Jandy RS-P4 Installation data - page 23
Page 23
4.2.
Restarting the System (Clear Memory)
Menu
To remove all labeling, programming, assignments
and temperature settings, highlight MENU and
press SELECT. Highlight SYSTEM SETUP
and press SELECT (see Figure 30). Highlight
CLEAR MEMORY and press SELECT. Highlight
CONTINUE and press SELECT. Use the UP or
DOWN button to highlight YES or NO and press
SELECT. There will be about a 15 second delay
before you see the FINISHED screen. Highlight
CONTINUE and press SELECT to return to the
SYS TEM SETUP.
CAUTION
In service mode, the safety interlocks for
equipment protection are overridden.
Óß×Ò ÓÛÒË
ØÛÔÐ
ÐÎÑÙÎßÓ
ÍÛÌ ÌÛÓÐ
ÍÛÌ Ì×ÓÛ
ÐÜß ÑÐÌ×ÑÒÍ
ÍÇÍÌÛÓ ÍÛÌËÐ
ï
î
-»´»½¬
¾¿½µ
ÐÜß
ÍÇÍÌÛÓ ÍÛÌËÐ
ÍÑÔßÎ ÐÎ×ÑÎ×ÌÇ
ÐËÓÐ ÔÑÝÕÑËÌ
ßÍÍ×ÙÒ ÖÊß-
ÝÑÔÑÎ Ô×ÙØÌÍ
ÍÐß ÍÉ×ÌÝØ
ÍÛÎÊ×ÝÛ ×ÒÚÑ
ÝÔÛßÎ ÓÛÓÑÎÇ
ØÛßÌ ÐËÓÐ
ÓÑÎÛ
ï
î
-»´»½¬
¾¿½µ
ÐÜß
ÝÔÛßÎ ÓÛÓÑÎÇ
ÉßÎÒ×ÒÙ
Ý´»¿®·²¹ ³»³±®§
»®¿-»- ßÔÔ
-¬±®»¼ -»¬¬·²¹-ò
ÝÑÒÌ×ÒËÛ
ï
î
-»´»½¬
¾¿½µ
ÐÜß
ÝÔÛßÎ ÓÛÓÑÎÇ
Ú×ÒßÔ ÉßÎÒ×ÒÙ
ß®» §±« ÍËÎÛ
¬¸¿¬ §±« ©¿²¬ ¬±
ÛÎßÍÛ ßÔÔ
ÍÛÌÌ×ÒÙÍ
áá
ÇÛÍ
ÒÑ
ï
î
-»´»½¬
¾¿½µ
ÐÜß
ÝÔÛßÎ ÓÛÓÑÎÇ
Ú×Ò×ÍØÛÜ
Ю»-- ÍÛÔÛÝÌ
¬± ½±²¬·²«»ò
ÝÑÒÌ×ÒËÛ
ï
î
-»´»½¬
¾¿½µ
ÐÜß
ï
î
-»´»½¬
¾¿½µ
ÐÜß
ÝÔÛßÎ ÓÛÓÑÎÇ
ÛÎßÍ×ÒÙ
ßÔÔ
ÍÛÌÌ×ÒÙÍ
°´»¿-» ©¿·¬
Figure 30. Clear Memory Menu
4.3
PDA System Defaults and General Modes
Default Temperature (Pool/Spa Combination)
Default Pool Temp = 80° F
Default Spa Temp = 102° F
Default Temperature (Pool/Spa Only)
Default TEMP1 = 80° F
Default TEMP2 = 60° F
Default Spa Side Switch Settings
Button 1 = Spa (Filter Pump for pool/spa only models)
Button 2 = Spa Heater (Temp1 pool/spa only models)
Button 3 = AUX1
Button 4 = AUX2
Default Freeze Protection Settings
FILTER PUMP: freeze protection ON. ALL OTHER
EQUIPMENT, freeze protection OFF
NOTE If you select SPA to be freeze protected, water
circulation will switch between pool and spa
every 30 minutes during freezing conditions
once freeze mode is active.
4.3.1 Power Center Service Switch
AUTO Mode (automatic)
1. The PDA Handheld Remote has complete
control of all functions.
2. All programmed settings will operate.
3. All safety delays and equipment protection
in ter locks are operational.
SERVICE Mode
1. The power center has complete control of
all functions.
2. Service mode must be turned on/off at the
power center.
3. No programmed settings will work.
TIMEOUT Mode
1. The power center has complete control for
three (3) hours.
2. After three (3) hours the system will return
to AUTO mode.
3. Programmed on/off times will be
overridden during the three (3) hours.
4. After the three (3) hour "time out", the
system will resume any programmed items
that were overridden.