1. DL manuals
  2. Jacuzzi
  3. Plumbing Product
  4. Verona
  5. Installation And Operating Manual

Jacuzzi Verona Installation And Operating Manual

Manual is about: J-CORNER SHOWER TOWER

Summary of Verona

  • Page 1

    Whirlpool bath r installation and operating manual j-corner shower tower ™ enclosure-verona ™.

  • Page 3

    1 important the bath must be installed according to installation instructions (f258000) for the verona™ whirlpool bath. Follow the instructions to ensure that proper framing has been provided to support the j-corner shower tower. Finishing materials must be waterproof and sealed so that spray and co...

  • Page 4

    2 fixed p anel see p age 13 & 14 bails see p age 6 f a c epl a t e see p age 19 w allbar see p age 7 mixer (including hose connections) see p ages 8 & 1 1 l extrusion see p age 18 l extrusion see p age 18 t o p ring see p age 15 & 16 w all bracket see p age 15 & 16 t ower see p age 10 handle see p a...

  • Page 5

    3 exploded view of j-corner shower t o wer end cap see p age 18 bott om rail see p age 13 & 14 set screw see p age 14.

  • Page 6: Shower Tower Hardware

    4 shower tower hardware identification chart the diagrams for these fasteners are shown actual size for fast identification. Hardware z low track end cap cap qty. -1 external tooth lock-washer #8 stainless steel washer qty.-1 y sheet metal screw #8-18x2" s.S. X screw qty.-1 screw, hex washer bolt 1/...

  • Page 7: Shower Tower Hardware

    5 shower tower hardware identification chart the diagrams for these fasteners are shown actual size for fast identification. Hardware nut qty.-1 j washer qty.-1 i water inlet hardware locknut 1/2"-14npt fibre washer 1.24 dia wall bar hardware flathead screw #10-24 x 2 1/2" stainless steel screw qty....

  • Page 8

    Tower assembly 1. Assemble the four (4) bails to the tower wall. (see illustration 1.) do not overtighten the nuts on the threaded shaft end. Overtighten- ing may break the stud. Bail illustration 1 bail set screw (8) bolt (8) shelf nut (8) c a b external tooth lock-washer #10 stainless steel washer...

  • Page 9

    7 3. Attach the wallbar assembly to the tower wall. (see illustration 3.) flathead screw #10-24 x 2 1/2" stainless steel h g illustration 3 1/8" bead of caulk wallbar stand-off external tooth washer f (2) screw e (2) cap side view of wallbar wallbar shower head bracket soapdish shower wall kep nut h...

  • Page 10

    Illustration 5 attaching mixer valve to shower wall screw qty.-3 n cross recess head screw m4x12 stainless steel external tooth lock-washer m4 stainless steel m washer qty.-3 illustration 4 water lines to mixer valve ✳ use thread sealant screws (3) washer (3) n m k washer qty.-1 fiber washer .75 o.D...

  • Page 11

    Illustration 8 o pin qty.-3 flat washer #8 type b stainless steel washer qty.-3 p pan head screw #8-32 x 1/2" stainless steel screw qty.-3 q screw q washer p pin o tower bottom illustration 7 tower pins pin #8-32 .25dia x 1" k washer qty.-1 illustration 6 12" hose water inlet tower wall fiber washer...

  • Page 12

    10 tower installation 1. To locate the drilling template, place it over the bath. The template should be against the bath flange edge and template corner 'a' should be at the bath's corner. (see illustration 9.) note: if bath has been installed with finish materials over bath flange, trim an amount ...

  • Page 13

    11 5. Attach hot and cold water supply lines of the mixer to the stub-out supply lines. (see illustration 10.) 6. Locate the on/off handle and temporarily place it on the mixer valve. (see illustration 26 on page 19.) with the mixer valve in the off position, turn on the water supply. Check for leak...

  • Page 14

    12 placing tower illustration 11 7. Dry fit tower pins into holes to check hole location. Apply sealant around the three tower wall holes on the bath and around the perimeter where the tower will sit. (see illustration 11.) 8. Place the tower pins in the holes and push the tower down firmly. The tow...

  • Page 15

    Fixed panel bottom rail lay a 1/4" bead of sealant under the fixed panel two screws 15 ° illustration 14 illustration 12 illustration 13 s r 15 ° 1/8" important: must drill at a 15 ° angle to avoid drilling through door guide area. Important: must drill at a 15 ° angle to avoid drilling through side...

  • Page 16

    14 fixed panel assemble to bath 11. Screw 1 1/2" allen set screw 3/4" deep into the bottom of the fixed panel. Lay a 1/4" bead of sealant under the bottom rail and inside the back channel of the vertical frame. Place the assembly against the vertical edge of the tower and onto the bath surface, inte...

  • Page 17

    Illustration 19 washer (1) screws (2) screw into fixed panel y w x screw(1) screw here external tooth lock-washer #8 stainless steel washer qty.-1 y bolt qty.-2 w sheet metal screw #8-18x 2" s.S. Screw qty.-1 x ring to tower screw, hex washer bolt 1/4-20x2.5" illustration 16 bracket locating paralle...

  • Page 18

    Illustration 20 important: must drill at a 15 ° angle to avoid drilling through roller track of top ring. Illustration 22a bolt qty.-2 w m3.5x9.5mm stainless steel screw qty.-1 s drilling top ring ring to bracket illustration 22b ring to bracket illustration 21 drilling top ring screw, hex washer bo...

  • Page 19

    17 16. Apply sealant in frame and extrusion. Align and place extrusion above end cap onto the fixed glass. Fixed glass frame end attachment illustration 23 sealant fixed glass end extrusion.

  • Page 20

    17. Install on the sides of the tower the aluminum extrusions provided. They may be sealed in place or secured with screws (s, quantity 6). Seal the end cap by applying clear silicone sealant prior to placing into the end of the lower track. Secure with self-tapping screw s. 18 end cap l-extrusion l...

  • Page 21

    Illustration 25 faceplate tower wall foam gasket sealant hand held shower washer tower wall flex hose washer teflon tape water connector wall bar illustration 27 illustration 26 handle installation hot cold illustration 28 plug foam gasket 3"o.D. (not shown see page 5) foam gasket off screw washer c...

  • Page 24

    Printed in the u.S.A. Product specifications are subject to change without notice. Use installation instructions supplied with product. Jacuzzi whirlpool bath has obtained applicable code (standards) listings generally available on a national basis for products of this type. It is the responsibility...