1. DL manuals
  2. Jamara
  3. Toy
  4. Gee Bee Z 00 6131
  5. Instructions Manual

Jamara Gee Bee Z 00 6131 Instructions Manual

Summary of Gee Bee Z 00 6131

  • Page 1

    Instructions please read these instructions carefully before starting to build the model and retain them afterwards for future reference! Gee bee z part.-no. 00 6131 gb safety instructions this model is not a toy! Not suitable for under 14 year olds! * beginners should seek the help of an experience...

  • Page 2: Contents

    2 contents safety information general information technical specifications safety information 2 general information 2 technical specifications 2 kit contents 3 building the kit 3-9 control throws and c of g 9 recommended accessories 9 building plans 10-12 wingspan approx. 800 mm length approx. 750 m...

  • Page 3: Kit  Contents

    3 kit contents • cnc laser cut formers and ribs, strip and sheet from selected light weight balsa and ply • fitting kit, including wheels, undercarriage, horns and hinges etc. • clear canopy • instructions building the model assemble 2 fuselage halves as shown ensuring that you build a left and a ri...

  • Page 4: Building The Model

    Glue the 4 front fuselage rings on and sand the edges down. Glue the stringers into the slots, the stringers will protrude approx. 1.5mm out of the of the side formers. 4 building the model elevator cut out glue the fin into place ensuring that it is vertical and square along the fuselage..

  • Page 5: Building The Model

    5 building the model build the battery cover and use 1.5 mm sheet to plank it. Mount the rudder as shown here but do not glue the hinges yet. Use 1.5 mm sheet to plank the upper fuselage over the 3 mm stingers only as shown here..

  • Page 6: Building The Model

    6 building the model assemble the elevator and fit it temporarily to the fuselage. Adjust the fit until the elevator is horizontal. Sand all of the edges round. Assemble 2 cowl rings as shown here. The front ring is a made of 3 laminations. Glue the horizontal spacer plates into position. Use sheet ...

  • Page 7: Building The Model

    Building the model glue on the 4th and last ring which is 6 mm thick on and sand the edges off. Glue the undercarriage strengtheners between the ribs as shown. The cowl is glued to the fuselage after covering..

  • Page 8: Building The Model

    Once the lower sheeting has been fitted, build the lower wing fair- ing and use 1.5mm sheet to plank it. 8 building the model glue 6 laminations together to make the wheel pants. Cut a channel into the front and rear of the undercarriage fairings to allow the undercarriage leg wires to be let-in. Us...

  • Page 9: Zusammenbau

    9 zusammenbau control throws and c of g: recommended accessories elevator: +/- 15 mm rudder: +/- 30 mm aileron: +/- 12-15 mm centre of gravity: 53 mm behind the leading edge this shows how the wheel pants are glued to the undercarriage wire and the wing. Motor a2820/6 part no. 132820 battery pack li...

  • Page 10: Building Plan -

    10 building plan - the original sized plan can be found on the dvd wings.

  • Page 11: Bauzeichnung -

    Bauzeichnung - die originalgrösse finden sie auf der beiliegenden dvd 11 fuselage side.

  • Page 12: Newsletter

    All right reserved copyright jamara e.K. 2009 reproduction in part or whole only with the expressed permission of jamara e. K. Jamara e.K. Inh. Erich natterer am lauerbühl 5 - de-88317 aichstetten tel. +49 (0) 75 65/94 12-0 - fax +49 (0) 75 65/94 12-23 info@jamara.De www.Jamara.De top view aktuelle ...