Salon™ spa air bath and whirlpool installation and operating instructions ©2006 jacuzzi whirlpool bath el21000b 10/06 installer: leave this manual for homeowner. Homeowner: read this manual and keep for future reference. Owner's record save these instructions for future use. Complete and mail-in the...
English important safety instructions read and follow all instructions save these instructions instructions pertaining to a risk of fire, electric shock, or injury to persons warning — when using this unit, basic precautions should always be followed, including the following: danger: — to reduce the...
English product specifications are subject to change without notice. Use installation instructions supplied with product. The company has obtained applicable code (standards) listings generally available on a national basis for products of this type. It is the responsibility of the installer/owner t...
English contents safety instruction ______________________________________________________________________ 2-3 contents _____________________________________________________________________________ 4 specifi cations _________________________________________________________________________ 5-8 roughi...
English specifications important: read complete instructions before beginning installation. Each bath arrives ready for installation, completely equipped with blower motor, pump/motor assembly, heater, and plumbing necessary for operation. Remove the bath from the carton. Retain the shipping carton ...
English specifications (rectangular) rh = right hand note: the overall dimensions are nominal with a tolerance of +0 and -1/4" (6,4 mm). For mito™ unit: electrical service requirements : it requires a dedicated gfci protected separate circuit. Blower and motor/pump: 120 vac, 20 amp, 60 hz. Dedicated...
English 7 jacuzzi whirlpool bath el21000b 10/06 specifications (oval and round) rh = right hand note: the overall dimensions are nominal with a tolerance of +0 and -1/4" (6,4 mm). For all units: electrical service requirements : all require a dedicated gfci protected separate circuit. Blower: 120 va...
English 8 jacuzzi whirlpool bath el21000b 10/06 specifications (corner) rh = right hand note: the overall dimensions are nominal with a tolerance of +0 and -1/4" (6,4 mm). For all units: electrical service requirements : all require a dedicated gfci protected separate circuit. Blower: 120 vac, 20 am...
English 9 jacuzzi whirlpool bath el21000b 10/06 roughing-in reference note: 1. The overall dimensions are nominal with a tolerance of +0 and -1/4" (6,4 mm). 2. Measurements inside each unit represent cutout in fl oor to allow for drain/overfl ow. 3. All measurements are in inches. To convert to mill...
English 10 jacuzzi whirlpool bath el21000b 10/06 roughing-in reference note: 1. The overall dimensions are nominal with a tolerance of +0 and -1/4" (6,4 mm). 2. Measurements inside each unit represent cutout in fl oor to allow for drain/overfl ow. 3. All measurements are in inches. To convert to mil...
English 11 jacuzzi whirlpool bath el21000b 10/06 roughing-in reference note: 1. The overall dimensions are nominal with a tolerance of +0 and -1/4" (6,4 mm). 2. Measurements inside each unit represent cutout in fl oor to allow for drain/overfl ow. 3. All measurements are in inches. To convert to mil...
English 12 jacuzzi whirlpool bath el21000b 10/06 roughing-in reference note: 1. The overall dimensions are nominal with a tolerance of +0 and -1/4" (6,4 mm). 2. Measurements inside each unit represent cutout in fl oor to allow for drain/overfl ow. 3. All measurements are in inches. To convert to mil...
English 13 jacuzzi whirlpool bath el21000b 10/06 framing and support the drain/overfl ow of the bath extends below the bottom of the bath. Note that this requires a cutout in the fl oor. The fl oor structure beneath the bath must be able to support a total weight of bath, water, and bather. Refer to...
English 14 jacuzzi whirlpool bath el21000b 10/06 electrical connection - blower duplex recept. * 3 prong plug *(not provided) floor 4" min. Or in accordance with local & building or electrical codes two (2) separate ground fault circuit interrupter (gfci) are required for the salon™ spa units (excep...
English 15 jacuzzi whirlpool bath el21000b 10/06 installation fuzion™ control panel installation note: the fuzion™ control panel is delivered loose and must be installed during the tub install. For fuzion™ drop-in and undermount installations, install the control panel as shown below. The control pa...
English 16 jacuzzi whirlpool bath el21000b 10/06 drain information a drain/overfl ow assembly (sold separately) must be installed on the bath, water tested, and connected to the sanitary system of the house. After opening the carton, inspect for damage and verify that the kit is of the proper fi nis...
English 17 jacuzzi whirlpool bath el21000b 10/06 typical bath fittings operation note: these instructions pertain to all bath products manufactured by jacuzzi whirlpool bath. Not all features dis- cussed in this instruction pamphlet apply to all baths. All baths manufactured by jacuzzi whirlpool bat...
English 18 jacuzzi whirlpool bath el21000b 10/06 electronic control panel operation (with standard chromatherapy lighting) all tubs in this product line (except the mito™ 6) come with electronic controls and standard chromatherapy lighting. Read and follow the operation instructions for the control ...
English 19 jacuzzi whirlpool bath el21000b 10/06 normal operation (with the bath fi lled to the proper level) bath light right air valve left air valve left air valve status leds right air valve status leds pump/motor status leds on/off pump/motor wave function toggle switches air bath blower status...
English control panel operation, mito™ 6 air bath controls general functions normal mode: press this button to turn the blower on. The blower will be on for 20 minutes. The intensity may be changed by using either the up arrow button or the down arrow button. Pressing this button a second time will ...
English 21 jacuzzi whirlpool bath el21000b 10/06 controlling whirlpool action after the electronic controls are set, the whirlpool action in your bath can be infl uenced by up to three additional factors – direction of fl ow, force of water, and (whirlpool jet) force of air. All baths manufactured b...
English 22 jacuzzi whirlpool bath el21000b 10/06 cleaning the bath to clean your bath, simply use a mild, nonabrasive liquid detergent solution. You can protect and restore the gloss to a dulled acrylic surface by applying meguiar's #10 mirror glaze, a product specifi cally designed for use on acryl...
English 23 jacuzzi whirlpool bath el21000b 10/06 lamp all units come standard with an underwater led light fi xture. There are no internal replacement parts for the led light fi xture. Replacement fi xtures are available from your jacuzzi whirlpool bath dealer. Repairs to the surface minor scratches...
English 24 jacuzzi whirlpool bath el21000b 10/06 general whirlpool bath troubleshooting guide probable causes problem remedy pump/motor does not start. Pump/motor operates but no fully adjustable jets are functioning. Pump/motor operates but air is not injected into water. Water leakage from pump un...
English 25 jacuzzi whirlpool bath el21000b 10/06 authorized service if you need a referral for a service company near you, or need assistance with operation or maintenance related questions, please call our service support department at 1-800-288-4002. Visit our web site at http://www.Jacuzzi. Com/ ...
English 26 jacuzzi whirlpool bath el21000b 10/06 jacuzzi whirlpool bath 14801 quorum dr., suite 400, dallas, tx 75254 service support: 1-800-288-4002 product specifications are subject to change without notice. Use installation instructions supplied with product. Jacuzzi whirlpool bath has obtained ...
Warranty coverage jacuzzi whirlpool bath (the “company”) offers the following express limited warranty to the original purchaser of any jacuzzi whirlpool bath designer collection bath product (“unit”) who purchases the product for personal or single family use (“user”). The company will repair or re...
Responsibilities of others inspecting the unit prior to installation is the responsibility of the installer or building contractor who acts on behalf of the user. They are responsible for ensuring the unit is free of defect or damage. Notices are placed on and in the unit and on the shipping carton ...