1. DL manuals
  2. JAI
  3. Other
  4. Spark SP-5000C-GE2
  5. User manual

JAI Spark SP-5000C-GE2 User manual

Manual is about: JAI Spark Series 5M Digital Progressive Scan Monochrome and Color Camera

Summary of Spark SP-5000C-GE2

  • Page 1

    1050e-1404 spark series sp-5000m-ge2 sp-5000c-ge2 5m digital progressive scan monochrome and color camera document version: ver.1.3 sp-5000-ge2_ver.1.3_oct2014 user manual.

  • Page 2

    Sp-5000m-ge2 / sp-5000c-ge2 - 2 - notice t he material contained in this manual consists of information that is proprietary to jai ltd., japan and may only be used by the purchasers of the product. Jai ltd., japan makes no warranty for the use of its product and assumes no responsibility for any err...

  • Page 3

    Sp-5000m-ge2 supplement the following statement is related to the regulation on “ measures for the administration of the control of pollution by electronic information products “ , known as “ china rohs “. The table shows contained hazardous substances in this camera. Mark shows that the environment...

  • Page 4

    Sp-5000c-ge2 supplement the following statement is related to the regulation on “ measures for the administration of the control of pollution by electronic information products “ , known as “ china rohs “. The table shows contained hazardous substances in this camera. Mark shows that the environment...

  • Page 5

    Sp-5000m-ge2 / sp-5000c-ge2 - 3 - - contents - introduction ..................................................................................... - 7 - before using gige vision ® camera .......................................................... - 7 - 1 jai gige vision ® camera operation manuals .......

  • Page 6

    Sp-5000m-ge2 / sp-5000c-ge2 - 4 - 5.5.5 pulse generator end point ................................................................... - 40 - 5.5.6 pulse generator repeat count .............................................................. - 40 - 5.5.7 pulse generator clear activation ..................

  • Page 7

    Sp-5000m-ge2 / sp-5000c-ge2 - 5 - 7.3.2 trigger mode ....................................................................................- 66 - 7.3.3 trigger source ..................................................................................- 66 - 7.3.4 trigger activation ........................

  • Page 8

    Sp-5000m-ge2 / sp-5000c-ge2 - 6 - 8.10 hdr (high dynamic range) (sp-5000m-ge2 only) ............................................ - 88 - 9. Camera setting ......................................................................... - 89 - 9.1 camera control tool ............................................

  • Page 9

    Sp-5000m-ge2 / sp-5000c-ge2 - 7 - introduction before using gige vision ® camera all software products described in this manual pertain to the proper use of jai gige vision ® cameras. Product names mentioned in this manual are used only for the explanation of operation. Registered trademarks or trad...

  • Page 10

    Sp-5000m-ge2 / sp-5000c-ge2 - 8 - 4 recommended pc to be used the pc used should have the following performance or better 1) recommended cpu : core i3 or better, 2) recommended memory: ddr3, 4gb fully equipped (windows 7 32-bit) ddr3, 8gb fully equipped (windows 7 64-bit) 3) graphics card : should a...

  • Page 11

    Sp-5000m-ge2 / sp-5000c-ge2 - 9 - camera operation manual 1. General the sp-5000m-ge2 and sp-5000c-ge2 are among the first new spark series cameras to be introduced. They are high performance cameras with high resolution and a fast frame rate suitable for high speed machine vision applications. The ...

  • Page 12

    Sp-5000m-ge2 / sp-5000c-ge2 - 10 - 3. Main features new spark series, 1” progressive scan camera intelligent body design for easy and flexible installation utilizes new gige vision ver.2.0 aspect ratio 5:4, 2560(h) x 2048(v) - 5.2 million effective pixels 5 μm square pixels s/n 55 db for monochrome ...

  • Page 13

    Sp-5000m-ge2 / sp-5000c-ge2 - 11 - 4. Locations and functions 4.1 locations and functions  lens mount c-mount (note *1)  10-pin connector aux connector for lens control (standard)  led indicator for power and trigger input  12-pin connector dc and trigger input  led (link) gige network indicati...

  • Page 14

    Sp-5000m-ge2 / sp-5000c-ge2 - 12 - 4.2 rear panel the rear panel mounted leds provide the following information: power/trig amber: power connected – initiating this light goes off after initiating. Steady green: camera is operating in continuous mode flashing green: the camera is receiving external ...

  • Page 15

    Sp-5000m-ge2 / sp-5000c-ge2 - 13 - 5. Input and output 5.1 gige interface 5.1.1 gigevision 2.0 interface extension sp-5000-ge2 complies with gige vision 2.0. Its extension functions are described below. 5.1.1.1 link aggregation by handling two ports as one port, the maximum transfer rate can be achi...

  • Page 16

    Sp-5000m-ge2 / sp-5000c-ge2 - 14 - camera port #1 port #a port #b port #0 pc (1) sl(single link) connection camera port #0 port #1 port #a port #b pc camera port #1 port #a port #b pc camera port #1 port #a port #b port #0 pc port #0 sl(sin gle lin k)• @conn ection camera port #0 port #1 port #a por...

  • Page 17

    Sp-5000m-ge2 / sp-5000c-ge2 - 15 - 5.1.1.2 ptp (ieee 1588-2008: precision time protocol） table 3. Specifications equipped functions only slave master function is not equipped used transport multicast udp datagram but, delay_req and delay_resp are unicast udp datagram in ieee 1588, various transports...

  • Page 18

    Sp-5000m-ge2 / sp-5000c-ge2 - 16 - 5.1.1.4 notes for connecting 100base-tx in order to use 100 mbps network, 100base-tx and full duplex are available. Half duplex cannot be used. In the case of connecting on 100base-tx, the maximum packet size should be 1500 bytes. In the case of connecting on 100ba...

  • Page 19

    Sp-5000m-ge2 / sp-5000c-ge2 - 17 - on the search downloads page, select your operating system -- in this case windows 7. Select either 32-bit or 64-bit version. After downloading the driver, double-click prowin32.Exe or prowin64.Exe to install the driver..

  • Page 20

    Sp-5000m-ge2 / sp-5000c-ge2 - 18 - after installing the driver, it is possible to confirm version information about the driver in the listing on the “programs and features” page. 2. Setting of nic properties 2.1 settings of each port. Open the “device manager” and find the network adapter, intel pro...

  • Page 21

    Sp-5000m-ge2 / sp-5000c-ge2 - 19 - set jumbo frame (jumbo packet) to 9014 bytes. Select “performance options” and click the “properties” button..

  • Page 22

    Sp-5000m-ge2 / sp-5000c-ge2 - 20 - in setting(s) box, set “interrupt moderation rate” to “extreme.” set “receive buffers” at 2048. 2.2 settings of “teaming” open “teaming” tab. Check “team this adapter with other adapters” and click “new team” button..

  • Page 23

    Sp-5000m-ge2 / sp-5000c-ge2 - 21 - in put “team” name, if necessary, otherwise leave it as is. Then click “next”. The “select adapters to include in this team” dialog will open. The adapter with its properties dialog currently open will already be checked. Check the other adapter, in this case, inte...

  • Page 24

    Sp-5000m-ge2 / sp-5000c-ge2 - 22 - “team type selection” will open. In the sp-5000-ge2, only “static link aggregation” and “ieee 802.3ad dynamic link aggregation” are available. In this example, “static link aggregation” is selected. Then click “next”. The confirmation message for creating new team ...

  • Page 25

    Sp-5000m-ge2 / sp-5000c-ge2 - 23 - the following are the “team 0” properties. 3. Jai sdk install after “teaming” of nic is completed, the jai sdk must be installed..

  • Page 26

    Sp-5000m-ge2 / sp-5000c-ge2 - 24 - accept license and click “next” 」 fill in the fields if needed. Then click “next”. This screen confirms whether or not the jai gige vision filter driver is to be installed. When gige vision cameras are used, this must be checked..

  • Page 27

    Sp-5000m-ge2 / sp-5000c-ge2 - 25 - set the folder to install. If the default setting is ok, just click “next”. Select a setup type. If “complete” is ok, then click “next”. Click the “install” button to start installation..

  • Page 28

    Sp-5000m-ge2 / sp-5000c-ge2 - 26 - click “yes” to restart the pc. After restarting, check to see that the filter driver is in the local area network. In the following example, two port names of the intel pro 1000 pt dual port server adapter are re-named. (gige_port and number) if the team name used ...

  • Page 29

    Sp-5000m-ge2 / sp-5000c-ge2 - 27 - in the properties window of the local area network which is to be teamed, the jai gige vision filter driver is initially checked. After “teaming,” jai gige vision filter drivers are not checked in the properties of port 1 and port 2 of the intel pro 1000 pt dual po...

  • Page 30

    Sp-5000m-ge2 / sp-5000c-ge2 - 28 - in jai sdk 2.0.X, the settings window is updated with the applicable camera interface settings. Settings button.

  • Page 31

    Sp-5000m-ge2 / sp-5000c-ge2 - 29 - in jai sdk 2.0.X, “buffer count” and “enable packet resend” are found under the genicam (gentl) settings as a device layer property, while they are found in the settings dialog in the jai sdk 1.4.1 camera control tool. These settings can be set every time the camer...

  • Page 32

    Sp-5000m-ge2 / sp-5000c-ge2 - 30 - 5.2 connectors and pin assignment 5.2.1 output connector for gigabit ethernet type： rj-45 fig.3 rj-45 connector the digital output signals follow the gigabit ethernet interface using an rj-45 conforming connector. The following table shows pin configuration. Table ...

  • Page 33

    Sp-5000m-ge2 / sp-5000c-ge2 - 31 - 5.2.3 aux standard hirose 10-pin connector 5.2.3.1 figure and pin configuration type : hirose 10-pin connector 3260-10s3(55) fig.5 hirose 10-pin connector table 6. Hirose 10p pin assignment (standard) no i/o name note 1 o drive iris+ motorized lens 2 o drive focus+...

  • Page 34

    Sp-5000m-ge2 / sp-5000c-ge2 - 32 - 5.2.5 aux type 3 hirose 10-pin connector (factory option) type: hirose 10-pin connector 3260-10s3(55) table 8. Hirose 10p pin assignment no i/o name note 1 o ttl out2 line8 2 o ttl out3 line9 3 i ttl_in2 line10 4 nc 5 gnd 6 i lvds_in1+ line11 7 i lvds_in1- 8 nc 9 g...

  • Page 35

    Sp-5000m-ge2 / sp-5000c-ge2 - 33 - table 10. Line source line source item description low connect low level signal to line item selected in line selector, default setting high connect high level signal to line item selected in line selector frame trigger wait connect frame trigger wait signal to lin...

  • Page 36

    Sp-5000m-ge2 / sp-5000c-ge2 - 34 - 5.3.3 line mode indicates the status of the interface, input or output. 5.3.4 line inverter sets the polarity of the selected input or output. 5.3.5 line status indicates the status of the selected signal, input or output (true=high or false=low) 5.3.6 line format ...

  • Page 37

    Sp-5000m-ge2 / sp-5000c-ge2 - 35 - soft trigger lval in fval in exposure active acquisition trigger wait acquisition active frame trigger wait frame active user output 0 user output 1 user output 2 user output 3 action 1 action 2 gpio 5 (opt in 1) gpio 6 (opt in2) gpio 10 (ttl in2) gpio 11 (lvds in)...

  • Page 38

    Sp-5000m-ge2 / sp-5000c-ge2 - 36 - 5.3.7.2 in and out matrix table the following table shows the input and output matrix table. Table 11. Gpio in and out matrix table selector (cross point switch output) source signal (cross point switch input) low high line 5 - 12p opt 1 in line 6 - 12p opt 2 in na...

  • Page 39

    Sp-5000m-ge2 / sp-5000c-ge2 - 37 - 5.4 optical interface sp-5000-ge2 is equipped with opto-isolated inputs and outputs, providing galvanic separation between the camera’s inputs/outputs and peripheral equipment. In addition to galvanic separation, the opto-isolated inputs and outputs can cope with a...

  • Page 40

    Sp-5000m-ge2 / sp-5000c-ge2 - 38 - 5.4.3 characteristics of optical interface the relationship of the input signal to the output signal through the optical interface is as follows. 270Ω user power（vcc） 3.3v 5v 12v 24v time delay rise tdr (us) 0.54 0.54 0.62 0.68 rise time rt (us) 1.2 1.2 2 3 time de...

  • Page 41

    Sp-5000m-ge2 / sp-5000c-ge2 - 39 - 5.5.1 clock pre-scaler clock pre-scaler (divide value) can set the dividing value of the frequency divider (12-bit length) and the pixel clock is used for this. Four built-in pulse generators work by the same clock. In the sp-5000-ge2, the pixel clock is set at 48 ...

  • Page 42

    Sp-5000m-ge2 / sp-5000c-ge2 - 40 - 5.5.4 pulse generator start point set the active output start count value for the selected pulse generator. However, please note that a maximum 1 clock jitter for the clock which is divided in the clock pre-scaler can occur. 5.5.5 pulse generator end point set the ...

  • Page 43

    Sp-5000m-ge2 / sp-5000c-ge2 - 41 - 5.5.9 pulse generator clear source the following clear source can be selected as the pulse generator clear signal. Table14. Pulse generator clear source pulse generator clear source item description low connect low level signal to clear source for the selected puls...

  • Page 44

    Sp-5000m-ge2 / sp-5000c-ge2 - 42 - 5.5.10 pulse generator inverter clear source signal can have polarity inverted. 5.5.11 pulse generator setting parameters table15. Pulse generator setting parameters display name value clock pre-scaler 1 to 4096 pulse generator clock (mhz) [pixel clock:48 mhz]÷[clo...

  • Page 45

    Sp-5000m-ge2 / sp-5000c-ge2 - 43 - 6. Sensor layout, output format and timing 6.1 sensor layout cmos sensors used in the sp-5000m-ge2 and sp-5000c-ge2 have the following tap and pixel layout. 6.1.1 monochrome sensor 2560 pixels 20 48 p ix el s f fig.14 monochrome sensor layout 6.1.2 bayer color sens...

  • Page 46

    Sp-5000m-ge2 / sp-5000c-ge2 - 44 - 6.2. Camera output format the following table shows the relationship between camera output and sensor readout system. Camera output format sensor readout system reference figure 1x–1y 1-tap readout 6.2.1 note: the description of camera output format is based on gen...

  • Page 47

    Sp-5000m-ge2 / sp-5000c-ge2 - 45 - 6.2.2 sp-5000m-ge2 pixel type 6.2.2.1 gvsp_pix_mono8 8-bit output 0 1 2 3 4 5 6 7 0 1 2 3 4 5 6 7 0 1 2 3 4 5 6 7 y0 y1 y2 6.2.2.2 gvsp_pix_mono10 16-bit output x 0 1 2 3 4 5 6 7 8 9 x x x x x x 0 1 2 3 4 5 6 7 y0 y0 y1 9 8 x x x x x x y1 6.2.2.3 gvsp_pix_mono10pac...

  • Page 48

    Sp-5000m-ge2 / sp-5000c-ge2 - 46 - 6.2.3.3 gvsp_pix_baygr10packed 12-bit output odd line 2 3 4 5 6 7 8 9 0 1 x x 0 1 2 3 4 5 6 7 8 9 x x g0 r1 even line 2 3 4 5 6 7 8 9 0 1 x x 0 1 2 3 4 5 6 7 8 9 x x b0 g1 6.2.3.4 gvsp_pix_rgb8_packed (24-bit) 0 1 2 3 4 5 6 7 0 1 2 3 4 5 6 7 0 1 2 3 4 5 6 7 r0 g0 b...

  • Page 49

    Sp-5000m-ge2 / sp-5000c-ge2 - 47 - 6.2.4 pixelsize table16. Pixel size bit per pixel pixel format sp-5000m-ge2 sp-5000c-ge2 bpp8 mono8 bayergr8 bpp12 mono10packed bayergr10packed yuv411packed bpp16 mono10 bayergr10 yuv422packed bpp24 rgb8packed yuv444packed 6.3 output timing 6.3.1 horizontal timing ...

  • Page 50

    Sp-5000m-ge2 / sp-5000c-ge2 - 48 - 6.3.2 vertical timing 6.3.2.1 output format: 1x–1y, vertical binning off 1l = 165 clocks fval dval ccd exposure video exposure active frame active 2048l 47 ～48l(min) 9 ～10l fig.19 vertical timing (vertical binning off) 6.3.2.2 output format: 1x–1y, vertical binning...

  • Page 51

    Sp-5000m-ge2 / sp-5000c-ge2 - 49 - 6.3.3 roi (region of interest) setting in the sp-5000-ge2, a subset of the image can be output by setting width, height, offset-x, and offset-y. If the height is decreased, the number of lines read out is decreased and as the result, the frame rate is increased. Ho...

  • Page 52

    Sp-5000m-ge2 / sp-5000c-ge2 - 50 - 7. Operating modes 7.1. Acquisition control (change the frame rate) 7.1.1 acquisition mode in the sp-5000-ge2, the following three acquisition modes are available. Single frame : one frame can be output by acqusitionstart command multi frames : the number of frames...

  • Page 53

    Sp-5000m-ge2 / sp-5000c-ge2 - 51 - setting condition 1 acquisition mode： single trigger selector： acquisition start trigger mode： off note: on the above timing chart, signals indicated by ( ) describe operation inside the camera. Fig.24 single frame operation timing（1） fval(sensor read out) acquisit...

  • Page 54

    Sp-5000m-ge2 / sp-5000c-ge2 - 52 - setting condition 2 acquisition mode： single trigger selector： acquisition start trigger mode： on fig.25 single frame operation timing (2) fval(sensor read out) acquisition trigger wait frame trigger wait acquisition active exposure active frame active (sensor expo...

  • Page 55

    Sp-5000m-ge2 / sp-5000c-ge2 - 53 - setting condition 3 acquisition mode： single trigger selector： frame start trigger mode： on fig.26 single frame operation timing (3) fval(sensor read out) acquisition trigger wait frame trigger wait acquisition active exposure active frame active sensor exposure st...

  • Page 56

    Sp-5000m-ge2 / sp-5000c-ge2 - 54 - 7.1.1.2 multi frame operation in this mode, the acquisitionstart command captures the number of frames which are specified by acquisitionframecount. ◆ normal multi-frame operation 1) acquisitionstart command is input 2) acquisitiontriggerwait becomes effective 3) a...

  • Page 57

    Sp-5000m-ge2 / sp-5000c-ge2 - 55 - setting condition 1 acquisition mode： multi trigger selector： acquisition start acquisition frame count ： 2 trigger mode： off fig.27 multi frame operation timing (1) fval(sensor read out) acquisition trigger wait frame trigger wait acquisition active exposure activ...

  • Page 58

    Sp-5000m-ge2 / sp-5000c-ge2 - 56 - setting operation 2 acquisition mode： multi trigger selector： acquisition start acquisition frame count： 2 trigger mode： on fig.28 multi frame operation timing (2) fval(sensor read out) acquisition trigger wait frame trigger wait acquisition active exposure active ...

  • Page 59

    Sp-5000m-ge2 / sp-5000c-ge2 - 57 - setting operation 3 acquisition mode： multi trigger selector： frame start acquisition frame count： 2 trigger mode： on fig.29 multi frame operation timing (3) fval(sensor read out) acquisition trigger wait frame trigger wait acquisition active exposure active frame ...

  • Page 60

    Sp-5000m-ge2 / sp-5000c-ge2 - 58 - 7.1.1.3 continuous in this mode, when the acquisitionstart command is set, the image is continuously output at the current frame rate. This is the default setting for the sp-5000m-ge2 and sp-5000c-ge2. 1) acquisitionstart command is input 2) acquisitiontriggerwait ...

  • Page 61

    Sp-5000m-ge2 / sp-5000c-ge2 - 59 - setting operation 1 acquisition mode： continuous trigger selector： acquisition start trigger mode： off fig.30 continuous operation timing (1) fval(sensor read out) acquisition trigger wait frame trigger wait acquisition active exposure active frame active (sensor e...

  • Page 62

    Sp-5000m-ge2 / sp-5000c-ge2 - 60 - setting condition 2 acquisition mode： continuous trigger selector： acquisition start trigger mode： on fig.31 continuous operation timing (2) fval(sensor read out) acquisition trigger wait frame trigger wait acquisition active exposure active frame active (sensor ex...

  • Page 63

    Sp-5000m-ge2 / sp-5000c-ge2 - 61 - setting condition 3 acquisition mode： continuous trigger selector： frame start trigger mode： on fig.32 continuous operation timing (3) fval(sensor read out) acquisition trigger wait frame trigger wait acquisition active exposure active frame active (sensor exposure...

  • Page 64

    Sp-5000m-ge2 / sp-5000c-ge2 - 62 - 7.1.2 acquisition frame rate with trigger off (free running mode – see section 7.2.1), the default frame rate of the camera is based on the specified roi. The smaller the roi, the faster the default frame rate. However, it is possible to specify a free-running fram...

  • Page 65

    Sp-5000m-ge2 / sp-5000c-ge2 - 63 - clock number of 1 line validclocksofline = (clocksofline - addtionalclocks) x (width + 127) / 128 x 128 / 2560 + 1 + addtionalclocks if the result is less than 165, validclocksofline = 165; clock number of 1 frame clocksofframe = (validclocksofline + (binninghorizo...

  • Page 66

    Sp-5000m-ge2 / sp-5000c-ge2 - 64 - 7.2. Exposure settings this section describes how to set the exposure settings. 7.2.1 exposure mode the exposure mode can be selected from the following three ways. Table18. Exposure mode exposure mode setting exposure operation off no exposure control (free-runnin...

  • Page 67

    Sp-5000m-ge2 / sp-5000c-ge2 - 65 - 7.2.2 exposure time this command is effective only when exposure mode is set to timed. It is for setting exposure time. The setting step for exposure time is 1 μsec per step. Minimum: 10 μsec maximum: 8 seconds (note – noise may make image unusuable after 2 seconds...

  • Page 68

    Sp-5000m-ge2 / sp-5000c-ge2 - 66 - 7.3. Trigger control the following 6 types of trigger control are available by the combination of trigger selector, trigger mode, exposure mode and trigger option. Table21. Trigger control 7.3.1 trigger selector selects the trigger operation. In the sp-5000-ge2, th...

  • Page 69

    Sp-5000m-ge2 / sp-5000c-ge2 - 67 - table23. Trigger source 7.3.4 trigger activation this command can select how to activate the trigger. Rising edge: at the rising edge of the pulse, the trigger is activated. Falling edge: at the falling edge of the pulse, the trigger is activated. Note: when trigge...

  • Page 70

    Sp-5000m-ge2 / sp-5000c-ge2 - 68 - 7.4. Normal continuous operation (timed exposure mode/trigger mode off) this is used for applications which do not require triggering. In this mode, the video signal for the auto-iris lens is available if aux connector is configured with option type 2. For the vide...

  • Page 71

    Sp-5000m-ge2 / sp-5000c-ge2 - 69 - 7.5.2 if the overlap setting is “readout” trigger ccd exposure xeen fval exposure active exposure period t5 t1 t2 t3 t4 fig.35 readout 7.6. Trigger width mode in this mode, the exposure time is equal to the trigger pulse width. Accordingly, longer exposure times ar...

  • Page 72

    Sp-5000m-ge2 / sp-5000c-ge2 - 70 - 7.6.2 if the overlap setting is “readout” trigger ccd exposure xeen fval exposure active exposure period t6 t1 t2 t3 t4 t5 fig.37 readout note: timing at the end of the trigger if the trigger overlap is set to readout as for the timing for the end of the exposure b...

  • Page 73

    Sp-5000m-ge2 / sp-5000c-ge2 - 71 - 7.7. Rct mode until the trigger is input, the camera operates continuously and the video signal for the auto-iris lens is output, provided the aux connector has been ordered with a type 2 configuration option. At this moment, the video signal, fval and lval are out...

  • Page 74

    Sp-5000m-ge2 / sp-5000c-ge2 - 72 - 7.8. Piv (particle image velocimetry) the particle image velocimetry mode can be used in applications where 2 images need to be taken with a very short time interval. It can only be used with strobe flash as illumination. The first accumulation time is 10 sec to 2 ...

  • Page 75

    Sp-5000m-ge2 / sp-5000c-ge2 - 73 - 7.9. Sequence roi trigger this mode allows the user to define a preset sequence of up to 10 images, each with its own roi, exposure time and gain values. Primary settings to use this mode exposure mode: timed trigger mode: on video send mode: trigger sequence or co...

  • Page 76

    Sp-5000m-ge2 / sp-5000c-ge2 - 74 - 7.9.2 trigger sequence mode basic timing in this mode, as each trigger input is received, the image data associated with the next index within the preset sequence is output. Index 0 index 1 index 2 index 3 index 4 frame start trigger in sequence behavior frame coun...

  • Page 77

    Sp-5000m-ge2 / sp-5000c-ge2 - 75 - set offset x of sequence roi. Sequence roi binning horizontal = 1 (off): setting range is 0 to (2544 - [sequence roi width]) for monochrome setting range is 0 to (2552 - [sequence roi width]) for color sequence roi binning horizontal = 2 (on): setting range is 0 to...

  • Page 78

    Sp-5000m-ge2 / sp-5000c-ge2 - 76 - (14) sequence roi reset command this command resets the current index pointer and reverts to index 0 in the table. Frame count is also re-initialized. 7.10 multi roi function this function divides one frame image into a maximum of 5 images vertically and reads out ...

  • Page 79

    Sp-5000m-ge2 / sp-5000c-ge2 - 77 - 7.10.1 multi roi setting parameters (1) multi roi index max：setting value = 0 ～ 4 maximum 5 roi settings are possible in a frame. Set index 0 through 4 in multi roi index table as an application requires. (2) multi roi width multi roi width can be set individually ...

  • Page 80

    Sp-5000m-ge2 / sp-5000c-ge2 - 78 - 7.11. Operation and function matrix table27. Operation and function matrix exposure operation trigger mode trigger option v-binning note1 h-binning note1 exposu re time roi awb note2 auto iris output auto gain auto exposur e trigger over lap video send mode hdr not...

  • Page 81

    Sp-5000m-ge2 / sp-5000c-ge2 - 79 - 8. Other functions 8.1 black level control this function adjusts the setup level. The adjusting level is -64 to +63lsb at 10-bit output. 8.1.1 black level selector the following factors can be set. Sp-5000m-ge2: digitalall sp-5000c-ge2: digitalall/digitalred/ digit...

  • Page 82

    Sp-5000m-ge2 / sp-5000c-ge2 - 80 - x16 x1 16 1 gain amplitude gain setting value gain control range for monochrome 24db 0db the master gain control uses digital gain control. All digital gain can be set by x0.01/step. If the digital gain is set too high, a break in the histogram may occur. The above...

  • Page 83

    Sp-5000m-ge2 / sp-5000c-ge2 - 81 - gain auto max: the maximum value of gainauto control range can be set gain auto min: the minimum value of gainauto control range can be set alc reference: the reference level of gain auto control can be set (common with exposureauto) alc area type： the area for exp...

  • Page 84

    Sp-5000m-ge2 / sp-5000c-ge2 - 82 - 8.3.2 lut index this represents the “starting” or “input” pixel value to be modified by the lookup table. The sp-5000-ge2 has a 256-point lookup table, meaning the index points are treated like an 8-bit image with 0 representing a full black pixel and 255 represent...

  • Page 85

    Sp-5000m-ge2 / sp-5000c-ge2 - 83 - dark compression 0: dark compression 1: linear (default) dark compression function linear(factory default) no compression, gamma=1.0 dark compression compress the signal level in the dark portion. It can improve the signal to noise ratio, but on the other hand, the...

  • Page 86

    Sp-5000m-ge2 / sp-5000c-ge2 - 84 - note: under the following conditions, the shading correction circuit may not work properly.  if there is some area in the image with a video level less than 70%  if part of the image or the entire image is saturated  if the highest video level in the image is le...

  • Page 87

    Sp-5000m-ge2 / sp-5000c-ge2 - 85 - the raw data contains only luminance information for each color and outputs as a monochrome signal. The bayer color interpolation function can complement lacking color information on each pixel and output rgb or yuv color data as the result. Color interpolation com...

  • Page 88

    Sp-5000m-ge2 / sp-5000c-ge2 - 86 - 8.8.2 setting for p-iris lens being used p-iris lenses use an absolute setting value control system and therefore, if the following parameters are input, precise iris position control is possible. 8.8.2.1 p-iris lens select select the lens used from the p-iris sele...

  • Page 89

    Sp-5000m-ge2 / sp-5000c-ge2 - 87 - 8.8.3.2 zoom wide: while this command is supplied, the zoom will continue to move towards wide angle. Tele: while this command is supplied, the zoom will continue to move towards telephoto. Stop: when this command is supplied, the zoom operation stops. 8.8.3.3 focu...

  • Page 90

    Sp-5000m-ge2 / sp-5000c-ge2 - 88 - 8.10 hdr (high dynamic range) (sp-5000m-ge2 only) hdr sensing mode can be set when hdr mode is set to on while exposure mode is timed. The parameters to configure dynamic range are hdr_slope level 1, level 2, level 3 and level 4. The user can select any one of thos...

  • Page 91

    Sp-5000m-ge2 / sp-5000c-ge2 - 89 - 9. Camera setting 9.1 camera control tool in the sp-5000m-ge2 and sp-5000c-ge2, control of all camera functions is done by the jai sdk and control tool software. All controllable camera functions are stored in an xml file inside of the camera. The jai sdk and contr...

  • Page 92

    Sp-5000m-ge2 / sp-5000c-ge2 - 90 - 10. External appearance and dimensions dimensions tolerance: ± 0.3mm unit: mm fig.56 outside dimensions.

  • Page 93

    Sp-5000m-ge2 / sp-5000c-ge2 - 91 - 11. Specifications 11.1 spectral response fig.57 spectral response (sp-5000m-ge2) fig.58 spectral response (sp-5000c-ge2) (with ir cut filter) note: full sensor response. Ir-cut filter not shown..

  • Page 94

    Sp-5000m-ge2 / sp-5000c-ge2 - 92 - 11.2 specifications table specifications sp-5000m-ge2 sp-5000c-ge2 scanning system progressive scan, 1-tap synchronization internal interface 1000base-t ethernet (gige vision 2.0) x 2ports (100base-t can be used) complies with single, slag (static link aggregation)...

  • Page 95

    Sp-5000m-ge2 / sp-5000c-ge2 - 93 - acquisition frame rate 44 fps (max) ～ 0.125 fps (min), at 8-bit output trigger selector acquisition acquisition start/ acquisition stop exposure frame start transfer acquisition start/ acquisition stop / frame transfer exposure mode off, continuous, timed (eps), tr...

  • Page 96

    Sp-5000m-ge2 / sp-5000c-ge2 - 94 - operating temperature/humidity performance guaranteed -10 c to +50 c / 20 – 80% (no-condensing) operating temperature / humidity -45 c to +70 c/20% to 80% (no-condensing) storage temp. / humidity -45 c to +70 c/20% to 80 % (no-condensing) regulation ce (en61000-6-2...

  • Page 97

    Sp-5000m-ge2 / sp-5000c-ge2 - 95 - appendix 1. Precautions personnel not trained in dealing with similar electronic devices should not service this camera. The camera contains components sensitive to electrostatic discharge. The handling of these devices should follow the requirements of electrostat...

  • Page 98

    Sp-5000m-ge2 / sp-5000c-ge2 - 96 - 4. Caution when mounting the camera when you mount the camera on your system, please make sure to use screws of the recommended length described in the following drawing. Longer screws may cause serious damage to the pcb inside the camera. If you mount the tripod m...

  • Page 99

    Sp-5000m-ge2 / sp-5000c-ge2 - 97 - manual change history date revision changes april 2014 preliminary new release july 2014 1.0 new release aug. 2014 1.1 revise lag settings information sept. 201 1.2 revise spectral response oct. 2014 1.3 revised b/w spectral response with wider wave length, add the...

  • Page 100

    Sp-5000m-ge2 / sp-5000c-ge2 - 98 - user's record camera type: sp-5000m-ge2 / sp-5000c-ge2 revision: …………….. Serial no. …………….. Firmware version. …………….. For camera revision history, please contact your local jai distributor. User's mode settings. User's modifications. Company and product names menti...