1. DL manuals
  2. Janome
  3. Sewing Machine
  4. 5812
  5. Instruction Book

Janome 5812 Instruction Book - Danger

Summary of 5812

  • Page 1

    Instruction book.

  • Page 2: Danger

    Important safety instructions this appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsi...

  • Page 3

    1 table of contents section i. Names of parts names of parts ................................................................. 2 standard accessories ....................................................... 3 section ii. Getting ready to sew connecting machine to power supply ...........................

  • Page 4

    2 names of parts q bobbin winder stopper w bobbin winder spindle e spool pin (page 8) r bobbin winding tension disc t thread guide y thread take-up lever u face plate i thread cutter o needle plate !0 extension table (accessory storage) !1 hook cover plate !2 hook cover plate release button !3 threa...

  • Page 5

    3 standard accessories w w w w w q q q q q e e e e e r r r r r t t t t t y y y y y u u u u u i i i i i o o o o o q bobbins w needles e blind stitch foot: g r zipper foot: e t sliding buttonhole foot y spool holder (lrage) u spool holder (small) i seam ripper o screwdriver.

  • Page 6

    4 for your safety * while in operation, always keep your eyes on the sewing area. Do not touch any moving parts such as the thread take-up lever, handwheel or needle. * always turn off the power switch and unplug from the power supply: - when leaving the machine unattended. - when attaching or remov...

  • Page 7

    5 extension table the extension table provides an extended sewing area and can be easily removed for free arm sewing. The accessories can be stored in the table. • detaching the table pull the table away from the machine, as illustrated. • attaching the table push the extension table, inserting the ...

  • Page 8

    6 changing the needle q needle clamp screw w needle clamp e flat side r gap z turn off the power switch. Raise the needle to its highest position by turning the handwheel counterclockwise, toward you, and lowering the presser foot. Loosen the needle clamp screw q by turning it counterclockwise. Remo...

  • Page 9

    7 selecting needle and fabric for general sewing, use needle sizes 11 or 14. A fine thread and needle should be used for sewing lightweight fabrics, so the fabric will not be marred. Heavy fabrics require a needle large enough to pierce the fabric without fraying the needle thread. Use the blue need...

  • Page 10

    8 bobbin winding setting the spool pin insert the spool pin into the hole as shown. Q spool pin w hole setting the spool place a spool of thread on the spool pin with the thread coming off the back of spool as illustrated. A: press the large spool holder q firmly against the spool of thread. Q large...

  • Page 11

    9 n start the machine again. When the bobbin is fully wound, it will stop automatically. Stop the machine and return the bobbin winder spindle to its original position by moving it to the left, and cut the thread with a pair of scissors. Remove the bobbin from the bobbin winder spindle. Winding the ...

  • Page 12

    10 x guide the thread into notch w on the front side of the bobbin holder. Draw the thread to the left, sliding it between the tension spring blades. C continue to draw the thread lightly until the thread slips into notch e. Pull out about 6˝ (15.0 cm) of thread. V attach the hook cover plate. Check...

  • Page 13

    11 threading the machine * raise the thread take-up lever to its highest position by turning the handwheel counterclockwise. * raise the presser foot lifter. * place a spool on the spool pin, with the thread coming off the back of spool (refer to page 18). Z draw the end of the thread around the upp...

  • Page 14

    12 adjust the needle thread tension for a straight stitch • correct tension q needle thread (top thread) w bobbin thread (bottom thread) e to loosen r to tighten the ideal straight stitch has threads locked between two layers of fabric, as illustrated (magnified to show detail). If you look at the t...

  • Page 15

    13 adjust the needle thread tension for a zigzag stitch for an ideal zigzag stitch, the bobbin thread does not show on the right side (top side) of the fabric, and the needle thread shows slightly on the wrong side (bottom side) of the fabric. See the illustrations for the correct appearance. To mat...

  • Page 16

    14 stitch pattern selector dial raise the needle and presser foot. Turn the pattern selec- tor dial to set the symbol corresponding to the desired pattern at the setting mark. Q setting mark stitch length control dial turn the stitch length control dial to set the desired stitch length at the settin...

  • Page 17

    15 section iii. Straight stitch sewing straight stitch machine setting q stitch selector: a or b w stitch length: 1.5 – 4 e needle thread tension: 2 – 6 r presser foot: zigzag foot: a • starting to sew raise the presser foot and position the fabric next to a seam guide line on the needle plate (5/8˝...

  • Page 18

    16 zipper sewing machine setting q stitch selector: w needle thread tension: 2 – 6 e presser foot: zipper foot: e • to snap on the zipper foot q slit w pin e to sew left side r to sew right side fit the pin on the zipper foot into the slit on the foot holder. * to sew the left side of the zipper, at...

  • Page 19

    17 • to sew q 1/8˝ (0.4cm) fabric margin w zipper teeth e zipper tape z attach zipper foot on right-side of pin. Fold back the upper layer seam allowance. Fold back the lower layer seam allowance to leave a 1/8" (0.4 cm) margin of fabric q. Place zipper teeth next to margin edge and pin margin to zi...

  • Page 20

    18 section iv. Zigzag stitch sewing the zigzag stitch is one of the most common and versatile stitches. It can be a utility stitch for button sewing, buttonhole making, hemming, overcasting, mending and darning. It can also be used to decorate with trims, appliques and cut work or as a decorative st...

  • Page 21

    19 button sewing machine setting q stitch selector: b – c w stitch length: any e needle thread tension: 3 – 7 r presser foot: zigzag foot a t feed dog: dropped 1. Drop the feed dogs. Place the button below the zigzag foot, making sure to align the holes with the horizontal slot in the foot. Lower th...

  • Page 22

    20 section v. Utility stitches blind hem stitch machine setting q stitch selector: e or f w stitch length: 2 – 3 e needle thread tension: 2 – 6 r presser foot: blind hem stitch foot: g • to sew t when the needle comes to the left y when the needle comes to the right u guide i folded edge there is a ...

  • Page 23

    21 • to sew z set the pattern selector dial at “ ”. Carefully mark buttonhole length on fabric. Place the fabric under the foot with the buttonhole marking running toward you. Draw both the needle and bobbin thread to the left. Move the slider toward you so that the top mark w on the lider meets the...

  • Page 24

    22 corded buttonhole machine setting q stitch selector: w stitch length: e needle thread tension: 1 – 5 r presser foot: sliding buttonhole foot z with the buttonhole foot raised, hook the filler cord on the spur at the back of the foot. Bring the ends toward you under the foot, clearing the front en...

  • Page 25

    23 satin stitching machine setting q stitch selector: c w stitch length: 0.5 – 1 e needle thread tension: 1 – 4 r presser foot : zigzag foot: a the satin stitch is often used to decorate and to overcast the raw edge on blankets, linens, tablecloths, napkins, etc. It is also attractive in applique. O...

  • Page 26

    24 baste applique pieces on the fabric, or fuse the applique pieces with iron-on fabric joiner. Stitch around the applique making sure the needle falls along the raw edge of the applique. Applique machine setting q stitch selector: b – c w stitch length: 0.5 – 1 e needle thread tension: 1 – 4 r pres...

  • Page 27

    25 lace adds a fanciful, feminine touch to blouses and lingerie. Table linens and pillows become more elegant when trimmed with lace. Fold the raw edge of the fabric at least 5/8˝ (1.5 cm). Place lace underneath and topstitch with blind hem stitch. Trim excess fabric close to stitching. Lace work ma...

  • Page 28

    26 rick-rack stretch machine setting q stitch selector: c w stitch length: s.S. E needle thread tension: 2 – 5 r presser foot: zigzag foot: a section vii. Stretch stitches use it to reinforce areas such as crotch and armhole seams as well as to eliminate puckering on knits and stretch fabrics. Also,...

  • Page 29

    27 serging machine setting q stitch selector: g w stitch length: s.S. E needle thread tension: 3 – 7 r presser foot: zigzag foot a this stitch is ideal for 1/4˝ (0.6 cm) seams on knits or on medium to heavy weight woven fabrics where you want a narrow seam. It is also great for sewing spandex swim w...

  • Page 30

    28 smocking machine setting q stitch selector: d w stitch length: s.S. E needle thread tension: 2 – 6 r presser foot: zigzag foot: a • to sew q wrong side (bottom side) of fabric w knotted edge smocking is a delicate decorative treatment used on children’s clothes or women’s blouses. Choose a soft a...

  • Page 31

    29 section vii. Care of your machine replacing the light bulb note: * unplug the machine. * do not dismantle the machine other than as explained in this section. * do not store the machine in a high-humidity area, near a heat radiator, or in direct sunlight. * clean the outside of the machine with a...

  • Page 32

    30 replacing the bobbin holder z insert the bobbin holder into the hook race. X make sure the knob of the bobbin holder fits next to the stopper on the race. Q knob w stopper c replace the bobbin. Attach the needle plate. Tighten the screw firmly with the screwdriver. E screw caution: do not pull th...

  • Page 33

    31 condition cause reference the needle breaks. Skipped stitches seam puckering the cloth is not fed smoothly. The needle thread breaks. The bobbin thread breaks. 1. The needle thread is not threaded properly. 2. The needle thread tension is too tight. 3. The needle is bent or blunt. 4. The needle i...

  • Page 36

    508-800-122 (en).