Summary of The Cirrus IG
Page 1
The cirrus ig owner's manual tm.
Page 2: Important Safety Information
Save these instructions for future use. Owner's record important safety information read and follow all installation instructions jacuzzi whirlpool bath does not recommend spa water temperatures in excess of 104°f. High water temperatures in excess of 104°f and/or prolonged periods of use can raise ...
Page 3: Owner'S Manual
Contents owner's manual model d500000 the cirrus ig ™ whirlpool spa 1 installation instructions inspection and shipping claim unpacking indoor installation, outdoor installation, below ground outdoor installation, below ground (cont). Outdoor istallation, ground level or above equipment pack site pr...
Page 4: The Cirrus
The cirrus ig whirlpool spa specifications options • air blower • gas heater • electric heater • rigid insulated spa cover • air switch/timer • spa pillows standard features • three directionally-adjustable jets • six high volume fully-adjustable jets • water rainbow fill spout recirculating spout •...
Page 5: Installation
Inspection and shipping claims check for shipping damage upon receipt of the spa. Jacuzzi whirlpool bath is not responsible for damage to the spa sustained during shipping. If damage is evident before unpacking, see instructions regarding shipping claims on the outside of the carton and immediately ...
Page 6: Installation
Installation indoor installation support if you install your spa indoors, be sure to provide proper support. The spa is very heavy when filled with water and in use. The floor or deck it is placed on must be capable of supporting a 4345 lbs. Load, which includes weight of the spa occupants, water an...
Page 7: Installation
5 installation outdoor installation-below ground the overall length of plumping between the spa and the equipment pack must be less than 20 ft. If you are installing your spa below ground level, the base of the equipment pack must not be more than 9" above the spa rim. Your spa should be installed s...
Page 8: Installation
6 installation * support method spa rim 2" shut-off valves* (locate below spa water level) equipment pack base (locate less than 9" above spa rim) 2" pvc piping 20 ft. Max plumbing line length between spa and equipment pack (including vertical and horizontal) alternate drain line wooden supports* dr...
Page 9: Installation
Installation outdoor installation — ground level or above you may install your spa and equipment pack so the spa is at ground level or above. The unique characteristic of the equipment pack, which allows your spa system to be located away from the spa itself, is that it is designed to allow flexibil...
Page 10: Installation
8 installation equipment pack site preparation locate the equipment pack on a level surface (at least 5 feet but not more than 20 feet from the spa) where there is sufficient access to the equipment. Make sure the site selected will allow drainage of water away from the equipment pack. We recommend ...
Page 11: Installation
Your equipment pack is an electrical device. It has been made to operate as safely as possible with many safeguards designed in. It complies with the nec (national electrical code). It must be installed at least 5 feet away from the spa and grounded properly in order to maintain these safeguards. (s...
Page 12: Installation
10 installation plumbing preliminary assembly once your equipment pack is installed, attach the suction equalizer tube assembly provided to the suction inlets of the pumps. Align pump flange ends of the assembly and install using gaskets, bolts and washers provided. Next, install the 1 1/2" x 3/4" r...
Page 13: Installation
Installation plumbing layout heater plumbing use at least 4 ft. Of copper pipe in the inlet and outlet plumbing of a gas heater (refer to local codes). Install a current collector in each water line to the heater if an electric heater is used. Piping should be 1 1/2" or larger. You must install a sw...
Page 14: Optional Air Blower
12 optional air blower two channels under the seating area of your cirrus ig receive air from the air blower and distribute the air throughholes in the seating area (to be drilled according to instructions on the following page). As the pressurized air is released from the holes, tiny bubbles are fo...
Page 15: Installation
13 seat air hole drilling (when optional air blower is installed) seat air holes because the air blower is an optional feature of the cirrus ig, air holes are not factory drilled in the seating area. Included with your spa are an air hole drill guide and a 5/32" diameter drill bit with which to dril...
Page 16: Installation
14 alternate use of water rainbow spout as fill spout you can use your water rainbow spout as a fill spout by permanently plumbing it to a fresh water supply if codes permit. Local plumbing codes may require the use of an anti-siphon valve for such a connection. Do not interconnect water supply with...
Page 17: Operation
15 equipment set-up important: your spa equipment pack must have two professionally installed 230 vac 15 amp electrical circuits from your house electrical panel. Additional power will be required for optional equipment, such as heater, air blower, or chlorinator. A proper ground wire run to a groun...
Page 18: Operation
16 shut-off valves and piping not provided by jacuzzi whirlpool bath priming procedure i use this priming procedure if your installation is such that the base of the equipment pack is level with or above the rim of the spa (see illustration.) 1. Turn all switches to off. Turn off circuit break- ers ...
Page 19: Operation
17 priming procedure ii use this priming procedure if your installation is such that the base of the equipment pack is lower than the rim of the spa (see illustration.) shut-off valves and piping not provided by jacuzzi whirlpool bath priming procedure ii (below water level) 1. Turn all switches to ...
Page 20: Spa Control
Water rainbow spout suction covers skimmer/ filters water level mark silent air control directionally adjustable jet fully adjustable whirlpool jet silent air controls 18 spa control your spa and equipment pack installation must include a control system such as an air switch and/or timer system whic...
Page 21: Operation
19 water rainbow ™ the water rainbow spout will add the soothing sound of a waterfall to your bathing pleasure, as well as provide a beautiful cascade of shimmering water for an exciting visual effect. Activate the waterfall feature by first turning on the whirlpool function, then rotate downward th...
Page 22: Maintenance
Water quality and water chemistry maintaining water quality and water chemistry in your spa is extremely important and should be a regular part of your spa maintenance program, as a neglected spa can be a breeding place for dangerous bacteria. The water quality of your spa is maintained by a combina...
Page 23: Water Chemistry
Water chemistry (continued) disinfecting: add a disinfectant to the water on a regular basis to help control the amount of bacteria, algae and organic materials. Such bacterial contaminants, if not controlled, could cause skin rashes or other physical problems. To disinfect the spa for normal use, f...
Page 24: Nance
Water level/drain the water level in the spa must be maintained at its normal level. Evaporation and splashing will cause the water level to drop. When concentrations of impurities from evaporation, water quality chemicals, body oils, perfumes, dirty feet, and winds, etc., accumulate in the spa and ...
Page 25: Maintenance
23 automatic filtration/maintenance the spa should be covered to keep out debris. The filter cycle should be run at least two hour per day to maintain water quality. If your equipment pack has a timer installed, the timer may turn on the filter automatically each day for you in your absence. Your ti...
Page 26: Maintenance
24 maintenance cleaning your spa your cirrus ig spa shell consists of two layers of plastic materials. Its smooth top surface of acrylic is tough and durable and contains concentrated color. This is supported by a substantial thickness of fiberglass-reinforced polyes- ter resin. A catalyst causes a ...
Page 27: Troubleshooting Guide
Problem remedy probable cause 25 a. Check circuit breaker. B. Reset thermostat. C. Adjust pressure switch. D. * e. Check circuit breaker. 1. Water will not heat. 2. Water not clean. A. Filters clogged (dirty). B. Skimmer basket clogged. C. Clogged or blocked suction strainer. D. Improper maintenance...
Page 28: Troubleshooting Guide
Remedy probable cause problem 7. Water leakage at pump shaft. (rotating connection between pump and motor). 8. Motor will not start. A. Worn or damaged pump seal. B. Foreign matter trapped in pump. A. Optional timer or switch set at off. B. Circuit breaker tripped or in off position. C. Locked shaft...
Page 29
Printed in the u.S.A. A printed on recycled paper product specifications are subject to change without notice. Use installation instructions supplied with product. Jacuzzi whirlpool bath has obtained applicable code (standards) listings generally available on a national basis for products of this ty...