- DL manuals
- JAI
- Color Camera
- Elite EL-2800C-GE2
- User manual
JAI Elite EL-2800C-GE2 User manual
Summary of Elite EL-2800C-GE2
Page 1
1052e-1403 elite series el-2800m-ge2 el-2800c-ge2 2.8m digital progressive scan monochrome and color camera document version: ver.1.1 el-2800-ge2_ver.1.1_aug2014 user manual.
Page 2
El-2800m-ge2 / el-2800c-ge2 - 2 - notice t he material contained in this manual consists of information that is proprietary to jai ltd., japan and may only be used by the purchasers of the product. Jai ltd., japan makes no warranty for the use of its product and assumes no responsibility for any err...
Page 3
El-2800m-ge2 supplement the following statement is related to the regulation on “ measures for the administration of the control of pollution by electronic information products “ , known as “ china rohs “. The table shows contained hazardous substances in this camera. Mark shows that the environment...
Page 4
El-2800c-ge2 supplement the following statement is related to the regulation on “ measures for the administration of the control of pollution by electronic information products “ , known as “ china rohs “. The table shows contained hazardous substances in this camera. Mark shows that the environment...
Page 5
El-2800m-ge2 / el-2800c-ge2 - 3 - - contents - introduction ....................................................................................- 7 - before using gige vision ® camera ..........................................................- 7 - 1 jai gige vision ® camera operation manuals ..........
Page 6
El-2800m-ge2 / el-2800c-ge2 - 4 - 5.6.2 pulse generator selector ................................................................... - 39 - 5.6.3 pulse generator length ..................................................................... - 39 - 5.6.4 pulse generator start point .......................
Page 7
El-2800m-ge2 / el-2800c-ge2 - 5 - 7.2.2 exposure time ................................................................................ - 62 - 7.2.3 exposure auto ................................................................................. - 62 - 7.3. Trigger mode ..................................
Page 8
El-2800m-ge2 / el-2800c-ge2 - 6 - 9. Camera setting ......................................................................... - 84 - 9.1 camera control tool .............................................................................. - 84 - 10. External appearance and dimensions .....................
Page 9
El-2800m-ge2 / el-2800c-ge2 - 7 - introduction before using gige vision ® camera all software products described in this manual pertain to the proper use of jai gige vision ® cameras. Product names mentioned in this manual are used only for the explanation of operation. Registered trademarks or trad...
Page 10
El-2800m-ge2 / el-2800c-ge2 - 8 - 4 recommended pc to be used the pc used should have the following performance or better 1) recommended cpu : core i3 or better, 2) recommended memory: ddr3, 4gb fully equipped (windows 7 32-bit) ddr3, 8gb fully equipped (windows 7 64-bit) 3) graphics card : should a...
Page 11
El-2800m-ge2 / el-2800c-ge2 - 9 - camera operation manual 1. General the el-2800m-ge2 and el-2800c-ge2 are new cameras in jai’s elite series. They provide high picture quality, such as high sensitivity and low noise, suitable for machine vision applications. The el-2800m-ge2 is a monochrome progress...
Page 12
El-2800m-ge2 / el-2800c-ge2 - 10 - 3. Main features new elite series, 2/3” progressive scan camera intelligent body design for easy and flexible installation utilizes gigevision 2.0 interface using two rj-45 connectors aspect ratio 4:3, 1920(h) x 1440(v), 2.8 million effective pixels 4.54 μm square ...
Page 13
El-2800m-ge2 / el-2800c-ge2 - 11 - 4. Locations and functions 4.1 locations and functions lens mount c-mount (note *1) 10-pin connector aux connector for lens control (standard) led indicator for power and trigger input 12-pin connector dc and trigger input led (link) gige network indicati...
Page 14
El-2800m-ge2 / el-2800c-ge2 - 12 - 4.2 rear panel the rear panel mounted led provides the following information: amber: power connected – initiating this light goes off after initiating. Steady green: camera is operating in continuous mode flashing green: the camera is receiving external triggering ...
Page 15
El-2800m-ge2 / el-2800c-ge2 - 13 - 5. Input and output 5.1 gige interface 5.1.1 gige vision 2.0 extension functions el-2800-ge2 complies with gige vision 2.0. Its extension functions are described below. 5.1.1.1 link aggregation by handling two ports as one port, the maximum transfer rate can be ach...
Page 16
El-2800m-ge2 / el-2800c-ge2 - 14 - camera port #1 port #a port #b port #0 pc (1) sl(single link) connection camera port #0 port #1 port #a port #b pc camera port #1 port #a port #b pc camera port #1 port #a port #b port #0 pc port #0 sl(sin gle lin k)• @conn ection camera port #0 port #1 port #a por...
Page 17
El-2800m-ge2 / el-2800c-ge2 - 15 - 5.1.1.2 ptp (ieee 1588-2008:precision time protocol） table 3. Specifications equipped functions only slave master function is not equipped used transport multicast udp datagram but, delay_req and delay_resp are unicast udpdatagram in ieee1588, various transport inc...
Page 18
El-2800m-ge2 / el-2800c-ge2 - 16 - 5.1.1.4 notes for connecting 100base-tx in order to use 100 mbps network, 100base-tx and full duplex are available. Half duplex cannot be used. In the case of connecting on 100base-tx, the maximum packet size should be 1500 bytes. In the case of connecting on 100ba...
Page 19
El-2800m-ge2 / el-2800c-ge2 - 17 - on the search downloads page, select your operating system -- in this case windows 7. Select either 32-bit or 64-bit version. After downloading the driver, double-click prowin32.Exe or prowin64.Exe to install the driver..
Page 20
El-2800m-ge2 / el-2800c-ge2 - 18 - after installing the driver, it is possible to confirm version information about the driver in the listing on the “programs and features” page. 2. Setting of nic properties 2.1 settings of each port. Open the “device manager” and find the network adapter, intel pro...
Page 21
El-2800m-ge2 / el-2800c-ge2 - 19 - set jumbo frame (jumbo packet) to 9014 bytes. Select “performance options” and click the “properties” button..
Page 22
El-2800m-ge2 / el-2800c-ge2 - 20 - in setting(s) box, set “interrupt moderation rate” to “extreme.” set “receive buffers” at 2048. 2.2 settings of “teaming” open “teaming” tab. Check “team this adapter with other adapters” and click “new team” button..
Page 23
El-2800m-ge2 / el-2800c-ge2 - 21 - input “team” name, if necessary, otherwise leave it as is. Then click “next”. The “select adapters to include in this team” dialog will open. The adapter with its properties dialog currently open will already be checked. Check the other adapter, in this case, intel...
Page 24
El-2800m-ge2 / el-2800c-ge2 - 22 - “team type selection” will open. In the sp-5000-ge2, only “static link aggregation” and “ieee 802.3ad dynamic link aggregation” are available. In this example, “static link aggregation” is selected. Then click “next”. The confirmation message for creating new team ...
Page 25
El-2800m-ge2 / el-2800c-ge2 - 23 - the following are the “team 0” properties. 3. Jai sdk install after “teaming” of nic is completed, the jai sdk must be installed..
Page 26
El-2800m-ge2 / el-2800c-ge2 - 24 - accept license and click “next” 」 fill in the fields if needed. Then click “next”. This screen confirms whether or not the jai gige vision filter driver is to be installed. When gige vision cameras are used, this must be checked..
Page 27
El-2800m-ge2 / el-2800c-ge2 - 25 - set the folder to install. If the default setting is ok, just click “next”. Select a setup type. If “complete” is ok, then click “next”. Click the “install” button to start installation..
Page 28
El-2800m-ge2 / el-2800c-ge2 - 26 - click “yes” to restart the pc. After restarting, check to see that the filter driver is in the local area network. In the following example, two port names of the intel pro 1000 pt dual port server adapter are re-named. (gige_port and number) if the team name used ...
Page 29
El-2800m-ge2 / el-2800c-ge2 - 27 - in the properties window of the local area network which is to be teamed, the jai gige vision filter driver is initially checked. After “teaming,” jai gige vision filter drivers are not checked in the properties of port 1 and port 2 of the intel pro 1000 pt dual po...
Page 30
El-2800m-ge2 / el-2800c-ge2 - 28 - in jai sdk 2.0.X, the settings window is updated with the applicable camera interface settings. Settings button.
Page 31
El-2800m-ge2 / el-2800c-ge2 - 29 - in jai sdk 2.0.X, “buffer count” and “enable packet resend” are found under the genicam (gentl) settings as a device layer property, while they are found in the settings dialog in the jai sdk 1.4.1 camera control tool. These settings can be set every time the camer...
Page 32
El-2800m-ge2 / el-2800c-ge2 - 30 - 5.2 connectors and pin assignment 5.2.1 output connector for gigabit ethernet type： rj-45 fig.3 rj-45 connector the digital output signals follow the gigabit ethernet interface using an rj-45 conforming connector. The following table shows pin configuration. Table ...
Page 33
El-2800m-ge2 / el-2800c-ge2 - 31 - 5.2.3 aux standard hirose 10-pin connector for lens type : hirose 10-pin connector 3260-10s3(55) fig.5 hirose 10-pin connector table – 3 hirose 10p pin assignment no i/o name note 1 o drive iris+ motorized lens 2 o drive focus+ motorized lens 3 o drive zoom+ motori...
Page 34
El-2800m-ge2 / el-2800c-ge2 - 32 - 5.2.5 aux type 3 hirose 10-pin connector (factory option) hirose 10-pin connector 3260-10s3(55) note: this is a factory option. Table – 5 hirose 10p pin assignment (option) no i/o name note 1 o ttl out2 line8 2 o ttl out3 line9 3 i ttl_in2 line10 4 nc 5 gnd 6 i lvd...
Page 35
El-2800m-ge2 / el-2800c-ge2 - 33 - 5.4.1 line selector in the line selector, the following input and output signals can be assigned. Table – 7 line selector note: line 8 and 9 are available if aux type 3 is used for aux connector (option). 5.4.2 line source line source signal is selected against the...
Page 36
El-2800m-ge2 / el-2800c-ge2 - 34 - 5.4.3 line mode indicates the status of the interface, input or output. 5.4.4 line inverter sets the polarity of the selected input or output. 5.4.5 line status indicates the status of the selected signal, input or output (true=high or false=low) 5.4.6 line format ...
Page 37
El-2800m-ge2 / el-2800c-ge2 - 35 - soft trigger lval in fval in exposure active frame trigger wait frame active gpio 6 (opt in 2) gpio 11 (lvds in) pixel clock cross point switch 12 bit counter inv inv inv n nand inv non inv pulse generator 20 bit counter x 4 clr sel bit (5,0) sel bit (7) sel bit (7...
Page 38
El-2800m-ge2 / el-2800c-ge2 - 36 - table - 9 gpio in and out matrix selector (cross point switch output) source signal (cross point switch input) low high line 5 - 12p opt in 1 line 6 - 12p opt in 2 nand 1 out 1 nand 2 out 1 pulse generator 0 pulse generator 1 pulse generator 2 pulse generator 3 sof...
Page 39
El-2800m-ge2 / el-2800c-ge2 - 37 - 5.5 optical interface el-2800-ge2 is equipped with opto-isolated inputs and outputs, providing galvanic separation between the camera’s inputs/outputs and peripheral equipment. In addition to galvanic separation, the opto-isolated inputs and outputs can cope with a...
Page 40
El-2800m-ge2 / el-2800c-ge2 - 38 - 5.5.3 characteristics of optical interface the relationship of the input signal to the output signal through the optical interface is as follows. 270Ω user power（vcc） 3.3v 5v 12v 24v time delay rise tdr (us) 0.54 0.54 0.62 0.68 rise time rt (us) 1.2 1.2 2 3 time de...
Page 41
El-2800m-ge2 / el-2800c-ge2 - 39 - 5.6.1 clock pre-scaler clock pre-scaler (divide value) can set the dividing value of the frequency divider (12-bit length) and the pixel clock is used for this. Four built-in pulse generators work by the same clock. In the el-2800m/c-ge2, the internal pixel clock i...
Page 42
El-2800m-ge2 / el-2800c-ge2 - 40 - 5.6.5 pulse generator end point set the active output ending count value for the selected pulse generator. 5.6.6 pulse generator repeat count set the repeating number of the pulse for the selected pulse generator. After trigger clear signal is input, the pulse gene...
Page 43
El-2800m-ge2 / el-2800c-ge2 - 41 - 5.6.9 pulse generator clear source the following sources can be selected as the pulse generator clear signal. Table - 12 pulse generator clear source pulse generator clear source item description low connect low level signal to clear source for the selected pulse g...
Page 44
El-2800m-ge2 / el-2800c-ge2 - 42 - 5.6.10 pulse generator inverter clear source signal can have polarity inverted. 5.6.11 pulse generator setting table table - 13 pulse generator setting parameters display name value clock pre-scaler 1 to 4096 pulse generator clock (mhz) [internal pixel clock:54 mhz...
Page 45
El-2800m-ge2 / el-2800c-ge2 - 43 - 6. Sensor layout, output format and timing 6.1 sensor layout ccd sensors used in the el-2800m-ge2 and el-2800c-ge2 have the following tap and pixel layout. 6.1.1 monochrome sensor tap 3 tap 4 tap 2 tap 1 1920 pixels 14 40 p ix el s f fig.11 monochrome sensor layout...
Page 46
El-2800m-ge2 / el-2800c-ge2 - 44 - 6.2. Sensor readout (sensor tap geometry) the following drawings show how the image is read out from the sensor. This is different from how the image is read out from the camera. 6.2.1 4 taps readout (1x2–2ye) fig.13 sensor readout 4-tap 6.3 el-2800-ge2 pixel forma...
Page 47
El-2800m-ge2 / el-2800c-ge2 - 45 - 6.3.1.5 gvsp_pix_mono12_packed 4 5 6 7 8 9 0 1 2 3 0 1 4 5 6 7 8 9 2 3 y0 y1 y2 y3 10 11 10 11 4 5 6 7 8 9 0 1 2 3 10 11 0 1 4 5 6 7 8 9 2 3 10 11 6.3.2 el-2800-ge2 pixel formats 6.3.2.1 gvsp_pix_bayrg8 odd line 0 1 2 3 4 5 6 7 0 1 2 3 4 5 6 7 0 1 2 3 4 5 6 7 r0 g1...
Page 48
El-2800m-ge2 / el-2800c-ge2 - 46 - 6.3.2.5 gvsp_pix_bayrg12_packed odd line 4 5 6 7 8 9 0 1 2 3 0 1 4 5 6 7 8 9 2 3 r0 g1 10 11 10 11 even line 4 5 6 7 8 9 0 1 2 3 0 1 4 5 6 7 8 9 2 3 g0 b1 10 11 10 11 6.3.2.6 gvsp_pix_rgb8_packed (24-bit) 0 1 2 3 4 5 6 7 0 1 2 3 4 5 6 7 0 1 2 3 4 5 6 7 r0 g0 b0 6.3...
Page 49
El-2800m-ge2 / el-2800c-ge2 - 47 - 6.4 output timing 6.4.1 horizontal timing 6.4.1.1 output format (vertical binning off) ob ob ob 102 20 5 5 20 960 412clk = exposure start line 1422clk = exposure start line 316clk = other line 1326clk = other line lval dval video (tap 1,tap 2 /tap3,tap4) exposure a...
Page 50
El-2800m-ge2 / el-2800c-ge2 - 48 - 6.4.2 vertical timing 6.4.2.1 output format (vertical binning off) ob ob 6l(min) 720l 1,2,3, 11,12,13 728,729,730 1460,1459 1449,1448,1447 733,732,731 18l 8l 10l fval dval video tap1 video tap2 fig.22 vertical timing (vertical timing off) 6.4.2.2 output format (ver...
Page 51
El-2800m-ge2 / el-2800c-ge2 - 49 - 7. Operating modes 7.1. Acquisition control 7.1.1 acqusition mode in the el-2800m-ge2 and el-2800c-ge2, the following three acquisition modes are available. Single frame : one frame can be output by acqusitionstart command multi frames : the number of frames which ...
Page 52
El-2800m-ge2 / el-2800c-ge2 - 50 - the following diagrams show the single frame timing relationships. Conditions: acquisition mode: single trigger selector: acquisition start trigger mode: off note: signals shown in ( ) describe the internal operation of the camera. Fig.26 single frame timing fval(s...
Page 53
El-2800m-ge2 / el-2800c-ge2 - 51 - conditions: acquisition mode: single trigger selector: acquisition start trigger mode: on fig. 27 single frame timing fval(sensor read out) acquisition trigger wait frame trigger wait acquisition active exposure active frame active (sensor exposure) (stream active)...
Page 54
El-2800m-ge2 / el-2800c-ge2 - 52 - conditions: acquisition mode: single trigger selector: frame start trigger mode: on fig. 28 single frame timing fval(sensor read out) acquisition trigger wait frame trigger wait acquisition active exposure active frame active sensor exposure stream active acquisiti...
Page 55
El-2800m-ge2 / el-2800c-ge2 - 53 - 7.1.1.2 multiframe in this mode, the acquisitionstart command captures the number of frames which are specified by acquisitionframecount. ◆ normal multi-frame operation 1) acquisitionstart command is input 2) acquisitiontriggerwait becomes effective 3) acquisitiona...
Page 56
El-2800m-ge2 / el-2800c-ge2 - 54 - the following diagrams show the multi frame timing relationships. Conditions: acquisition mode: multi trigger selector: acquisition start acquisition frame count: 2 trigger mode: off fig.29 multi frame timing fval(sensor read out) acquisition trigger wait frame tri...
Page 57
El-2800m-ge2 / el-2800c-ge2 - 55 - conditions: acquisition mode: multi trigger selector: acquisition start acquisition frame count: 2 trigger mode: on fig.30 multi frame timing fval(sensor read out) acquisition trigger wait frame trigger wait acquisition active exposure active frame active (sensor e...
Page 58
El-2800m-ge2 / el-2800c-ge2 - 56 - conditions: acquisition mode: multi trigger selector: frame start acquisition frame count: 2 trigger mode: on fig.31 multi frame timing (frame start on) fval(sensor read out) acquisition trigger wait frame trigger wait acquisition active exposure active frame activ...
Page 59
El-2800m-ge2 / el-2800c-ge2 - 57 - 7.1.1.3 continuous mode in this mode, when the acquisitionstart command is set, the image is continuously output at the current frame rate. This is the default setting for the el-2800m-ge2 and el-2800c-ge2. 1) acquisitionstart command is input 2) acquisitiontrigger...
Page 60
El-2800m-ge2 / el-2800c-ge2 - 58 - conditions: acquisition mode: continuous trigger selector: acquisition start trigger mode: on fig. 33 continuous timing fval(sensor read out) acquisition trigger wait frame trigger wait acquisition active exposure active frame active (sensor exposure) (stream activ...
Page 61
El-2800m-ge2 / el-2800c-ge2 - 59 - conditions: acquisition mode: continuous trigger selector: frame start trigger mode: on fig.34 continuous timing fval(sensor read out) acquisition trigger wait frame trigger wait acquisition active exposure active frame active (sensor exposure) (stream active) acqu...
Page 62
El-2800m-ge2 / el-2800c-ge2 - 60 - 7.1.2 acquisition frame rate with trigger off, which is free-running operation, it is possible to set a longer acquisition period than the time required to read out all pixels in the area set by the roi command. The setting is done in the acquisition frame rate. Th...
Page 63
El-2800m-ge2 / el-2800c-ge2 - 61 - 7.1.4.2 v binning on the frame rate is the smaller of the sensor frame rate or the network frame rate. Sensor frame rate (fps) = 1000000/〔［ (height/2) + {(360-(height/2)-1)/2} + 16 ］ × 29.296 〕 or network_frame_rate(hz) = network_bit_rate / [{(width × height × bits...
Page 64
El-2800m-ge2 / el-2800c-ge2 - 62 - the effect of the combination of exposure mode, trigger option and trigger mode is as follows. Table20. The combination of exposure mode, trigger option and trigger mode exposure mode trigger option trigger mode (frame start) operation off n/a n/a self-running oper...
Page 65
El-2800m-ge2 / el-2800c-ge2 - 63 - 7.3. Trigger mode 7.3.1 trigger source the following signals can be used as the trigger source signal. Signal description software signal generated by trigger software command pulse generator 0 to 3 signal generated by pulse generator 0 to 3 line 5 signal which is ...
Page 66
El-2800m-ge2 / el-2800c-ge2 - 64 - 7.5. Timed mode (eps) this mode allows a single image frame to be captured with a preset exposure time by using the external trigger. Additional settings determine if the trigger pulse can be accepted during the exposure period. Primary settings to use this mode ex...
Page 67
El-2800m-ge2 / el-2800c-ge2 - 65 - 7.5.2 if the overlap setting is “readout” trigger ccd exposure fval exposure active exposure period t3 t1 t2 fig.36 readout t1 t2 t3 2l (min) 1l 4.5l ～5.5l.
Page 68
El-2800m-ge2 / el-2800c-ge2 - 66 - 7.6. Trigger width mode in this mode, the exposure time is equal to the trigger pulse width. Accordingly, longer exposure times are supported. Additional settings determine if the trigger pulse can be accepted during the exposure period. Primary settings to use thi...
Page 69
El-2800m-ge2 / el-2800c-ge2 - 67 - 7.6.2 if the overlap setting is “readout” trigger ccd exposure fval exposure active exposure period t3 t1 t2 t4 fig.38 readout t1 t2 t3 t4 2l (min) 1l 4l 1l.
Page 70
El-2800m-ge2 / el-2800c-ge2 - 68 - 7.7. Rct mode until the trigger is input, the camera operates continuously and the video signal for the auto-iris lens is output. At this moment, the video signal, fval and lval are output but dval is not output. When the trigger is input, the fast dump is activate...
Page 71
El-2800m-ge2 / el-2800c-ge2 - 69 - 7.8. Piv (particle image velocimetry) the particle image velocimetry mode can be used in applications where 2 images need to be taken with a very short time interval. It can only be used with strobe flash as illumination. The first accumulation time is 10 sec to 2 ...
Page 72
El-2800m-ge2 / el-2800c-ge2 - 70 - 7.9. Sequential timed exposure mode 7.9.1 video send mode the sequential trigger mode has the following modes and it is selected in the video send mode. Depending on the mode selected, a different method is used to select the sequence index. Trigger sequence: selec...
Page 73
El-2800m-ge2 / el-2800c-ge2 - 71 - (3) sequence roi height set the height of sequence roi. The setting range is 8 to 1440 lines. Rules for setting area and step number are the same as the normal roi mode set by [video send mode] = “normal”. (4) sequence roi offset y set offset y of sequence roi. Seq...
Page 74
El-2800m-ge2 / el-2800c-ge2 - 72 - fig. 42 sequence trigger timing 7.10. Operation and function matrix table - 24 operation and function matrix exposure operation trigger mode timed option v. Binning (note1) h. Binning (note1) exposu re time roi (partial scan) sequenc e roi (video send mode) auto wh...
Page 75
El-2800m-ge2 / el-2800c-ge2 - 73 - 8. Other functions 8.1 black level control this function adjusts the setup level. Variable range: -256 to 255 lsb (at 10-bit output) 8.1.1 black level selector the following factors can be set. El-2800m: digitalall/tap1all/tap2all/tap3all/tap4all el-2800c: digitala...
Page 76
El-2800m-ge2 / el-2800c-ge2 - 74 - the magnification of digital gain is calculated in the following formula. Fig. 44 gain control 8.2.1 gain selector the following parameters can be set. El-2800m: analogall/digitalall/digital tap2/digital tap3/digital tap4 el-2800c: analogall/digitalall/digital red ...
Page 77
El-2800m-ge2 / el-2800c-ge2 - 75 - el-2800c: analogall：1.0～22.555 digitalall：0.7079～1.4125 digital red all：0.4466～3.1623 digital blue all：0.4466～3.1623 digital tap2all：0.8912～1.1220/ digital tap2red：0.8912～1.1220/ digital tap2blue：0.8912～1.1220 digital tap3all：0.8912～1.1220/ digital tap3red：0.8912～1...
Page 78
El-2800m-ge2 / el-2800c-ge2 - 76 - fig.45 alc channel area 8.2.5 balance white auto this is the auto white balance control function. The operation can be selected from the following: off: adjust manually. Once: operate only one time when this command is set continuous: operate the white balance cont...
Page 79
El-2800m-ge2 / el-2800c-ge2 - 77 - output data = video in x lut data 8.4. Gamma this command is used to set gamma between gamma 0.45 and gamma 1.0 (off). The gamma can be changed in 16 steps. The gamma value is an approximate value. Fig. 46 gamma compensation 8.5. Shading correction this function co...
Page 80
El-2800m-ge2 / el-2800c-ge2 - 78 - adjustable range less 30% fig. 47 flat shading correction concept drawing color shading correction (for el-2800c only): in this case, r channel and b channel are adjusted to match with g channel characteristics. The block grid for compensation is 15(h) x 12(v) bloc...
Page 81
El-2800m-ge2 / el-2800c-ge2 - 79 - fig. 49 blemish compensation note: if defective pixels are found consecutively in the horizontal direction, the blemish compensation circuit does not work. 8.7. Bayer color interpolation (only for el-2800c) this function is available only for el-2800c-ge2. The el-2...
Page 82
El-2800m-ge2 / el-2800c-ge2 - 80 - 8.8 lens the el-2800-ge2 can be used with 4 different types of auto iris lenses, in addition to standard lenses with manual iris control. If an auto iris function is to be utilized, the lens type used must be selected in lens select. Table -25 lens selector lens se...
Page 83
El-2800m-ge2 / el-2800c-ge2 - 81 - 8.8.2.2 step max. The iris control step depends on the lens. The setting value uses the value stored in the camera. Refer to the table above for the control step number. 8.8.2.3 position the iris position can be set between 0 to step max. 0 means to open the iris a...
Page 84
El-2800m-ge2 / el-2800c-ge2 - 82 - 8.8.3.3 focus+ near: while this command is supplied, the focus will continue to shift closer to the camera. Far: while this command is supplied, the focus will continue to move towards infinity. Stop: when this command is supplied, the focus operation stops. 8.8.4 ...
Page 85
El-2800m-ge2 / el-2800c-ge2 - 83 - gain is fixed at min. Dark light changes bright auto shutter max auto shutter operation max ～ min (user set) auto shutter fixed at min iris diaphragm fixed (open) auto iris operation agc works: auto shutter works: auto iris works: agc operation max ～ min (user set)...
Page 86
El-2800m-ge2 / el-2800c-ge2 - 84 - 9. Camera setting 9.1 camera control tool in the el-2800m-ge2 and el-2800c-ge2, control of all camera functions is done by the jai sdk and control tool software. All controllable camera functions are stored in an xml file inside of the camera. The jai sdk and contr...
Page 87
El-2800m-ge2 / el-2800c-ge2 - 85 - 10. External appearance and dimensions fig. 54 outside dimensions (c mount).
Page 88
El-2800m-ge2 / el-2800c-ge2 - 86 - 11. Specifications 11.1 spectral response fig. 55 spectral response (el-2800m-ge2) fig.56 spectral response (el-2800c-ge2).
Page 89
El-2800m-ge2 / el-2800c-ge2 - 87 - 11.2 specifications table table - 26 specifications table specifications el-2800m-ge2 el-2800c-ge2 scanning system progressive scan, 4-tap synchronization internal interface 1000base-t ethernet (gige vision 2.0) x 2ports (100base-t can be used) complies with single...
Page 90
El-2800m-ge2 / el-2800c-ge2 - 88 - trigger selector acquisition start / acquisition end / frame start trigger overlap off / readout trigger option off, jai_rct(w/alc), jai_piv, sequence trigger trigger input signal line 5,6, pg0 to 3, soft, option (line 10,11) exposure mode timed 10 μs (min.) ～ 8 se...
Page 91
El-2800m-ge2 / el-2800c-ge2 - 89 - housing dimensions 62 x 62 x 55.5 mm (w x h x d) (excluding protrusion) weight 265 g note1): approximately 5 minutes pre-heating is required to achieve these specifications. Note2): the above specifications are subject to change without notice..
Page 92
El-2800m-ge2 / el-2800c-ge2 - 90 - appendix 1. Precautions personnel not trained in dealing with similar electronic devices should not service this camera. The camera contains components sensitive to electrostatic discharge. The handling of these devices should follow the requirements of electrostat...
Page 93
El-2800m-ge2 / el-2800c-ge2 - 91 - if you mount the tripod mounting plate, please use the provided screws. 5. Exportation when exporting this product, please follow the export regulation of your own country. 6. References 1. This manual can and datasheet for el-2800m-ge2 / el-2800c-ge2 can be downlo...
Page 94
El-2800m-ge2 / el-2800c-ge2 - 92 - manual change history date revision changes april 2014 preliminary new release july 2014 1.0 release aug. 2014 1.1 revise lag settings information.
Page 95
El-2800m-ge2 / el-2800c-ge2 - 93 - user's record camera type: el-2800m-ge2 / el-2800c-ge2 revision: …………….. Serial no. …………….. Firmware version. …………….. For camera revision history, please contact your local jai distributor. User's mode settings. User's modifications. Company and product names menti...