Summary of CRT.5
Page 1
Rev. 5-16-07.
Page 2
Important-read this before running running nitro kit is fun and easy, but to make this a safe and good experience you must observe a few rules. This kit is extremely fast, easily over 65kph, and can seriously injure someone if you are not careful. Any running area you choose must be dry. Do not run ...
Page 3
Things need besides the kit radio control unit glow plug long heat with battery & charger # 10215....$27.95 (please note ofna glow heats available) note: pro kit does not include engine! Glow fuel 20% required for operation bottle’s with spout # 10160 - large 500cc # 10161 - large 500 ccauto stop # ...
Page 4
Plastic parts for use 40833 receiver box 40834 servo saver 40839 front c hub 40835 diff. Case 40836 front and rear lower arm 40837 front upper arm and arm holder 40840 front and rear gear box.
Page 5
30802 throttle linkage plastic plastic parts for use symbol used throughout the instruction manual ensure free movement ensure free movement apply grease apply grease oil tighten tighten do not over tighten rotate direction rotate direction contact adhesive contact adhesive sc e rw ceme t n bag 1:1 ...
Page 6
1 2 3 assembly of the center diff. Assembly of the front gear case assembly of the front shock stay step 1 step 2 step 1 step 2 step 1 step 2 .....X8 30779 4x10mm washer 30773 4mm cross pin .....X2 dif . Oil f 40011 2.6x10mm 30773 40805 30779 .....X4 tight the diff screws in this order. 1 4 3 2 3x35...
Page 7
4 5 6 assembly of the front lower arms assembly of the front upper arms assembly of the knuckle arms assembly for both right and left side. Step 3 step 1 step 2 step 4 step 2 3x8mm 3x8mm 3x12mm 40813 40837 40825 40837 40837 40837 3x12mm 40837 40824 40841 40818 37360 40818 40840 37390 37430 37430 408...
Page 8
7 8 9 assembly of the front suspension arms assembly for both right and left side. Assembly of the front stabilizer assembly for both right and left side. Makes two rods for left and right hand-side. Assembly of the front stabilizer 3x4mm 3x15mm 40823 3x15mm 3x8mm 40848 40848 30341 30403 2.5x8mm 3x3...
Page 9
10 11 12 assembly of the servo saver assembly of the servo saver and the steering tie-rod *approx. 0.5mm step 1 step 2 step 2 *approx. 37.5mm 1:1 step 1 step 2 assembly of the servo saver onto the front gear box 37360 37360 37360 40834 40834 40811 40810 40809 40834 37220 3x8mm 37220 3x8mm 40834 4081...
Page 10
13 14 15 assembly of the rear gear case assembly of the rear shock stay assembly of the wing stay step 1 step 2 step 1 step 2 3x10mm 3x12mm 38254 38254 40804 37430 40840 37430 40806 4x4mm 3x35mm 3x35mm 40815 3x10mm 40840 40834 3x10mm 40842 3x10mm 40873 3x10mm 40842 40842 40842 40842 40842 40842 3x10...
Page 11
16 17 18 assembly of the wing stay assembly of the rear lower arms assembly of the rear suspension arms step 1 step 2 assembly for both right and left side. 3x12mm 40834 3x15mm 3x12mm 3x12mm 40816 40837 40825 40836 40837 40836 3x8mm 3x8mm 3x4mm 40823 37430 37430 40843 40840 37390 40875 40843 94004 3...
Page 12
19 20 21 assembly of the rear suspension arms assembly for both right and left side. *approx. 48mm 1:1 assembly of the rear stabilizer makes two rods for left and right hand-side. 3x15mm assembly of the rear stabilizer 30403 40828 37100 37100 3mm 3x15mm 3x15mm 30341 30403 3x8mm 40848 40848 40817 2.5...
Page 13
222 24 assembly of the center diff. Mount assembly of the front gear case onto chassis 23 assembly of the brake disk into center diff. Step 1 step 3 step 2 step 1 * remove the double-side tape before assembly. Double-side tape 40844 40844 40844 30171 40830 40830 3x3mm 3x10mm 39243 39243 30171 3x3mm ...
Page 14
25 26 27 assembly of the center diff. Onto chassis assembly of the rear gear case onto chassis suitable servo (check your servo before use.) 40822 3x10mm 3x10mm 40822 3x10mm 3x10mm 3x10mm 94019 3x10mm flat head hex screw .....X6 94019 3x10mm flat head hex screw .....X4 type a type b 28~32mm 35~36mm ...
Page 15
28 29 assembly of the radio tray assembly of the radio tray and receiver box step 1 step 2 step 1 step 2 step 1 step 2 3x8mm 3x8mm 3x5mm 40874 40833 40833 3x8mm 3x8mm 3x8mm 3x8mm 3x5mm 3x8mm 3x5mm 3x8mm 3x8mm 3x10mm 3x8mm 10281 3x8mm 40833 40833 40833 40833 40833 94002 3x8mm hex screw .....X10 94018...
Page 16
30 31 32 assembly of the radio tray and receiver box assembly of the radio tray onto chassis assembly of the steering servo and steering rod 37410 40855 30560 3x10mm 3x10mm 30661 37360 38398 37650 37650 40833 94019 3x10mm flat head hex screw .....X5 use the screw provided with your servo. Receiver 4...
Page 17
33 34 35 assembly of the fuel tank onto chassis ²Õ¦xªo½c¦Ü©³½l assembly of the clutch assembly of the clutch and engine mount step 1 step 2 step 1 step 2 3x10mm *put the p3 o-ring under the fuel tank before assembly. Tm-47 37070 10098 40814 10330 10010 10102 10399 34110 34110 3x8mm 3x5mm 5x8x0.3mm 5...
Page 18
36 37 38 assembly of the engine onto chassis assembly of the manifold and muffler assembly of the throttle linkage 14 step 1 step 2 step 1 step 2 step 3 cut off the servo saver as shown. 2mm 30661 2x8mm 30802 3x10mm 2.6x18mm 30802 30802 30531 3x3mm 10300 30802 30172 10300 40829 40829 37100 37100 (1m...
Page 19
39 40 41 assembly of the throttle linkages into lever adjusting the engine control linkages assembly of the air filter step 1 step 2 40858 40856 40857 40856 3x8mm 10185 3x3mm 10300 10300 approx. 1mm gap (neutral) (throttle high) (brake) idling adjusting screw . 10300 approx. 0.5mm carburetor is open...
Page 20
42 43 assembly of the front shocks assembly of the rear shocks step 1 step 2 step 3 step 4 fit the o-ring into groove before assembly. Fill the shocks with oil. 1 8 m m correct shock assembly carefully screw the shock shaft into the bottom of the plastic ball and until the distance between the ball ...
Page 21
44 45 46 assembly of the front shock absorber assembly of the rear shock absorber assembly of the front bumper step 1 step 3 assembly for both right and left side. Assembly for both right and left side. Step 2 3mm nylon nut 3x8mm 3x15mm 3x8mm 3mm nylon nut 3x15mm 3x10mm 3x10mm 3x10mm 3x12mm 40842 40...
Page 22
47 48 49 assembly of the fuel tube assembly of the wing assembly of the tires and wheels connect to carbulater. Connect to fuel nipple. Connect to fuel tank nipple. Connect to pressure nipple. Step 1 step 3 step 2 in s t a n t g u e l apply instant glue into the groove of the wheel. 10177 10177 4084...
Page 23
50 assembly of the tire onto front knuckle and rear hub assembly for both right and left side. Tire and wheel assembly. 51 cut out the body as shown. Use a neutral detergent to remove any dirt and oil. Mask the windows from the inside with masking tape. Paint the body with polycarbonate spray paints...
Page 24
52 mounting body starter box (not included) 1.2v 53 starting of the engine 1. Turn on transmitter and then receiver. 2. Fill fuel tank with fuel bottle. 3. Connect 1.2v glow plug starter. 4. Start engine with 12v starter. ( note the direction of the starter.) 5. After the engine be started, remove t...
Page 25
Your radio control model can move at high speed and therefore can cause injury to people or damage property. It is your responsibility to operate your model safely. For engine use, refer to the manual included with the engine. To prime the engine with fuel, press down the primer button. Attach one c...
Page 26
.12 only.
Page 27
Jammin mini crt.5 set-up sheet date:________________ driver:_________________ front suspension rear suspension shock spring: __________________ shock spring: _______________________ shock piston: shock piston: shock oil wt: __________0__________ shock oil wt: ________ shock length:________ (center t...
Page 28
Blank.
Page 29
Jammin mini crt.5 set-up sheet date:________________ driver:_________________ front suspension rear suspension shock spring: __________________ shock spring: _______________________ shock piston: shock piston: shock oil wt: __________0__________ shock oil wt: ________ shock length:________ (center t...
Page 30
Blank.
Page 31
Jammin mini crt.5 set-up sheet date:________________ driver:_________________ front suspension rear suspension shock spring: __________________ shock spring: _______________________ shock piston: shock piston: shock oil wt: __________0__________ shock oil wt: ________ shock length:________ (center t...
Page 32
Blank.
Page 33
Part # description retail part # description retail 10009 clutch shoes, red, 3 shoes 13.95 40817 sw ay bar 2.Om m fr/rr crt.5 4.95 10098 clutch nut, sg shaft 4.95 40818 king pin screw crt.5 2.95 10102 springs, clutch, black 3 pcs. 4.95 40822 center drive shaft 44/82.5mm 14.95 10120 spring, manifold,...
Page 34
Blank.
Page 35
30774 alu m . D iff c r o ss pin h c 6pc s. 9.95 38457 pad , br ake, c ar bo n & st eel pad 31.95 40591 br ake d isk, fiber x 1-c r /c r t 14.95 40872 c n c 7075 fr o n t sh o c k t o w er 25.95 40873 c n c 7075 r ear sh o c k t o w er 27.95 40874 g r aph it e r ad io t r ay c r t .5 29.95 40875 u n...
Page 36
Blank.
Page 37
Racer’s name tel:( ) address city state zip dealer’s name tel: ( ) address city state zip ofna racing congratulates you on your purchase of our fine ofna product. With proper maintenance and han- dling this kit will provide many hours of enjoyment. The registration card should be filled out and mail...