Summary of Starlet 006140
Page 1
Gb instruction ord. No. 00 6140 starlet it‘s not a toy!.
Page 3
3 general information as the company jamara e. K. Has no influence over the use, main - tenance or conditions under which our products will operate, we accept no responsibility for any damage caused be it of a physical, financial or theoretical nature. Jamara e. K. Will accept no claim against it wh...
Page 4
4 7. The motor support already has a side pull and drop installed. Looking from the cockpit the motor rib is showing to the right. 8. The fuselage rib and fuselage belts are glued. 5. Insert further ribs and glue together. !!Adhere to right angle and make sure nothing is displaced!! 6. The construct...
Page 5
5 13. The baldachin support is mounted from the shown parts. 14. The slat for wire guidance is glued into place 11. The frame for the battery cover are assembled as shown. For it to fit nicely we recommend to glue it later on once the fuselage is completed. 12. The half-rib is now glued to the fusel...
Page 6
6 19. The fuselage top is planked with 1.5 mm at the front. 21. 4 mm balsa sanded. 20. The fuselage back is planked with 1.5 mm balsa and at the top it is rounded with 4 mm balsa leftovers. 22. The battery cover planked and sanded. 17. Plank fuselage with 1.5 mm balsa… 18. … underside with 2 mm bals...
Page 7
7 25. The balsa pieces are sanded incl. The empennage dummy. If successful the rear of the fuselage will look as shown once the dummy has been pulled out. 27. The empennage and rudder. The wire will be used to joint the elevator. 26. The empennage can be fitted to check. You may have to adjust for t...
Page 8
8 31. … and later fixed with a plywood piece. 33. To achive more glue surface, rests from inside can be glued to the edge. 32. The cowling is made of two halfs which are later glued together. 34. Once both pieces are glued together, the fuselage is sanded wet with 400 – 600 sanding paper. 29. The su...
Page 9
9 37. Sanded pants. 40. The plywood holm is glued to the plank along the edge. 38. The rudder is sanded on one side if foil is used as hindge and on both sides if a hindge is used. 41. The holm is fitted with ribs and the rear holm is inserted. The shorted holm is not glued yet. 35. The undercarriag...
Page 10
10 43. The aileron ledge is glued. 45. In this pocket small alu angle brackets are glued into place. 44. Small pockets are made of playwood for joining the wings later on. 46. Now the front third can also be planked. 41. Now everything is fixed by glueing all parts together. You can also use the pla...
Page 11
11 49. One left and right wheel arch is glued together. 51. Trailing edge and ribs are supported with small balsa triangles. 50. Wheel arches are glued and the leading edge is also glued. 52. Upper planking of wings with the leading edge 47. The servo frame is glued together. 48. And the cover scrue...
Page 12
12 55. Sand edge once finished. 57 clamps and alu angles are glued at first. Later they can be removed with the playwood fitting. 56. The wing is now fitted and the baldachin is aligned. 58. The alu angles are used in the wings 8 times. Cut approx 20 mm of alu off, drill through and bend. 53. Both w...
Page 13
13 61. Servo mounting. Set-up aileron: +/- 10 mm ausschlag elevator: +/- 10 mm deflexion side rudder: +/- 25 mm deflexion centre of gravity: 46mm from the nose down thrust: ~ 2° nach down traction: ~ 2 - 2,5° right (depending on motor and prop) 62. Finished model 59. Also for the outer braces alu an...
Page 14
14 recommended accessories no.13 2217 motor a2217/8-bi no.14 1368 battery lipostar turbo 1800mah 3n no.17 4412 4 x servos xt-9 no.08 1925 controller xetronic 25a no.34 0056 propeller apc elektro 9 x 6 no.17 7312 tail skid wheel steerable 25 mm complete.
Page 15
15 plane - the original sized plan can be found on the dvd starlet.
Page 16
16 plane - the original sized plan can be found on the dvd module starlet.
Page 17
17 plane - the original sized plan can be found on the dvd 1° ewd cg module starlet 1sv.
Page 18
18 plane - the original sized plan can be found on the dvd 97,50 71 17,50 97,50 4 152 49 30 97,50 78 135° 4 x 2 x undercarriage.
Page 19
19 plane - the original sized plan can be found on the dvd 331 345 brace.
Page 20: Coupon
All rights reserved. Copyright jamara e.K. 2012 copying or reproduction in whole or part, only with the expressed permission of jamara e.K. Jamara e.K. Inh. Erich natterer am lauerbühl 5 - de-88317 aichstetten tel. +49 (0) 75 65/94 12-0 - fax +49 (0) 75 65/94 12-23 info@jamara.Com www.Jamara.Com ord...