1. DL manuals
  2. JAI
  3. Digital Camera
  4. CB-030GE
  5. User manual

JAI CB-030GE User manual

Manual is about: Digital Monochrome / Color Progressive Scan GigE Vision Camera

Summary of CB-030GE

  • Page 1

    User's manual cm-030ge cb-030ge digital monochrome / color progressive scan gige vision camera document version: 1.0 camera revision: a.

  • Page 2

    Cm-030 ge / cb-030 ge table of contents 1. General............................................................................................ - 3 - 2. Camera nomenclature .......................................................................... - 3 - 3. Main features .................................

  • Page 3

    Cm-030 ge / cb-030 ge 8.5.1 continuous operation .......................................................................... - 29 - 8.5.2 pre-select trigger mode ....................................................................... - 30 - 8.5.3 pulse width trigger mode ................................

  • Page 4

    Cm-030 ge / cb-030 ge 1. General this manual covers the digital monochrome progressive scan camera cm-030ge and color progressive scan camera cb-030ge the cm-030ge/cb-030ge is a new addition to jai gige vision compliant camera series. Both the monochrome version cm-030ge and the color version cb-030...

  • Page 5

    Cm-030 ge / cb-030 ge 3. Main features • member of compact series, covering vga to uxga resolution • 656 (h) x 494 (v) 7.4 µm square pixels • 1/3” progressive scan – monochrome and bayer mosaic color versions • high frame rate of 90.5 frames/second with full resolution in continuous operation • 90 f...

  • Page 6

    Cm-030 ge / cb-030 ge 4. Locations and functions se ria ln o. Fcc s ea l ca uti on s ea l ① ② ③ ④ ⑤ ⑥ ⑦ ⑧ power / trig gige ⑨ 1 lens mount c-mount (note *1) 2 ccd sensor 1/3 inch ccd sensor 3 12-pin connector dc +12v power and gpio interface 4 rj-45 gigabit ethernet connector with threaded holes for...

  • Page 7

    Cm-030 ge / cb-030 ge 5. Pin assignment 5.1 12-pin multi-connector (dc-in/gpio/iris video) type: hr10a-10r-12pb (hirose) male. Pin no. Signal remarks 1 gnd 2 +12 v dc input (seen from rear of camera.) 3 opt in 2 (-) / gnd (*1) 3 4 5 6 7 8 9 10 11 12 1 2 4 opt in 2 (+)/iris video out (*1) 5 opt in 1 ...

  • Page 8

    Cm-030 ge / cb-030 ge 6. Gpio (inputs and outputs) 6.1 overview all input and output signals pass through the gpio (general purpose input and output) module. The gpio module consists of a look-up table (lut – cross-point switch), 4 pulse generators and a 12-bit counter. In the lut, the relationship ...

  • Page 9

    Cm-030 ge / cb-030 ge 6.1.2 12-bit counter a 25 mhz clock or the camera pixel clock (40 mhz) can be used as a source. The counter has a “divide by n”, where n has the range 1 through 4096, allowing a wide range of clock frequencies to be programmed. Setting value 0 is bypass, setting value 1 is 1/2 ...

  • Page 10

    Cm-030 ge / cb-030 ge 6.2.2 recommended external output circuit diagram for customer hirose-12 connector pin 8 and 10 hirose-12 connector pin 7 and 9 out 270 +5v to +24v user power 2 user side camera inside from camera circuit external output +12v to 220 fig.6. External output circuit , opt out 1 an...

  • Page 11

    Cm-030 ge / cb-030 ge 6.3 inputs and outputs table output port time stamp reset opt out1 opt out2 pulse gen. 0 pulse gen. 1 pulse gen. 2 pulse gen. 3 trigger 0 trigger 1 × × × × × ○ ○ ○ ○ lval in × × × × × ○ ○ ○ ○ dval in × × × × × ○ ○ ○ ○ fval in × × ○ ○ × ○ ○ ○ ○ een in ○ ○ ○ ○ ○ ○ ○ ○ ○ opt in 1 ...

  • Page 12

    Cm-030 ge / cb-030 ge 6.4.2 12-bit counter start point end point length start point end point length address internal name genicam name access size value (range) clocksource 0x00: 25mhz 0xb000 counter clock choice r/w 4 0x01: pixel clock clockprescaler 0x000: bypass 0x001: 1/2 dividing 0xb004 counte...

  • Page 14

    Cm-030 ge / cb-030 ge 6.5 gpio programming examples 6.5.1 gpio plus pwc shutter example: 10µs unit pulse width exposure control (pwc). Pixel clock is 40mhz. 400 clocks (500-100) equals 10µs. Address register value 0xa040 trigger mode 2 = pwc ( pulse width control) 0xb000 clock choice 1 = pixel clock...

  • Page 15

    Cm-030 ge / cb-030 ge 6.5.2 internal trigger generator create a trigger signal and trigger the camera address register value 0xa040 trigger mode 1 = eps 0xb000 clock choice 1 = pixel clock 0xb004 counter dividing value 863 = 1/864 dev(line rate) 0xb008 length counter 0 1000 clocks 0xb00c start point...

  • Page 16

    Cm-030 ge / cb-030 ge 7. Gige vision streaming protocol (gvsp) 7.1 digital video output (bit allocation) although the cm-030ge and cb-030ge are digital cameras, the image is generated by an analog component, the ccd sensor. The table and diagram below show the relationship between the analog ccd out...

  • Page 17

    Cm-030 ge / cb-030 ge 7.2.3 gvsp_pix_mono10_packed (10 bit) 2 3 4 5 6 7 8 9 0 1 x x 0 1 x x 2 3 4 5 6 7 8 9 2 3 4 5 6 7 8 9 0 1 x x 0 1 x x 2 3 4 5 6 7 8 9 y3 y1 y0 y2 address internal name access size value 0x01080001:mono8 0xa410 pixel format type r/w 4 0x01100003:mono10 0x010c0004:mono10 packed 7...

  • Page 18

    Cm-030 ge / cb-030 ge 7.3.4 gvsp_pix_baygb10 “bayergb10” odd line 1 byte 2 byte 3 byte 4 byte 0 1 2 3 4 5 6 7 8 9 x x x x x x 0 1 2 3 4 5 6 7 8 9 x x x x x x g0 g0 b1 b1 even line 0 1 2 3 4 5 6 7 8 9 x x x x x x r0 r0 0 1 2 3 4 5 6 7 8 9 x x x x x x g1 g1 address internal name access size value 0x01...

  • Page 19

    Cm-030 ge / cb-030 ge 8. Functions and operations 8.1 gige vision standard interface the cm-030ge and cb-030ge are designed in accordance with the gige vision standard. It transmits digital images over cat5e or cat6 ethernet cables. All camera functions are also controlled via the gige vision interf...

  • Page 20

    Cm-030 ge / cb-030 ge 8.2.2 video data rate (network bandwidth) the video bit rate for cm-030ge and cb-030ge is: model pixel type packet data volume (in case the packet size is 1500) in case using jumbo frame, the packet data will be improved by 2 %. For cm-030ge and cb-030ge, the jumbo frame can be...

  • Page 21

    Cm-030 ge / cb-030 ge note: the following is valid if you are using intel(r) 1000 . Accordingly the procedure is different if you use different nic appeared on network adaptors. In that case, set the item of a similar content described here. (8)click [ advanced ] tab. (9) select jumbo frames of prop...

  • Page 22

    Cm-030 ge / cb-030 ge (10)click [ ok ] . (11)close [ device manager ] . (12)close [ system properties ] clicking [ok] . 8.2.4 packet delay packet delay is one of gige vision functionalities. This function controls the data bandwidth through network. When the delay value increases, the reliability of...

  • Page 23

    Cm-030 ge / cb-030 ge the camera has 1/2, 1/4 or 1/8 partial scanning for faster frame rates. Vertical binning is also available. The camera can operate in continuous mode as well as in 4 triggered modes: - pre-select - pulse width - sequential trigger (with pre-selected exposure time) - delayed rea...

  • Page 24

    Cm-030 ge / cb-030 ge 8.3.3 electronic shutter cm-030ge / cb-030ge have conventional shutter functions as well as the genicam standard “exposure time abs” function. Preset shutter 10 steps preset shutter are available: off (1/90); 1/100, 1/120; 1/250; 1/500; 1/1,000; 1/2,000; 1/4,000; 1/8,000; 1/10,...

  • Page 25

    Cm-030 ge / cb-030 ge gpio in combination with pulse width trigger more precise exposure time can be obtained by using gpio in combination with pulse width trigger mode. The clock generator and counter can be programmed in very fine increments. As for the setting example, refer to chapter 6.5.1. 8.3...

  • Page 26

    Cm-030 ge / cb-030 ge 8.3.6 rear panel indicator. The rear panel mounted led provides the following information: power / trig gige amber: power connected - initiating steady green : camera is operating in continuous mode flashing green : the camera is receiving external trigger ethernet connector in...

  • Page 27

    Cm-030 ge / cb-030 ge 8.4.2 horizontal timing the lval period is shown for normal continuous mode. Full frame read out / patial read out 1lval 864ck = 21.6us 1ck= 25ns lval data out 659ck 31 ck 690ck 174ck dval 656ck 2ck 16ck ob valid data fig. 18. Horizontal timing 8.4.3 vertical timing the fval pe...

  • Page 28

    Cm-030 ge / cb-030 ge 8.4.4 partial scanning the fval period is shown for 1/2 partial scan in normal continuous mode. 1 line = 26.7 μ s vertical timing the below diagram and table provide vertical timing information for the fixed partial scan settings 1/2, 1/4, 1/3 and 2/3 lval fval dval data een va...

  • Page 29

    Cm-030 ge / cb-030 ge the horizontal timing is the same the full scanning. Full frame read out / patial read out 1lval 864ck = 21.6us 1ck= 25ns lval data out 659ck 31 ck 690ck 174ck dval 656ck 2ck 16ck ob valid data fig.21. Horizontal timing for partial scanning 8.4.5 vertical binning vertical binni...

  • Page 30

    Cm-030 ge / cb-030 ge v binning lval fval 1+2 3+4 491+ 492 493+ 494 davl 5l 4l 247l 1l ob data ob valid data ob 1l ccd exposure een frame rate 257l 166.2fps fig.23. Vertical timing for vertical binning 8.5 operation modes this camera can operate in 5 primary modes. 1. Continuous mode pre-selected ex...

  • Page 31

    Cm-030 ge / cb-030 ge 8.5.2 pre-select trigger mode an external trigger pulse initiates the capture, and the exposure time (accumulation time) is the fixed shutter speed set by registers. The accumulation can be lval synchronous or lval a-synchronous. The resulting video signal will start to be read...

  • Page 32

    Cm-030 ge / cb-030 ge lval_a-sync timing lavl async tri g 1l( mi n) ccdexposur e een exposur e t i me favl 3μ s± 1μ s when a trigger pulse is input during fval low period, lval a-sync mode functions. Note) in case pe is equal or more than 2 and equal or less than 4, it is lval a-sync mode function. ...

  • Page 33

    Cm-030 ge / cb-030 ge lval_sync timing lavl sync trig lval 1l( max) 1l ccd exposure een exposure time favl full: 6l ～ 7.1l(131us ～ 152.6us) v binning:4l ～ 5.2l(98.4us ～ 121.2us) 1l (min) in this period, the falling edge of trigger pulse is prohibited when a trigger pulse is input during fval high pe...

  • Page 34

    Cm-030 ge / cb-030 ge 8.5.4 sequential trigger mode (pre-select trigger) the roi, shutter and gain values can be preset up to 10 sequences. Along with every trigger input, the image data with the preset sequence is output as described below. Signals added to trigger can be selected by 0xb060 camera ...

  • Page 35

    Cm-030 ge / cb-030 ge the following table shows the minimum trigger interval in synchronous accumulation mode. In case of a-synchronous accumulation mode, the exposure time should be added to figures in this table. Full scan 2/3partial 1/2 partial 1/4 partial 1/8 partial 1/2 v binning 514 l 364 l 29...

  • Page 36

    Cm-030 ge / cb-030 ge 8.5.6 optical black transfer mode it is possible for the user to decide whether the optical black (ob) portion of the image will be transferred or not. The optical black part can be used for black reference in the application software. Setting register 0xa41c turns the optical ...

  • Page 37

    Cm-030 ge / cb-030 ge 8.6 operation mode and functions matrix id (value) note 1 mode shutter preset / program. Vertical binning note 2 partial scanning auto iris lval output sync/async continuous 0x00 yes yes yes --- yes ( note 3) edge pre- select 0x01 yes yes yes auto no (ps) pulse width not applic...

  • Page 38

    Cm-030 ge / cb-030 ge 9. Register map the below table provides detailed information for the hardware registers used for controlling the camera and obtaining information on the status of the camera. The content of this register map is also found in the xml file, as stipulated by the genicam standard....

  • Page 39

    Cm-030 ge / cb-030 ge number of messaging channels 0x0900 r 4 this camera has 1 number of available message channel number of stream channels 0x0904 r 4 this camera only has 1 number of available stream channel bit 31:multiple read this is a capability register indicating which one of the non-mandat...

  • Page 40

    Cm-030 ge / cb-030 ge standard camera functions registers: address function read / write value / range of default size description value value 0= preset shutter sets exposure time for image capture. 0xa000 shutter mode r/w 4 1= programmable exposure 0 4=exposure timeabs 0=off; 0xa004 preset shutter ...

  • Page 41

    Cm-030 ge / cb-030 ge address function read / write value / range of default size description value value 0xa300 save settings into user area w 4 1=user area1 allows use to save all camera settings. Last used area number becomes new default. 2=user area2 1 3=user area3 0=factory area allow the user ...

  • Page 42

    Cm-030 ge / cb-030 ge address function read / write value / range of default size description value value th 0xc08c sequence gain 6 r/w 4 -84 to 336 pre-program 6 gain value 0 th 0xc090 sequence gain 7 r/w 4 -84 to 336 pre-program 7 gain value 0 th 0xc094 sequence gain 8 r/w 4 -84 to 336 pre-program...

  • Page 43

    Cm-030 ge / cb-030 ge address function read / write value / range of default size description value value 4 sequence roi height max 8 to 494 0xc144 r/w size-y9 4 sequence roi height max 8 to 494 0xc148 r/w size-y10 sequence roi 4 0xc14c r/w 0 to 648 0 offset-x1 sequence roi 4 0 to 648 0 0xc150 r/w o...

  • Page 44

    Cm-030 ge / cb-030 ge gige vision streaming related registers: address function read / write value / range of default size description value value horizontal image size return proper value when normal, v-bin & partial 0xa400 r 4 return proper value when normal, v-bin & partial 0xa404 vertical image ...

  • Page 45

    Cm-030 ge / cb-030 ge 0xa64c soft trigger 3 r/w 4 0=low, 1=high 0 0xa714 fpga version r 4 - 44 -.

  • Page 47

    Cm-030 ge / cb-030 ge address function read / write value / range of default size description value value end point counter 2 0xb03c r/w 4 0x00001 to 0xfffff end point 1 0 free run 1 high level clear 0xb040 counter 2 clear r/w 4 2 low level clear 0 4 rising edge clear 8 falling edge clear 0xb044 len...

  • Page 48

    Cm-030 ge / cb-030 ge 10. External appearance and dimensions 44 29 c-mount 13 26 26 (1.73) (1.1 4) 14. 5 (0.57) (0.51) 5 (0.2) (1. 02 ) (1. 02 ) (depth0.16) 59 75 se ria ln o. 6-m3depth4 (depth0.16) fc c s ea l ca uti on s ea l 67 3-m3depth4 5 (0.2) (2.64) (2.95) (2.32) outside size tolerance ± 0. 3...

  • Page 49

    Cm-030 ge / cb-030 ge 11. Specifications 11.1 spectral response fig. 29. Spectral response for cm-030ge i r fi l t er fig.30. Spectral response for cb-030ge - 48 -.

  • Page 50

    Cm-030 ge / cb-030 ge 11.2 specification table specifications cm-030ge cb-030ge scanning system progressive scan frame rate full frame 90.5 frames/sec. Progressive (511 lines/frame) pixel clock 40 mhz line frequency 46.296 khz ( 1h = 21.6 µs ), (864 pixel clock/line) ccd sensor 1/3”. Monochrome icx4...

  • Page 51

    Cm-030 ge / cb-030 ge ir-cut & optical low pass filter built in (only for cb-030ge) dimensions 29 x 44 x 75 mm (hxwxd) weight 125 g 125 g for stable operation within the above specifications, allow approximately 30 minutes warm up. Note: above specifications are subject to change without notice - 50...

  • Page 52

    Cm-030 ge / cb-030 ge 12. Appendix precautions personnel not trained in dealing with similar electronic devices should not service this camera. The camera contains components sensitive to electrostatic discharge. The handling of these devices should follow the requirements of electrostatic sensitive...

  • Page 53

    Cm-030 ge / cb-030 ge references 1. This manual can for cm-030ge / cb-030ge can be downloaded from www.Jai.Com 2. Datasheet for cm-030ge / cb-030ge can be downloaded from www.Jai.Com 3. Camera control software can be downloaded from www.Jai.Com 4. Specifications for the ccd sensor sony icx-424al and...

  • Page 54

    Cm-030 ge / cb-030 ge index a l auto iris lens................................... - 24 - lens mount ..................................... - 50 - lvds .............................................. - 6 - b n bayer mosaic color ..............................- 3 - network interface cards..................

  • Page 55

    Cm-030 ge / cb-030 ge 13. User's record camera type: cm-030ge / cb-030ge revision: …………….. Serial no. …………….. Firmware version. …………….. For camera revision history, please contact your local jai distributor. User's mode settings. User's modifications. Declaration of conformity as defined by the coun...