1. DL manuals
  2. Jacuzzi
  3. Kitchen & Bath Fixtures
  4. SEDONA
  5. Installation & Operating Instructions Manual

Jacuzzi SEDONA Installation & Operating Instructions Manual

Manual is about: Steam & Shower Base

Summary of SEDONA

  • Page 1

    Sedona ™ steam & shower base installation/operating instructions.

  • Page 2

    Important safety information read all installation instructions jacuzzi whirlpool bath does not recommend prolonged periods of use of the steamer. Prolonged use of the steam system can raise excessively the internal human body temperature and impair the body’s ability to regulate its internal temper...

  • Page 3: Contents

    Contents specifications _________________________________________________________________________ 2 roughing-in reference _________________________________________________________________ 2 framing and support ___________________________________________________________________ 3 steam enclosure ____...

  • Page 4

    *steampro supplied with nema 6-50p plug. Nema 6-50r receptacle required. Product specifications are subject to change without notice. Specifications dimensions 60" (1524 mm) l 32" ( 813 mm) w 18-5/8" ( 473 mm) h total weight/ floor loading 310 lbs (141 kg) /23 lb/sq. Ft. (112 kg/sq. M) product weigh...

  • Page 5

    10-1/2" x 5" drain cut-out 15-3/8" 33-1/4" 60-1/4" front of double studs sub-floor 90º 90º minimum 6" from finished ceiling or bottom of optional dome to temperature sensor location from steam generator maximum 7' from floor to digital controller location framing and rough-in details (for left hand ...

  • Page 6

    4 drain down locations there are several locations (left hand unit shown) where the optional automatic valve may be located when connecting to a drain line as shown in illustration. Right hand unit is mirror image. Exact location to be determined by installer. The manual drain valve can be moved fro...

  • Page 7

    5 minerals in the water or poor water quality can shorten the life of the steam generator or cause erratic operation if the tank is not drained regularly. Drain the tank frequently. Jacuzzi whirlpool bath also strongly recommends purchasing and installing the optional automatic drain down valve. The...

  • Page 8

    6 shut off valve water supply (3/8" copper tubing) water supply consult local authorities for plumbing code require- ments in your area. Connect house cold water supply to steam generator supply tubing. Important: jacuzzi whirlpool bath does not warrant connections of water supply fittings and pipin...

  • Page 9

    7 controller mounting finished wall mounting the low voltage control can be mounted directly to a finished wall either inside or outside the steam room. Using a 2" hole saw, drill a hole in the finished wall where the control is to be mounted (the control cable should already be roughed-in to this l...

  • Page 10

    8 wall probe must point downward 7/8" hole optional trim ring silicone sealant pigtail flange mounting after base is in position secure flange to studs with screws provided. If there is a gap between flange and stud shims must be used. Temperature sensor mounting the temperature sensor should be mou...

  • Page 11

    9 service access service access is through the removable panel. To remove panel, grab the middle of the panel and bow outwards till clips disengage. Service access panel grab panel in middle and bow outwards bow access panel outward from center shell access panel to reinstall the panel hold at an an...

  • Page 12

    10 remove screws mounting bracket shipping restraint water supply shut off valve to steam head drain down maintenance of the steampro unit maintenance of the steampro includes flushing and visually inspecting for water leaks. To remove the unit remove the access panel. Turn off power to the unit and...

  • Page 13

    11 troubleshooting there are no user serviceable parts in the generator. All repair should be performed by a qualified service person. For additional assistance or the factory authorized service person nearest you call the service department at 1-800- 363-0251 (this number is only for service for th...

  • Page 14

    12 troubleshooting.

  • Page 15

    13 wiring diagram.

  • Page 16

    14 ©2002 jacuzzi whirlpool bath t87100b 2/04 jacuzzi whirlpool bath national headquarters p.O. Drawer j, walnut creek, ca 94596 (925) 938-7070 service support: call (800) 288-4002 jacuzzi whirlpool shower base has obtained applicable code (standards) listings generally available on a national basis ...

  • Page 17: Steam Generator  Products

    Jacuzzi whirlpool bath c/o amerec p.O. Box 2258 woodinville wa, 98072 jacuzzi whirlpool bath, warrants that its steam generators (warranted products) are free of manufacturing defects both as to workmanship and material for 5 years and it will replace or repair defective parts or equipment for the p...

  • Page 18

    6. Procedure. Requests for repair or replacement, a return authorization number, or warranty information should be directed to amerec by calling toll-free 1-800-363-0251 or by writing to amerec, 17683 128th place n.E., woodinville, wa 98072. Defective product or parts returned for repair or replacem...

  • Page 19: Builder Group Bath Product

    Jacuzzi whirlpool bath limited warranty builder group bath product jacuzzi whirlpool bath p.O. Drawer j walnut creek, ca 94596-9885 warranty coverage jacuzzi whirlpool bath (the “company”) offers the following express limited warranty to the original purchaser of any jacuzzi whirlpool bath builder g...

  • Page 20

    Responsibilities of others inspecting the unit prior to installation is the responsibility of the installer or building contractor who acts on behalf of the user. They are responsible for ensuring the unit is free of defect or damage. Notices are placed on and in the unit and on the shipping carton ...