1. DL manuals
  2. Jacuzzi
  3. Kitchen & Bath Fixtures
  4. J-DREAM II
  5. Owner's Manual

Jacuzzi J-DREAM II Owner's Manual

Manual is about: Shower system

Summary of J-DREAM II

  • Page 1

    J-dream ii shower system owner’s manual assembly, installation & operating instructions tm.

  • Page 2: Owner'S Record

    Important safety information read all installation instructions save these instructions for future use. Owner's record jacuzzi whirlpool bath does not recommend prolonged periods of use of the steamer. Prolonged use of the steam system can raise the internal human body temperature excessively and im...

  • Page 3: Contents

    Part i assembly & installation specifications _______________________________________________________________________ 2 general information __________________________________________________________________ 3-4 packaging __________________________________________________________________________ 5 ha...

  • Page 4: J-Dream II Owner'S Manual

    Whirlpool bath r j-dream ii owner's manual front view product specifications are subject to change without notice. Specifications 2 top view dimensions 60" (1524mm)l 42" (1067mm)w 83" (2108mm)h total weight/ floor loading 833 lb (379 kg) 47.6 lb/ft 2 (233 kg/m 2 ) required water supply 6 gpm (23 lit...

  • Page 5: Room Construction: Important

    Read all instructions before beginning assembly and installation. General assembly information the j-dream ii shower unit is installed into a niche with the drain towards the left hand side of the unit as you face the shower door. This manual details the assembly, installation and operation. After t...

  • Page 6: Electrical Requirements

    Electrical requirements your j-dream ii, as it comes from the factory, requires a gfci protected 240 vac 3- wire 20 amp 50-60 hz circuit (2 conductor with ground) for single (1) phase electrical service, and must be in a separate circuit having no other appliance connected in that circuit. If you do...

  • Page 7: J-Dream II Packaging

    J-dream ii packaging 6 cartons packed together on a wooden crate. Contents of cartons: • wall panels • door frame • base/cover (includes product accessory pack and owners manual) • back wall • seat wall • equipment/seat wall 5 j-dream ii owner's manual.

  • Page 8: J-Dream II Owner'S Manual

    J-dream ii owner's manual letters (a) are used in the illustrations of the assembly procedure. 6 flat washer 1/4" pan head screw #10-24 x 3/4" lock nut 10-24 c washer screw b nut d flat head screw m4x10mm screw e pan head screw #12 x 1/2 screw f hex bolt 1/4-20 x 1.5" bolt g self-tapping m6x50mm bol...

  • Page 9: Rough-In

    7 rough-in washing machine outlet box connect #8 gauge (10mm2) minimum solid copper bond wire to the house electrical panel or approved local ground. An approved ground may be an 8 foot long ground rod (3 meter long earth rod), a plate electrode, or other acceptable bond. Check your local building c...

  • Page 10: J-Dream II Owner'S Manual

    8 locate base to provide assembly access to all sides remove base from carton labeled base/top. Place clear top in carton to prevent damage. (the clear top will not be installed until the unit has been fully assembled and plumbed). Position the j-dream base on the floor so that you have work access ...

  • Page 11: Drain Fitting

    9 drain fitting (provided with unit) leave enough flexibility in the waste line to allow the end of the stub-out to be blocked temporarily in a position under flush with the floor surface. This will allow the shower unit to slide across the floor into position without having to lift the shower unit....

  • Page 12: Attach Seat Walls to Base

    10 attach seat walls to base (j-dream ii with stereo shown) bolts (8) nuts (8) g j align four holes on seat wall frame over base and insert bolts and tighten nuts from underneath. Washers (8) i equipment seat wall non-equipment seat wall j-dream ii owner's manual.

  • Page 13: J-Dream II Owner'S Manual

    11 attach panel #2 to seat wall frame slide in panel feeding between frame and edge of seat wall. Align to frame and fasten panel to frame. Important: do not caulk panel to seat wall as the seat wall is hinged and designed to swing open. F screw (4) c washer (4) top view move frame seat wall seals w...

  • Page 14: J-Dream II Owner'S Manual

    12 attach panel #3 to seat wall frame slide in panel feeding between frame and edge of seat wall. Align to frame and fasten panel to frame. Important: do not caulk panel to seat wall as the seat wall is hinged and designed to swing open. Top view move frame seat wall c washer (4) f screw (4) seals p...

  • Page 15: Install Back Wall

    13 install back wall caulk the bottom and sides of back wall where indicated in the illustrations below. Install fasteners. Now align the back wall parallel to the pan lip to center the back wall between the seat walls. Screw (4) b washer (8) c nut (4) d caulk a a screw (4) b b caulk washer (8) c nu...

  • Page 16: J-Dream II Owner'S Manual

    B a a. Caulk washer (10) c nut (3) d screw (3) b b reinstall bolts (4) and washers (4) removed from seat wall and bracket seat wall attaches to panel #1 and #4 in three places. Seat wall attaches to panel #1 and #4 in two places. Caulk narrow side of panel faces toward the front panel #1 panel #4 14...

  • Page 17: J-Dream II Owner'S Manual

    15 attach brackets to seat wall frames and l bracket to left angle bracket j-dream ii owner's manual b b a c a 17" 58-3/8" to p o f frame screw (2) note: only the left side has this l bracket installed. Angle bracket with velcro ® strips k washer (2) d nut (2) b c l bracket u-clip a b screw (2) bolt...

  • Page 18: J-Dream II Owner'S Manual

    Caulk b screw (3) c washer (3) nut (3) d top view (right side) notch side view (right side) b screw (3) c washer (3) nut (3) d top view (left side) side view (left side) notch caulk 16 attach painted angle brackets to panels #1 and #4 note that each angle bracket has a notch on the top and bottom. T...

  • Page 19: J-Dream II Owner'S Manual

    17 attach door frame to angle brackets and base frame before proceeding, make sure the seat walls are closed and fastened. See detail b on page 15. Align door frame over tabs on base frame and pan lip. Pan lip is to fit into corner posts of door frame. Align holes along sides of door frame with angl...

  • Page 20: J-Dream II Owner'S Manual

    18 attach top frame to door frame, back wall and seat wall frames press/tap top frame into door frame, aligning notch in door frame with corner of top of frame while aligning with corners of enclosure. Frame snaps down into door frame and back snaps over back wall. Install bolts (4) through top fram...

  • Page 21: J-Dream II Owner'S Manual

    19 feed the four hoses and controller cable from the back wall and connect them as shown. The steam hose connection uses a hose clamp while the other hoses use spring clamps that are on the hoses. Also feed the cd/radio wire bundle to the back wall. (j-dream ii with stereo only.) j-dream ii owner's ...

  • Page 22: J-Dream II Owner'S Manual

    20 j-dream ii owner's manual use cable ties to attach the cd/radio wire bundle to the cascade hose. The hoses from valves 1 and 3 and the steam hose are loosely attached to their mounting brackets to allow the slack when connecting them and when the hinged seat wall is swung open (like a door) to ac...

  • Page 23: J-Dream II Owner'S Manual

    21 connect the hoses routed from the back wall as below (grayed lines are pre-attached). Connect the controller line. The red and black leads in the cd/radio wire bundle must be hooked up to the corresponding colored leads of the power supply. Connect the speaker leads. Connect the two steampro powe...

  • Page 24: Bonding

    22 bonding (top left hand side of right hand equipment seat wall) j-dream ii owner's manual connect a #8 guage (10mm2) minimum solid copper bond wire to the house electrical pannel or an approved local ground. An approved ground may be an 8 foot long ground rod (3 meter long earth rod), a plate elec...

  • Page 25: J-Dream II Owner'S Manual

    1. Make sure electric power is off at main breaker. 2. Static test water supply hoses for leaks. 3. Plug power cord into gfci protected wall outlet. 4. Move the assembled j-dream ii into final position. 5. Connect 2" shower drain (see page 9). 6. Adjust the levelling screws in the j-dream ii base fe...

  • Page 26: Attach Front Panels to Unit

    24 attach front panels to unit remove this screw before operation ground wire speaker and power leads b antenna wire rear view of cd/radio screw (2) tinnerman ® nuts (pre-installed) front panel b c d d front panel velcro ® screw (2) l important: attach cd/radio ground wire here velcro ® b a a c fram...

  • Page 27: J-Dream II Owner'S Manual

    25 place cover on top of unit. Align notch in cover with the corresponding notch in the top metal frame. J-dream ii owner's manual top cover.

  • Page 28: J-Dream II Owner'S Manual

    26 turn on electric power at main breaker operate unit and check for leaks attach bottom front panel to unit enclosure base frame panel velcro ® velcro ® removable face panels use finishing strip material (not provided) to cover gap between j-dream ii and finshed wall. Do not attach finishing strips...

  • Page 29

    27 figure 1. Control panel and display figure 2. Mixer control part ii: operating instructions control panel system control is provided by the electronic display located inside the shower cabin (see figure 1) the display is used to start up the five functions of the unit: the shower, the cascade wat...

  • Page 30: Maintenance

    Starting the hydromassage the j-dream allows you to enjoy the benefits of a real hydromassage. The hydromassage is created by the combined action of 16 water jets (four sets of 4 ). The action of each group of jets is either alternated or pulsed. To start the hydromassage jets, press the jets button...

  • Page 31

    29 care and maintenance of steampros maintenance of the steampros includes flushing and visually inspecting for water leaks. To flush the units: 1. Turn off power to the unit. 2. To gain access to the steampros, the seat wall (equipment wall) must be swung open. To do so, remove the three screws fro...

  • Page 32

    Printed in the u.S.A. Printed on recycled paper product specifications are subject to change without notice. Use installation instructions supplied with product. ©1997 jacuzzi whirlpool bath k922000 8/13/04 jacuzzi whirlpool bath p.O. Box 702168, dallas, tx 75370-2168 service support: call (800) 288...

  • Page 33

    31.

  • Page 34

    32.

  • Page 35: Shower System Product

    Jacuzzi whirlpool bath limited warranty shower system product warranty coverage jacuzzi whirlpool bath (the “company”) offers the following express limited warranty to the original purchaser of any jacuzzi whirlpool bath shower system product (“unit”) who purchases the product for personal or single...

  • Page 36

    Responsibilities of others inspecting the unit prior to installation is the responsibility of the installer or building contractor who acts on behalf of the user. They are responsible for ensuring the unit is free of defect or damage. Notices are placed on and in the unit and on the shipping carton ...