1. DL manuals
  2. Jacuzzi
  3. Kitchen & Bath Fixtures
  4. J-SHOWER TOWER ENCLOSURE-Siena
  5. Installation And Operating Manual

Jacuzzi J-SHOWER TOWER ENCLOSURE-Siena Installation And Operating Manual

Manual is about: Jacuzzi J-SHOWER TOWERTM OPERATING MANUAL

Summary of J-SHOWER TOWER ENCLOSURE-Siena

  • Page 1

    Whirlpool bath r installation and operating manual j-shower tower ™ enclosure-siena ™ , merano ™.

  • Page 3

    1 important the bathtub must be installed per installation instructions d884000 for the merano™ or e160000 for the siena™. Follow the instructions to ensure that proper framing has been provided to support the j-shower tower. Finishing materials must be waterproof and sealed so that spray and conden...

  • Page 4

    2 bails see p age 7 w allbar see p age 9 f extrusion see p age 20 l extrusion see p age 20 t o p ring see p age 17 w all bracket see p ages 17 &18 t ower see p age 12 handle see p age 21 hand held shower, flex hose see p age 22 w a ter inlet see page 8 fixed p anel see p age 13 & 14 end extrusion se...

  • Page 5

    3 exploded view of j-shower tower end cap see p age 20 bott om rail see p age 15 & 16 set screw see p age 16 pins see p a ge 1 1 f a c epl a t e see p age 21 mixer/diverter (including hose connections) see p ages 10 & 1 1 fill spout see p age 8.

  • Page 6: Shower Tower Hardware

    4 shower tower hardware identification chart the diagrams for these fasteners are shown actual size for fast identification. Hardware screw cover cover qty.-6 h10 set screw #8-32 x 1 1/2" screw qty.-1 h17 lower track end cap cap qty. -1 h16 external tooth lock-washer #8 stainless steel washer qty.-4...

  • Page 7: Shower Tower Hardware

    5 shower tower hardware identification chart the diagrams for these fasteners are shown actual size for fast identification. Water inlet hardware nut qty.-1 w2 locknut 1/2"-14npt fibre washer 1.24 dia washer qty.-1 w1 wall bar hardware flathead screw #10-24 x 2 1/2" stainless steel screw qty.-2 wash...

  • Page 8: Shower Tower Hardware

    6 shower tower hardware identification chart plumbing hardware the diagrams for these fasteners are shown actual size for fast identification. Fiber washer .75 o.D. Washer qty.-2 screw qty.-6 phillips head screw m4x12 stainless steel p3 washer qty.-3 external tooth lock washer m4 washer qty.-6 nippl...

  • Page 9

    7 tower assembly 1. Assemble the four (4) bails to the tower wall. Do not overtighten the nuts on the threaded shaft end. Overtightening may break the stud. Illustration 1 bail set screw (8) bolt (8) h1 shelf nut (8) h2 h3 washer (8) h1 bolt qty.-8 slot fastener 10 x32 h2 nut qty.-8 hex nut 10 x 32 ...

  • Page 10

    8 2. Attach the water inlet and fill spout to the tower wall. (see illustration 2 and 2a.) illustration 2a fill spout nut qty.-1 w2 locknut 1/2"-14npt fiber washer 1.24 dia washer qty.-1 w1 water inlet illustration 2 nipple qty.-1 p5 nut caulk washer water inlet tower wall w2 w1 p6 caulk p7 fill spo...

  • Page 11

    9 3. Attach the wallbar assembly to the tower wall. (see illustration 3.) illustration 3 flathead screw #10-24 x 2 1/2" stainless steel external tooth washer 1/8" bead of caulk wallbar stand-off wb4 cap side view of wallbar wallbar shower head bracket soapdish shower wall kep nut flat washer screw w...

  • Page 12

    Illustration 5 attaching diverter valve to shower wall screw qty.-3 phillips head screw m4x12 stainless steel external tooth lock washer m4 p3 washer qty.-3 illustration 4 water lines to mixer/diverter valve screws m/f 90 ° elbow m/f 90 ° elbow washer p1 water supply to shower (12") cold water line ...

  • Page 13

    11 6. Attach the shower line to the water inlet and the fill spout line to the fill spout. (see illustration 6.) 7. Attach the three (3) pins to the bottom of the tower. (see illustrations 7 and 8.) 8. After these steps are completed, set the tower aside. P1 washer qty.-2 fiber washer illustration 6...

  • Page 14

    12 illustration 9 (left hand shown) 1. Locate the drilling template. Place it over the bathtub. The inner orange circle must be centered over the circular opening of the bathtub. (see illustration 9.) be sure the orange circle is spaced an equal distance around the bath cavity. The line marked back ...

  • Page 15

    13 illustration 10 3. Attach hot and cold water supply lines of the mixer/diverter to the stub-out supply lines. (see illustration 10.) 4. Locate the on/off handle and temporarily place it on the mixer valve. (see illustration 26.) with the mixer/ diverter valve in the off position, turn on the wate...

  • Page 16

    14 placing tower illustration 11 5. Dry fit tower pins into holes to check hole location. Apply sealant around the three tower wall holes on the bath and around the perimeter where the tower will set. (see illustration 11.) 6. Place the tower pins in the holes and push the tower down firmly. The tow...

  • Page 17

    7. Locate the bottom rail and the fixed panel. Lay a bead of sealant on the bottom of the fixed panel. Secure the bottom rail to the fixed panel. (see illustration 12.) drill a 3/32" diameter hole into the bottom rail at about 15 ° . Drill only through the first aluminum thickness. (see illustration...

  • Page 18

    16 fixed panel assemble to bath 8. Screw 1-1/2" allen set screw 3/4" deep into the bottom of the fixed panel. Lay a 1/4" bead of sealant under the bottom rail and inside the vertical frame. Place the assembly against the vertical edge of the tower and onto the bath surface. (see illustration 15.) se...

  • Page 19

    17 9. Locate the top ring. Remove the plastic retainer extrusion and set it aside. Place the top ring on the fixed panel and tower wall. The top ring groove on the underside of the top ring must mate with the top of the fixed panel. The flat portion of the ring should be parallel with the back wall....

  • Page 20

    18 11. Drill a 3/32" diameter hole into the top ring at about 15 ° . (see illustration 20.) engage the top of the fixed panel with the top ring groove. Secure the top of the fixed panel to the top ring. (see illustration 21.) 12. Plumb and square the tower. Mark a point through each slot of the wall...

  • Page 21

    19 fixed glass frame attachment 13. Apply sealant in frame and extrusion. Align and place extrusion above end cap onto the fixed glass. Illustration 23 sealant fixed glass end extrusion.

  • Page 22

    20 14. Install on the sides of the tower the aluminum extrusions provided. They may be sealed in place or secured with screws. Seal the end cap and place into the end of the lower track. Secure with self taping screw. (see illustration 24.) caulk back wall wall end cap f-extrusion caulk wall l-extru...

  • Page 23

    15. Assemble the face plate as shown in illustration 25. Assemble the handle as shown in illustration 26 (see handle instructions in handle kit). Illustration 25 attaching face plate handle installation screw faceplate tower wall large foam gasket small foam gasket illustration 26 apply sealant all ...

  • Page 24

    2i. Attach the shower hose. (see illustration 27.) use the washer supplied with the shower hose. 22. For hot and cold operation of the handle, see illustration 28. Hot cold handle operation illustration 28 off hand held shower washer tower wall flex hose washer teflon tape water connector wall bar i...

  • Page 28

    Printed in the u.S.A. Product specifications are subject to change without notice. Use installation instructions supplied with product. Jacuzzi whirlpool bath has obtained applicable code (standards) listings generally available on a national basis for products of this type. It is the responsibility...