- DL manuals
- Jacuzzi
- Iron
- SteamPro
- Installation And Operating Manual
Jacuzzi SteamPro Installation And Operating Manual
Summary of SteamPro
Page 1
Steam generator installation and operating manual steampro tm steampr o.
Page 2: Important Safety Information
Important safety information read all installation instructions jacuzzi whirlpool bath does not recommend prolonged periods of use of the steamer. Prolonged use of the steam system can raise excessively the internal human body temperature and impair the body’s ability to regulate its internal temper...
Page 3: Contents
Contents installation of steam generator specifications ______________________________________________________________________________ 1 how to select generator size and electrical requirements ___________________________________________ 2 locating the steam generator _______________________________...
Page 4: Installation
How to select generator size step 1. Determine cubic footage of steam enclosure: multiply length inches x width inches x height inches to find cubic inches. Divide cubic inches by 1728 to determine cubic feet. Step 2. Find steam enclosure size within the ranges shown on the chart for the supply volt...
Page 5: Installation
Locating the steam generator the steam generator must be installed upright and level. The steam generator must be located within a 25 foot maximum steam line run to the steam head and within the 25 foot control wire length to any controls. It may stand attached to a horizontal base or to a wall. For...
Page 6: Installation
Plumbing instructions and cautionary notes on installation minerals in the water or poor water quality can shorten the life of the steam generator or cause erratic operation if the tank is not drained regularly. Drain the tank frequently. Jacuzzi whirlpool bath also strongly recommends purchasing an...
Page 7: Installation
Installation steam unit to be level and upright see page 5 for suggested locations water supply with shut-off valve (3/8 or 1/2 inch copper) to steam head see pages 8 and 9 for steam head plumbing and installation for vari- ous wall surfaces. Steam pipe 1/2 inch (minimum size) copper. 25 foot total ...
Page 8: Installation
Installation steam head installation for various wall surfaces jacuzzi whirlpool bath recommends that the steam shield be used for all steam head installations. The steam shield must be installed if the steam head is located on acrylic (or other plastic) wall surfaces or above a bath rim. The steam ...
Page 9: Installation
Installation 10 kw steam generator with two steam heads two steam heads may be installed with the model e210000 steam generator, if desired. This will reduce the sound level of the exiting steam and will provide more even steam distribution and less heat concentration in larger steam enclosures. Pos...
Page 10: Installation
1. Apply thread compound sparingly to male threads on fitting a. (keep thread compound from entering the valve.) 2. Using a backup wrench to hold fitting a, thread valve assembly onto fitting and tighten. Valve outlet must point as shown. 3. Make certain power is disconnected. Remove top cover. 4. R...
Page 11: Installation
Installation steam controls—available installation methods various control packages are available for use with the steam generator. The following instructions (a–c, pages 12 - 16) describe the different installations. Select one of the following control options: a. On/off 30 minute control. B. 30 mi...
Page 12: Installation
Installation apply sealant (100% silicone caulk) 1-3/4" diameter hole in finished wall (optional nut installation if back of wall is accessable) a. Steam control by 30 minute low voltage on/off control. This low voltage control can be located inside or outside the steam enclosure 1. Control cable ro...
Page 13: Installation
Installation general instructions for temperature control models 1. Control cable rough-in the low voltage control can be mounted up to 25 feet from the generator either inside or outside the steam room, also see #6 optional secondary digital generator control. String the 25' cable from the control ...
Page 14: Installation
Installation 5. Install generator control the low voltage control can be mounted directly to a finished wall either inside or outside the steam room. Using a 2" hole saw, drill a hole in the finished wall where the control is to be mounted (the control cable should already be roughed-in to this loca...
Page 15: Operation
Operation b. 30 minute temperature control the 30 minute temperature control features a 30 minute press on timer lighting up the word "steam" and a thermostatic control preset to reach 120 degrees fahrenheit. The digital control can be mounted either inside or outside the steam room. The preset temp...
Page 16: Operation
Operation c. Digital time and temperature control the digital control features an adjustable 60 minute time and temperature control with digital display. The actual room temperature and time remaining are alternately displayed every 5 seconds. The primary control can be mounted either inside or outs...
Page 17: Service
Service description of steampro steam generator the steampro series generator is the latest in modern steam generator design. The steampro steam generator uses a printed circuit assembly to monitor and control all the equipment needed to produce steam. The system has three functions: a timer that co...
Page 18: Troubleshooting
Troubleshooting there are no user serviceable parts in the generator. All repair should be performed by a qualified service person. For additional assistance or the factory authorized service person nearest you call the service department at 1-800- 363-0251. The trouble shooting guide below is meant...
Page 19: Troubleshooting
Troubleshooting s m o t p m y s s e s u a c e l b a b o r p n e k a t e b o t n o i t c a . " n o " l o r t n o c ) n o t h g il l o r t n o c ( . M a e t s t ' n o w t i n u t il m a e t s : e t o n r o y l i d a e t s y l r e p o r p p m e t / e m i t l a t i g i d n o d e y a l p s i d y a l p s ...
Page 20: Wiring Diagram
Wiring diagram product specifications are subject to change without notice. Use installation instructions supplied with product. Jacuzzi whirlpool bath has obtained applicable code (standards) listings generally available on a national basis for products of this type. It is the responsibility of the...
Page 21
Jacuzzi whirlpool bath, warrants that its steam generators (warranted products) are free of manufacturing defects both as to workmanship and material for 5 years and it will replace or repair defective parts or equipment for the period of time and in accordance with the conditions set forth below. T...
Page 22
6. Procedure. Requests for repair or replacement, a return authorization number, or warranty information should be directed to amerec by calling toll-free 1-800-363-0251 or by writing to amerec, 17683 128th place n.E., woodinville, wa 98072. Defective product or parts returned for repair or replacem...