shower head there are three selectable positions: jet, normal pul- sating, and aerated flow. Body sprays (2 upper and 2 lower) to adjust the flow and intensity, turn as shown. The spray can also be turned to change the direction of th...
Page 21
Operation controller to turn on press on/off button or turn on water at either shower tower. The unit will then automatically go into a preheat cycle to heat the air transmission pipes. There will be a 5 (five) minute pause while the system preheats. During this time both leds will be on. When ready...
Page 22
To remove any lime scale from the shower head and body sprays, rub with your finger the outer ring of nozzles on the shower head and all nozzles on the body spray. To clean the foot temperature tester, unscrew the nozzle and back flush the wire mesh filter. Do not use metal tools (such as scissors o...
Page 23
Tower fixtures repair parts 21 jacuzzi whirlpool bath © bz00000 03/05 tower assembly washer (part of d709827) 4 6 9 (5x) 10 11 (4x) 13 14 15 16 17 18 19 3 (5x) 2 (5x) 1 (5x) 8 5 12 part of d709827 7 (part of u547000) 1. C546000 lock nut, 1/2" npt wp (5x) 2. G559000 ring compression ss (5x) 3. G56000...
Page 24
Tower plumbing repair parts 1 11 4 5 4 7 10 6 14 12 13 5 4 16 11 2 8 2 3 2 3 3 17 15 9 18 19 18 18 18 item no. Qty. Part no. Description 1 1 y221000 tower, 2 person shower 2 3 u401000 ftg, ell, .50" fst x 10 mm barb 3 4 y724000 1/2" elbow, slip x thread, sch 40 4 3 7164000 ell, street, .50", 90 o 5 ...
Page 25
23 jacuzzi whirlpool bath © bz00000 03/05.
Page 26
Printed in u.S.A . Jacuzzi whirlpool bath © bz00000 03/05 printed on recycled paper jacuzzi whirlpool bath national headquarters p.O. Box 702168, dallas, tx 75370-2168 service support: (800) 288-4002 product specifications are subject to change without notice. Use installation instructions supplied ...
Page 27
Jacuzzi whirlpool bath p.O. Box 702168 dallas, tx 75370-2168 warranty coverage jacuzzi whirlpool bath (the “company”) offers the following express limited warranty to the original purchaser of any jacuzzi whirlpool bath designer collection bath product (“unit”) who purchases the product for personal...
Page 28
Responsibilities of others inspecting the unit prior to installation is the responsibility of the installer or building contractor who acts on behalf of the user. They are responsible for ensuring the unit is free of defect or damage. Notices are placed on and in the unit and on the shipping carton ...