Operation manual double speed progressive scan ccd camera cv-m40 (rev.C).
2 cv-m40 declaration of conformity as defined by the council directive 89/336/eec emc (electromagnetic compatibility) we herewith declare that this product complies with the following provisions applying to it. En-50081-1 en-50082-1.
Cv-m40 3 table of contents ce declaration ............................................................................................................................. 2 1. General ..........................................................................................................................
4 cv-m40 1. General the cv-m40 is a 1/2” ccd progressive scan camera, incorporating double speed and partial scan techniques, housed in a compact and robust package. Using the latest ccd sensor technology with square pixels provides excellent resolution and signal to noise ratio, together with flexi...
Cv-m40 5 4. Locations and functions 1. Ccd sensor 2. Lens mount 3. Bnc connector 4. Sw1 switch 5. 6 pin multi connector 6. 12 pin multi connector 7. Gain potentiometer 8. Tripod mount plate 9. Screw holes for tripod mount plate : : : : : : : 1/2 “ it ccd sensor c-mount type video output (vs 1.0 vpp ...
6 cv-m40 5. Pin assignment 5-1. 12 pin connector (dc in/sync connector) hr10a-10r-12pb-01 (hirose) male * note : to change the signal output on pin no. 6, 7 and 9, it is necessary to make jumper setting. See “7-2. Jumpers on board” for more informations. Pin no. Factory pre-set others 6 hd input hd ...
Cv-m40 7 5-2. 6 pin connector (trigger connector) hr10a-7r-6p (hirose) male * note : to change the signal output on pin no. 5 and 6, it is necessary to make jumper setting. See “7-2. Jumpers on board” for more informations. When trigger signal is input at #5 of 6 pin multi connector, do not input/ou...
8 cv-m40 to output int. Hd/vd signal, make jumper jp9/jp11 open-circuited, and jp12/jp13 short- circuited. All jumpers are located on pk8273 board. Please refer to 7-2-3. Jumpers on pk8273 board. B) output of internal hd/vd signal int. Hd/vd signal is effective only at 75 ohm termination. 6-2. Ext. ...
Cv-m40 9 set sw1-5 at on, and sw1-6 at off to select the edge pre-select mode. Set sw1-1 to sw1-3 to select the appropriate shutter speed. For controlling the shutter speed by the rs 232c serial interface, set sw1-8 at on. Set the sw1-4 switch to on to select the binning mode and set the switch sw1-...
10 cv-m40 note 1:sync or hd is not mentioned note 2:1h=31.777 s note 3:wen polarity can be chosen at jp22 of i/f board 492h valid period 242h valid period 8.5h 10h 7h 10h 3h 1h 18h 8h 7h 1h 1h 9h 15h 2-a) normal readout(1/60sec.1frm=525h,60frm/sec.) 2-b) binning readout(1/120sec.1frm=262h,120frm/sec...
Cv-m40 11 2-c) partial scan valid period effective readout line a b c 240 line 44h 240h 11h 120 line 65h 120h 15h 60 line 79h 60h 17h 30 line 86h 30h 18h note 1:sync or hd is not mentioned note 2:1h=31.777 s note 3:wen polarity can be chosen at jp22 of i/f board ext.Vd int.Vd video out wen (positive...
12 cv-m40 trig xsub enlarged note : the following charts discribes the delay of the exposure exposure time 1.4 ~ 1.5 sec. Note 1:sync or hd is not mentioned note 2:1h=31.777 s note 3:wen polarity can be chosen at jp22 of i/f board 0.032ms 40ms ext.Trig video out wen(positive) wen(negative) valid per...
Cv-m40 13 4.Pulse width control mode note 1:sync or hd is not mentioned note 2:1h=31.777 s note 3:wen polarity can be chosen at jp22 of i/f board waiting for ext.Trigger waiting for ext.Trigger valid period valid period ext.Trig video out wen(positive) wen(negative) ext.Trig video out wen(positive) ...
14 cv-m40 effective readout line a b c 240 line 45h 240h 13h 120 line 66h 120h 17h 60 line 80h 60h 19h 30 line 87h 30h 20h note 1:sync or hd is not mentioned note 2:1h=31.777 s note 3:wen polarity can be chosen at jp22 of i/f board 5-c) partial scan ext.Trig video out wen(positive) wen(negative) val...
Cv-m40 15 7-1. Sw1 switch on the rear panel 7. Mode setting note : the above switches are set at off position by factory pre-set. 7-1-1. Shutter speed (sw1-1, sw1-2, sw1-3) sw1-1, sw1-2 and sw1-3 switches are effective only when the sw1-8 switch is set at off position. Exposing the ccd to direct or ...
16 cv-m40 7-1-2. Binning mode (sw1-4) this switch selects the binning mode. Off on : : normal mode (60 frames/sec.) binning mode (120 frames/sec.) at the binning mode, please note that vertical resolution would be lower (1/2 approx.) of normal mode. 7-1-3. Ext. Trigger/readout modes (sw1-5, sw1-6) t...
Cv-m40 17 7-2. Jumpers on board 7-2-2. Jumpers on pk8202 board jumpers jp5, jp6 and jp7 enable or disable the ext. Trigger input, the wen output and pixel clock output, respectively. 7-2-1. Jumpers on pk8201 board jumpers jp1 and jp2 are used to select the gamma setting. See table below for options....
18 cv-m40 7-2-3. Jumpers on pk8273 board a) jumpers jp8 thru jp13 control the input/output state as well as the termination of the hd and vd signals on pin #6 and #7 of the 12 pin connector. B) jumpers jp14 thru jp17 control the effective number of lines in the partial scan mode. Note : partial scan...
Cv-m40 19 c) jp22 wen polarity reversing when jp22 is set to open, wen is output, and only 1h period becomes high level before video output starts. The periods from wen output and video start may differ at each mode. When jp22 is set to short, wen’s image output period becomes low level, and after f...
20 cv-m40 8. External appearance unit : mm (inch).
Cv-m40 21 9. Specification note : above specifications are subject to change without notice. Model name cv-m40 scanning system 525 lines, 60 frames/sec. Ccd sensor monochorme 1/2" it ccd sensor progressive scan sensing area for video out 6.4 mm (h) x 4.8 mm (v) effective pixels 659 (h) x 494 (v) cel...
22 cv-m40 10. Appendix 10.1. Precautions personnel not trained in dealing with similar electronic devices should not service this camera. The camera contains components sensitive to electrostatic discharge. The handling of these devices should follow the requirements of electrostatic sensitive compo...
Cv-m40 23 this manual can be downloaded from: www.Jai.Com 11. User’s record camera type: cv-m40 scanning system: eia revision: (revision c) serial no. ................. Users mode settings users modifications.
2700-11114 e c1 0701 t he m echademic c ompany jai america, inc., usa suite 450 23046 avenida de la carlota laguna hills, ca 92653 usa phone +1 949 472 5900 fax +1 949 472 5908 www.Jai.Com jai corporation, japan german industry center 1-18-2 hakusan, midori-ku yokohama, kanagawa 226-0006, japan phon...
