- DL manuals
- Jacuzzi
- Hot Tub
- J - LX
- Owner's Manual
Jacuzzi J - LX Owner's Manual
Summary of J - LX
Page 1
Owner’s manual l x ™ c o l l e c t i o n j - lx j - lxl 6530-542z rev. A.
Page 2: Attention New Spa Owner!
Attention new spa owner! Congratulations on the purchase of your new jacuzzi® spa! The following is a list of automated functions performed by your spa. These functions are listed below in an attempt to alleviate any operational concerns you may have during the first 24 hours of ownership! Also list...
Page 3: Lx Collection
Lx collection table of contents 1.0 important spa owner information ...................................1 2.0 fcc notice ........................................................................1 3.0 important safety instructions for all spa owners .........2 3.1 entrapment risk .........................
Page 4: Lx Collection
Lx collection 12.0 spa maintenance ............................................................35 12.1 cleaning the filters ................................................................... 35 12.2 draining and refilling ................................................................. 38 12.3 pil...
Page 5: Lx Collection
1 lx collection 1.0 important spa owner information your jacuzzi spa is constructed to the highest standards and is capable of providing many years of trouble-free use. However, because heat retentive materials are utilized to insulate the spa for efficient operation, an uncovered spa surface and wa...
Page 6: Lx Collection
2 lx collection 3.0 important safety instructions for all spa owners read and follow all instructions carefully! This spa was manufactured to meet the standards and specifications outlined in the “virginia graeme baker pool and spa safety act” (vgb safety act). When installing and using this spa, ba...
Page 7: Lx Collection
3 lx collection • a grounding wire connector is provided on this unit to connect a minimum no. 8 awg (8.4 mm²) solid copper conductor between this unit and any metal equipment, metal enclosures of electrical equipment, metal water pipe, or conduit within 5 feet (1.5m) of the unit. • never permit any...
Page 8: Lx Collection
4 lx collection 6. ! Warning: risk of severe injury or death! • since excessive water temperatures have a high potential for causing fetal damage during the early months of pregnancy, if pregnant or possibly pregnant, consult your physician before using a spa. • pregnant or possibly pregnant women s...
Page 9: Lx Collection
5 lx collection 9. ! Warning: in addition to maintenance of filters and water chemistry, proper ventilation is recommended to reduce the risk of contracting a waterborne illness (e.G. An infection, bacteria or virus) and/or respiratory ailments that could be present in the air or water. Consult a li...
Page 10: Lx Collection
6 lx collection 3.1 entrapment risk the consumer products safety commission/usa has reported that users of pools and spas have become entrapped (stuck) to drain and/or suction fittings causing death, drowning, or serious injury (see diagram below). This spa was manufactured to meet the standards and...
Page 11: Lx Collection
7 lx collection 3. ! Danger: risk of severe injury or drowning! Body entrapment: may occur when part of the torso becomes entrapped, inserted or sucked into a suction or outlet opening. • never allow children to play or get near the suction fittings, suction covers, filter, filter lid or skimmer ass...
Page 12: Lx Collection
8 lx collection 3.3 important additional csa safety instructions (canada only) when using this electrical equipment, basic safety precautions should always be followed, including the following: 1. Read and follow all instructions. 2. A green colored terminal or a terminal marked g, gr, ground, groun...
Page 13: Lx Collection
9 lx collection 4.0 choosing a location warning: for spas that are to rest on balconies, roofs or other platforms not specifically tied into main structural support, consult a professional structural en- gineer with experience in this type of application. ! The spa must be installed in such a manner...
Page 14: Lx Collection
10 lx collection 4.1 outdoor location in selecting the ideal outdoor location for your spa, we suggest that you take into consideration: • the proximity to changing area and shelter (especially in colder weather). • the pathway to and from your spa (this should be free of debris so that dirt and lea...
Page 15: Lx Collection
11 lx collection and can handle the entire contents of the spa. Be sure to make provisions for ceilings and other structures that may be below the spas installation. Areas around your spa can become wet or moist so all flooring and subsequent furniture, walls and adjacent structures should be able t...
Page 16: Lx Collection
12 lx collection 6.0 power requirements jacuzzi spas are designed to provide optimum performance and flexibility of use when connected to the maximum electrical service listed below. Minor circuit board modifications can be performed to allow your new spa to accept an electrical service other than t...
Page 17: Lx Collection
13 lx collection 7.0 electrical wiring instructions important notice: the electrical wiring of this spa must meet the requirements of the national electrical code/usa (nec) and any applicable state or local codes. The electrical circuit must be installed by a qualified electrician and approved by a ...
Page 18: Lx Collection
14 lx collection 8. Select the power supply inlet you want to use (figure a). Feed power cable to control box, then install it through the large opening provided in the bottom side of the box. 9. Connect wires, color to color, on terminal blocks tb1 and tb3 (figure c, page 15). Tighten securely! All...
Page 19: Lx Collection
15 lx collection blk red red red blk blk 1 2 figure c tb1 to circuit board power in green tb3 1 2 blue blue brown brown figure d tb1 tb2 to circuit board power in green tb3 north american 240v models: 240 vac, 3-wire connection 60 hz all export models: 230 vac, 3-wire connection 50 hz 8.0 spa fill u...
Page 20: Lx Collection
16 lx collection important: always fill your spa through the filter bucket after draining. Failure to do so may cause air to be trapped in either pump, preventing the pump from circulating water. Remove the hose and replace the filter cartridge. Note: do not overtighten filter cartridge, finger tigh...
Page 21: Lx Collection
17 lx collection cooler ( ) or warmer ( ) within 5 seconds. The set temperature increases or decreases by one degree each time one of these buttons is pressed. • the heater will turn off when the temperature corresponding to the thermostat setting is achieved. Important heater details: • the maximum...
Page 22: Lx Collection
18 lx collection water fill volume by model spa model average fill volume* sodium dichlor j-lx 360 gal (1,363 l) 9.0 oz j-lxl 370 gal (1,401 l) 9.3 oz *use average fill volume for chemical maintenance 10. Leave spa cover open during this step to allow excessive chemical vapors to exit spa, protectin...
Page 23: Lx Collection
19 lx collection 14. Turn on jet pumps when adding chemicals to ensure proper mixing and leave your hot tub cover open until the sanitizer level becomes stable to protect pillows and plastic knobs from chemical attack. Refer to the inside cover of the manual. Warning: risk of personal injury. • to d...
Page 24: Lx Collection
20 lx collection 9.0 control functions 9.1 control panel a. Led display: can display current water temperature (default display), water temperature set point, selected filtration/heating mode, and error messages. B. Warmer () button: increases water temperature set point. C. Cooler () button: decrea...
Page 25: Lx Collection
21 lx collection 9.2 j-lxl general spa features and controls 1 + _ 2 12 12 2 2 2 1 10 10 10 10 9 11 11 11 11 8 13 13 13 5 5 3 4 18 5 6 18 18 18 14 14 14 14 14 14 14 14 15 15 15 15 16 19 16 16 16 17 7 1. Control panel 2. Toggle air controls (3) 3. Filter/skimmer grill 4. Powerpro mx2 footwell jets (2...
Page 26: Lx Collection
22 lx collection 9.3 j-lxl air controls diagram air control operation rotate air controls 1-3 to add air to designated jet groups. 1 + _ 2 2 2 2 1 1 1 1 3 3 3 3 2 3 3 specifications/features subject to change without notice..
Page 27: Lx Collection
23 lx collection 9.4 j-lxl massage/waterfall selector diagram massage selector operation rotate massage selector 1 to divert water between designated jet groups. 1 + _ 2 2 2 2 1a 1b 1a 1 1b 1a 1b 3 3 b 1a 1a a massage selectors (1) • massage selector #1 controls pump #1. Jets (2) • these jets are al...
Page 28: Lx Collection
24 lx collection 9.5 j-lx general spa features and controls 1 + _ 2 12 12 2 2 2 1 10 10 9 11 11 11 11 8 13 13 5 5 3 4 18 5 6 18 18 18 12 14 14 14 14 14 14 15 15 15 15 16 19 16 16 16 17 7 2 5 1. Control panel 2. Toggle air controls (4) 3. Filter/skimmer grill 4. Powerpro mx2 jets (2) 5. Pillows (4) 6...
Page 29: Lx Collection
25 lx collection 9.6 j-lx air controls diagram air control operation rotate air controls 1-4 to add air to designated jet groups. 1 + _ 2 2 2 2 1 1 1 1 1 3 4 3 3 4 2 4 specifications/features subject to change without notice..
Page 30: Lx Collection
26 lx collection 9.7 j-lx massage/waterfall selector diagram massage selector operation rotate massage selector 1 to divert water between designated jet groups. 1 + _ 2 2 2 2 2 1a 1 1b 3 3 1b 1a 1a b 2 a 2 massage selectors (1) • massage selector #1 controls pump #1. Jets (2) • these jets are always...
Page 31: Lx Collection
27 lx collection 10.0 operating instructions the spa control system has automatic functions that operate upon start-up and normal operation to protect the system. Upon power up, the readout displays the following information: 1. Control panel displays current software release (e.G. 3.60), then; 2. C...
Page 32: Lx Collection
28 lx collection 10.2 activate jet pumps the control panel jets 1 button activates jets pump 1. The first press activates low speed, the second press activates high speed, and the third press shuts jets pump 1 off. The jets 2 button activates jets pump 2. The first press activates high speed, the se...
Page 33: Lx Collection
29 lx collection 10.5 jets the water flow through individual jets in your spa can be adjusted or turned off by rotating the outside jet ring. Some jets offer an adjustable center nozzle that allows you to change the water discharge angle. Simply tilt the center nozzle in these jets to the desired an...
Page 34: Lx Collection
30 lx collection 11.0 automatic filtration cycles your new spa includes an 8-hour circulation pump which filters the water continuously. The circulation pump draws water through the skimmer bag and one of two filter cartridges to effectively remove small debris in your spa. Note: the 8-hour circulat...
Page 35: Lx Collection
31 lx collection standard filtration/heating modes f0 5 minutes of filtration per day (one 5 minute “blow-out” cycle every 24 hours to purge all plumbing lines) f1 1 hour of filtration per day (one 30-minute cycle every 12 hours); this is the factory default setting. F2 1.5 hours of filtration per d...
Page 36: Lx Collection
32 lx collection 11.5 programming the circulation pump filtration cycle press and hold the jets pump 1 ( 1 ) and cooler ( ) button at the same time for 3 seconds to access the circulation pump programming. Once you have entered the circulation pump filtration cycle, continually press the warmer ( ) ...
Page 37: Lx Collection
33 lx collection 11.6 programming the clearray® (ultraviolet) water purification system a. Programming the clearray system (u) or corona discharge ozone (o3) press and hold the jets pump 1 ( 1 ) and cooler ( ) button at the same time for 3 seconds. Scroll pass the circulation pump programming menus ...
Page 38: Lx Collection
34 lx collection b. Resetting the duration countdown timer (clearray® system only) once the duration countdown timer for the clear ray system has reached zero, you will need to reset it, replace the uv bulb and clean the quartz tube. To reset the duration countdown timer: press press press press pre...
Page 39: Lx Collection
35 lx collection 12.0 spa maintenance proper and regular maintenance of your spa will help it retain its beauty and performance. Your authorized jacuzzi dealer can supply you with all the information, supplies, and accessory products you will need to accomplish this. Danger: risk of severe injury or...
Page 40: Lx Collection
36 lx collection an optional chemical feeder is available through your authorized jacuzzi dealer that installs under the filter cap (#2472-673). Always remove the chemical feeder cap and feeder (when used) during the filter cleaning process by turning the cap handle counterclockwise. Reinstall the c...
Page 41: Lx Collection
37 lx collection e lift unthreaded filter cartridge from skimmer well. F if used, remove the chemical feeder as instructed prior to rinsing the filter cartridges. Rinse debris from filter pleats on each cartridge using a garden hose and high pressure nozzle. Start at the top and work downward toward...
Page 42: Lx Collection
38 lx collection periodically, the filter cartridge will need a more thorough cleaning to remove imbedded oils and minerals. For this, we suggest cleaning as illustrated followed by soaking the filter overnight in a plastic container filled with a solution of water and specially formulated filter cl...
Page 43: Lx Collection
39 lx collection 12.3 pillow care remove and clean the headrest pillows as needed with soapy water using a cloth or soft-bristle brush. Always remove the pillows when adding chemical shock treatment to the spa water. The pillows can be returned to the spa when the sanitizer reading is stable as reco...
Page 44: Lx Collection
40 lx collection b. Sunbrella® cover maintenance to clean and condition the sunbrella cover: 1. Brush off dirt, leaves and any loose debris. 2. Thoroughly hose down the cover. 3. Using a large sponge or a soft bristle brush, use diluted or mild soap (such as woolite or dreft, no detergents) and scru...
Page 45: Lx Collection
41 lx collection small scratches or nicks resulting in the lighter colored sub surface being exposed can be made less obvious by using common furniture repair markers. These are generally available in packs with several wood tones from which a close match can be selected to the color of the scratche...
Page 46: Lx Collection
42 lx collection 5. As the water level drops below the seats, use whatever means necessary to get the water out of the recessed seating areas and into the foot well, such as a wet/dry vacuum. 6. When the water level ceases to drop, use whatever means available to remove any remaining water from the ...
Page 47: Lx Collection
43 lx collection 13.0 water quality maintenance to decrease the risk of contracting a waterborne illness (e.G. An infection, bacteria or virus) and/or respiratory ailments, maintain water quality within specified limits. This will enhance your enjoyment and prolong the life of the hot tub’s equipmen...
Page 48: Lx Collection
44 lx collection warning: risk of personal injury, drowning or entrapment! Never leave your hot tub unattended for any reason while the cover is open and accessible, especially to small children and animals! Caution: risk of personal injury or spa damage! Never add chlorine tablets (trichlor) or aci...
Page 49: Lx Collection
45 lx collection 13.4 clearray® bulb replacement and quartz tube maintenance important: it is mandatory that the uv bulb is replaced and the quartz tube be cleaned every 12 months to maintain optimum performance. ! Danger: turn the spa breaker to the off position! ! Warning: drain the spa if your ar...
Page 50: Lx Collection
46 lx collection 3. Remove the black bulb boot (8) by sliding it over the cable away from the quartz seal compression nut (7), figure 3. 4. Slowly remove the uv bulb (4) out of the quartz tube. 5. Remove bulb socket (5) from the uv bulb (4), figure 4. 6. Remove the quartz seal compression nut (7) by...
Page 51: Lx Collection
47 lx collection 14. System test 1: assure there is no water dripping from the seal compression nut (7). If water is visible, stop and tighten the compression nut (7) using a pair of channel lock pliers to a maximum of 1/4 turn. If that does not fix the leak, then repeat quartz tube maintenance proc...
Page 52: Lx Collection
48 lx collection 14.0 error conditions/error messages your spa has a self-diagnostic control system. The system will automatically display the following if a problem is detected. Always insist on genuine jacuzzi replacement parts. 14.1 summer logic when the actual spa water temperature reaches 2°f (...
Page 53: Lx Collection
49 lx collection 14.6 panel flashes fl1 or fl2 a flashing “fl1” display means the flow switch is malfunctioning open, the filter cartridge is excessively dirty or an “air lock” condition has occurred at the circulation pump intake. A flashing “fl2” display means the flow switch is malfunctioning clo...
Page 54: Lx Collection
50 lx collection 14.9 panel displays blb uv bulb needs to be replaced. The message will flash between “blb” and the water temperature. The countdown timer for the uv bulb needs to be reset (section 11.6, page 34). A new uv bulb can be purchased from a local jacuzzi dealer. 15.0 troubleshooting proce...
Page 55: Lx Collection
51 lx collection 15.4 water is too hot reduce thermostat setting. 15.5 no heat 1. Check thermostat setting. 2. Keep the spa cover in place while heating. 3. Check the settings to see if your spa is in economy filtration/heating mode (page 30). Should checking the above steps fail to correct the prob...
Page 56: Lx Collection
52 lx collection 16.0 circuit board diagrams 16.1 north american dedicated power models (60 hz) this wiring diagram is used for all north american, 240v (60 hz) dedicated power models. Or mini-din cable provides constant 12 v ac from yellow transformer wires mini-din control panel cable light dcu 1 ...
Page 57: Lx Collection
53 lx collection 16.2 export models (50 hz) this wiring diagram is used for all export 230 vac 50 hz spa models. Light dcu 1 2 3 4 5 6 7 8 9 10 power exp bar exp bar brn blu c circ. Pump stereo power supply clear r ay grn tb1 blu blu j6 brn j5 brn blu blk blu brn blu brn blu blu brn brn brn 2 1 flow...
Page 58: Lx Collection
54 lx collection 17.0 optional bluewave™ spa stereo system to start enjoying your new stereo receiver, please read the following operation instructions in their entirety. 1. Media locker handle slide the handle to lock and unlock the protective door. 2. Power button press power button once to turn “...
Page 59: Lx Collection
55 lx collection warning: risk of electrical shock hazard exists and equipment damage! Never install or remove electrical devices (e.G. Apple device/mp3/usb/blue- tooth) while hands are wet or while sitting partially or fully immersed in spa! Caution: never leave electrical devices in the media lock...
Page 60: Lx Collection
56 lx collection 2. Treble setting: press the audio button 2 times to access the treble setting. The lcd display will change to “tre 0,” figure e. Press the up button to adjust the setting to a maximum of +5. Press the down button to adjust the setting down to -5. Note: the default setting is “0.” t...
Page 61: Lx Collection
57 lx collection 17.3 wireless remote control functions a wireless radio frequency (rf) remote control is supplied on all spas with the optional audio system. This remote provides control of the radio and over some media device functions. A. External media device playback the supplied remote control...
Page 62: Lx Collection
58 lx collection 17.4 electronic device connections and functions important: • if stereo unit is “on” (blue light is illuminated on the stereo power button) then press the power button on the remote once. • if stereo unit is in “standby” (red light is illuminated on the stereo power button) then pre...
Page 63: Lx Collection
59 lx collection c. Operating usb/mp3/apple device 1. Turn power “on” to the stereo unit. Turn power “on” to the remote. 2. The lcd screen on the remote will display the following: “welcome,” “usb,” “load,” “apple” (final display will vary depending on the device connected). All functions are perfor...
Page 64: Lx Collection
60 lx collection f. Connecting your bluetooth device: 1. Turn power “on” to the stereo unit. 2. From your bluetooth device, make sure the bluetooth setting is “on.” 3. Follow the pairing instructions for your bluetooth device and connect to the “bluewave” device that appears on your screen. 4. If as...
Page 65: Lx Collection
61 lx collection 4. Replace battery using cr2430 or equivalent (figure d). 5. Reinstall the battery cover, using the coin rotate the door to the close position (figure e). Note: remote unit is water resistant not waterproof. Although it is designed to be used while in the spa, it should never be lef...
Page 66: Lx Collection
62 lx collection.