Jands 4Pak-D User Manual - Scene Operation

Page of 8

Download

Print this page

Bookmark us

JANDS 4Pak-D

- 6 -

User Guide

To record and playback a User Chase sequence:

User chase sequences are fully programmable up to 32 steps long.

Press the Display Mode button if necessary to put the Display into Prog (Chase)

mode.

Ensure the Chase is not active ie the Go/Load LED is not illuminated.

Using the [+] or [-] buttons choose a chase sequence from U 1 to U 9.

Press the Enter button to start recording the selected chase.

Adjust the channel levels as necessary for the step.

Press the Enter button to record the levels.

Repeat steps 5 and 6 until all steps have been recorded.

Note that any step may be re-recorded if necessary by using the + and - buttons to select the

step, adjusting the levels as required, and pressing Enter to record. To view the step levels,

press and hold the Chase button while the step number is displayed. Release the Chase button

to continue.

Press the Exit button to get out of chase record mode.

To activate the chase, press the Go/Load button.

It is possible to delete all steps from a point onward for example, steps 5 and 6 of a 6 step

chase. To delete all steps from step 5 onward Enter Chase record mode, select the first setp to

be cut, then press and hold store for 3 seconds. The 4Pak-D flashes CUT and pressing Enter

again confirms the deletion.

To delete the entire chase, press Cancel and Enter together while the chase number is

displayed. The 4Pak-D flashes CFR and pressing Enter again confirms the deletion.

Scene Operation

A Scene allows the operator to assign pre-recorded dimmer levels for all channels to a single

channel fader. There are a total of four pages each containing 5 scenes.

To record and playback a Scene:

Press the Display Mode button if necessary to put the Display into Prog (Chase)

mode.

Ensure the Chase is not active ie the Go/Load LED is not illuminated.

Using the [+] or [-] buttons choose a Scene page from S 1 to S 4.

Press the Enter button to start editing the selected scene page.

Adjust the channel levels as necessary for the scene.

Press the Enter button to record the levels.

Repeat steps 5 and 6 until all 5 scenes have been recorded. The display will

show FUL when all 5 scenes on the page have been programmed.

Note that any scene may be re-recorded if necessary by using the [+] and [-] buttons to select

the scene, adjusting the levels as required, and pressing Enter to record them.

Press the Exit button to leave scene record mode.

To activate the scenes, press the Go/Load button. The channel faders and flash buttons are

now used to control scenes 1 through 4, while the rate fader is used to control scene 5.

To delete the Scene page, press Cancel and Enter together while the Scene page number is

displayed. The 4Pak-D flashes CFR and pressing Enter again confirms the deletion.

« ‹ Prev 2 3 4 5 6 7 8 Next › »

Summary of 4Pak-D

Page 1
Supplied by:.
Page 2: Copyright & Disclaimer
Jands 4pak-d - 2 - user guide copyright & disclaimer this product is approved for use in europe and australia/new zealand and conforms to the following standards: en61000-6-1 en55015:2000 en60065 conformance has been achieved for intended usage in environment e1: residential. To ensure continued com...
Page 3: Introduction
Jands 4pak-d - 3 - user guide introduction the 4pak-d is a four channel integrated desk/dimmer unit with extensive chase and scene facilities plus the ability to be driven from an external dmx-512 source. It has been designed for applications where portability and ease of operation are prime conside...
Page 4: Layout
Jands 4pak-d - 4 - user guide layout 1. Channel output sockets: the four output sockets connect to the lights. 2. Overload circuit breaker: the circuit breaker protects the 4pak-d from faults and overloading. 3. Channel faders: these faders control the channel output levels. In scene mode these fade...
Page 5: Operation
Jands 4pak-d - 5 - user guide operation general rules the operation of the 4pak-d is defined by a few simple rules: the mimic led in the channel flash button always shows the channel level. The master fader always scales the level of the faders and the chaser output. The channel flash buttons always...
Page 6: Scene Operation
Jands 4pak-d - 6 - user guide to record and playback a user chase sequence: user chase sequences are fully programmable up to 32 steps long. 1. Press the display mode button if necessary to put the display into prog (chase) mode. 2. Ensure the chase is not active ie the go/load led is not illuminate...
Page 7: Dmx Operation
Jands 4pak-d - 7 - user guide dmx operation the 4pak-d dimmer channels can operate under the control of an external dmx source, such as a lighting control console. Plug a dmx cable into the input socket on the backpanel of the 4pak-d and connect the other end of the cable to a dmx source. To set the...
Page 8: Display Glossary
Jands 4pak-d - 8 - user guide display glossary c 1 indicates the 4pak-d will run factory programmed chase #1 when the go/load button is pressed. U 2 indicates the 4pak-d will run user programmed chase #2 when the go/load button is pressed. S 4 indicates the 4pak-d will run user programmed scene page...