DL manuals
Janome
Sewing Machine
HF106
Instructions For Use Manual

Janome HF106 Instructions For Use Manual

Page of 8

Download

Print this page

Bookmark us

IMPORTANT SAFETY

INSTRUCTIONS

When using an electrical appliance, basic safety precautions should always be followed, including

the followings:

Read all instructions before using this appliance.

DANGER

– To reduce the risk of electric shock:

1. An appliance should never be left unattended when plugged in. Always unplug this sewing

machine from the electric outlet immediately after using and before cleaning.

2. Always unplug before replacing a sewing machine bulb. Replace bulb with same type rated

15 Watts.

WARNING

–

To reduce the risk of burns, fire, electric shock,or injury to persons:

1. Do not allow to be used as a toy. Close attention is necessary when this sewing machine

is used by or near children.

2. Use this appliance only for its intended use as described in this owner’s manual.

Use only attachments recommended by the manufacturer as contained in this owner’s

manual.

3. Never operate this sewing machine if it has a damaged cord or plug, if it is not working

properly, if it has been dropped or damaged, or dropped into water.

Return this sewing machine to the nearest authorized dealers or service center for

examination,

repair, electrical or mechanical adjustment.

4. Never operate the appliance with any air opening blocked. Keep ventilation openings of

this sewing machine and foot controller free from accumulation of lint, dust and loose cloth.

5. Never drop or insert any object into any opening.

6. Do not use outdoors.

7. Do not operate where aerosol (spray) products are being used or where oxygen is being

adminis-tered.

8. To disconnect, turn all controls to the off (“O”) position, then remove plug from outlet.

9. Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.

10. Keep fingers away from all moving parts. Special care is required around the sewing

machine needle.

11. Always use the proper needle plate. The wrong plate can cause the needle to break.

12. Do not use bent needles.

13. Do not pull or push fabric while stitching. It may deflect the needle causing it to break.

14. Switch this sewing machine off (“O”) when making any adjustment in the needle area,

such as threading the needle, changing the needle, threading the bobbin or changing the

presser foot, and the like.

15. Always unplug this sewing machine from the electrical outlet when removing covers,

lubricating, or when making any other adjustments mentioned in this owner’s manual.

SAVE THESE INSTRUCTIONS

Designs and specifications are subject to change without prior notice.

MODEL HF106

1 2 3 4 5 6 7 Next › »

Summary of HF106

Page 1
Important safety instructions when using an electrical appliance, basic safety precautions should always be followed, including the followings: read all instructions before using this appliance. Danger – to reduce the risk of electric shock: 1. An appliance should never be left unattended when plugg...
Page 2
1. Thread guide 2. Thread take-up lever 3. Tension dial unit 4. Extension table 5. Presser foot lifter 6. Reverse button 7. Pattern selector dial 8. Handwheel 9. Bobbin winder stopper 10. Bobbin winder spindle 11. Bobbin winder thread guide 12. Spool pin bobbins seam ripper felt needles buttonhole f...
Page 3
To replace: loosen the setscrew and remove the face plate to the direction of arrow. Turn the bulb counterclockwise to remove it. Turn t the bulb clockwise to replace it. The spool pin holds the spool of thread for feeding the thread to the machine. Pull out the spool pin and place the felt on it. 8...
Page 4
12. Threading the bobbin case place the bobbin into the bobbin case. Make sure the thread unwinds in the direction of the arrow. Pull the thread into the bobbin case slit. Draw the thread under the tension spring and into the delivery eye. Pull out about 4” (10 cm) of the thread. 13. Threading the m...
Page 5
1.5 2.5 4 2 - 6 2 3.5 5 2 - 5 raise the needle above the fabric. Turn the dial to select the desired pattern. Note: do not turn the dial when the needle is down in the fabric, otherwise the needle and fabric could be damaged. Press the reverse button to sew in reverse. Machine setting stitch thread ...
Page 6
2 - 5 1 - 5 a b 1 2 3 4 5 6 7 19. Tricot stitch thread tension dial machine setting place the fabric under the presser foot so that the edge is just inside the right side of the presser foot. Guide the fabric so the right hand stitches fall at the edge of the fabric. 20. Buttonhole machine setting s...
Page 7
1 - 4 0.4 - 0.7 cm 3 - 9 machine setting stitch thread tension dial fabric preparation: fold up the fabric as shown. Lower the foot, stitch slowly for better control so that the needle catches the folded edge at the leftmost position. Spread the fabric flat with the right side up. 21. Blind hemming ...
Page 8
Care of your machine 25. Cleaning the feed dog remove the needle and presser foot. Remove the 2 setscrews and remove the needle plate. Clean out dust and lint clogging on the feed dog with a lint brush. Replace the needle plate and secure it with the setscrew. 26. Dismantling and assembling the hook...