Instruction read these instructions carefully before use. Please keep these instruction after assembling. Bd-5 ord. No. 00 6136 gb safety precautions this radio control model is not a toy! Not suitable for persons under 14 years! * first-time builders should seek advice people having building experi...
2 sicherheitshinweise contents safety information 2 general information 2 technical data 2 highlights 2 box contents 3 building the model 3 - 17 control throws and centre of gravity 17 recommended accessories 18 plans 19 - 21 safety information flying models are not toys, and should only be operated...
3 kit contents: • cnc laser cut formers and ribs, strip wood, selected light weight balsa sheet and aircraft grade plywood. • fitting kit including wheels, undercarriage, horns and hinges. • clear canopy. • instructions. 1. Glue the rings on the holes 3. Glue the battery support in a right angle to ...
4 5. Apply the side piece and glue. The front piece is later taken off to make room for the battery 6. Glue the wing screws support 7. Both wing supports are glued and leave to dry. 9. First of all, only glue the side pieces to the front and leave to dry. 8. Rear and front fuselage pieces are put to...
5 11. Fuselage, upper part: use 3 mm ply on the left and right side and it is lapping over. The fin is later fitted in the gap. 12. Straighten the fuselage borders and glue to the grooves. The front lower fuselage is covered with 2 mm balsa and sanded the edges to the sides around 13. Glue both 1.5 ...
6 17. Start assembly from the middle and move to the right/ left from there. 18. The layers should overlap each other. 19. The fuselage nose sanded. 21. Use a wet cloth and glue glue to the top in the middle. 20. Now the rear fuselage piece is covered. Use a sheet of balsa and glue to the bottom edg...
7 23. Fuselage cover on the underside of the cockpit. 24. Rudder 25. Elevator 27. A) push the elevator right into the „v“. B) insert the ply-rings from the top, turn and glue to fuselage side. C) the vertical fin should be able to be moved up and down but not to the back. 26. As a pivot, a 4 mm alum...
8 29. Ready assembled pivot-system 30. You can use a pole as shown for the controls. For example: made of 2x3mm balsa (hard) with spring wire in-between. The linkage to the elevator has to be stable once tension is applied and should not deform. 31. Zero clearance fitted linkage. 33. Glue ply braces...
9 35. Further ribs are applied to the wing spar in order r9. The last rib is glued and the others aligned. 36. The servo bay is glued to the underside 37. The first rib is now glued after a 1,5 mm is put under it. This will help to keep them ribs aligned. 39. The lower cover is cut out. 38. The smal...
10 41. The aileron border is slided in the grooves and glued. 42. The aileron is later taken from the two ribs 43. The tip is now glued together made from 2 x 6 mm balsa. 45. For the wing screws underline the back border approx 25 mm. 44. The wing parts are now covered in the inner/ lower part. 46. ...
11 47. Sanded 48. The edges are sanded 49. The connection rod is made of 2x 1,5 mm ply which is also used on the plane. Slot it in once ready. 51. Example for assembly of the servo hatch cover. 50. Glue both parts of the wings together. 52. After the edges between ribs and border are reinforced with...
12 53. Overlying rib material can now be sanded. 54. So the covering foil does not crease in the region of the aileron, a “frame” is build for the rudder horn made of 1,5 mm balsa. Once the covering is done, the pocket can be cut out and the rudder horn glued into place. 55. The ailerons can be rein...
13 set-up: aileron +/- 10 - 15 mm deflection elevator +/- 10 - 15 mm deflection manual start: with ~ 70% elevator pulled (for example, program as flight phase) cg: 37 - 39 mm from the nose downthrust ~ 5-7 ° up (installed 5°, according to engine and propeller with washer to alter) engine course ~ 0°...
14 plane - the original sized plan can be found on the dvd 37.
15.
All rights reserved. Copyright jamara e.K. 2011 copying or reproduction in whole or part, only with the expressed permission of jamara e.K. Jamara e.K. Inh. Erich natterer am lauerbühl 5 - de-88317 aichstetten tel. +49 (0) 75 65/94 12-0 - fax +49 (0) 75 65/94 12-23 info@jamara.Com www.Jamara.Com ord...
