Proprietary notice all rights reserved by janz tec ag. No parts of this technical manual may be modified, copied or reproduced in any form or by any means for commercial use without the prior written permission of janz tec ag, germany. All instructions, information and specification contained in thi...
Title: file: j:\as\entwicklung\projekte\hw\empc\empc_x1600\doc\manual\manual_empc- x1600_hardware.Doc pattern: z:\text\vorlagenormal.Dot created: stefan althöfer, 21.06.2011 last update: stefan althöfer, 22.03.2013 © janz tec ag 2013 im dörener feld 8 d-33 100 paderborn, germany tel.: +49-5251-155...
Empc-x1600 (hardware manual) • contents i rev. 1.1 © janz tec ag contents 1 introduction 5 1.1 features ...............................................................................................................................5 1.1.1 standard products ..............................................
Ii empc-x1600 (hardware manual) • contents © janz tec ag rev. 1.1 list of figures figure 1: empc-x1600/0 interfaces .........................................................................................................9 figure 2: empc-x1600/1 interfaces ..............................................
Empc-x1600 (hardware manual) • contents iii about this manual this is the hardware manual for the empc-x1600 embedded pc. It starts with an introduction to the empc-x1600. After that it discusses some topics about installation of the product. The rest of the manual then covers technical details abou...
Empc-x1600 (hardware manual) • introduction 1 - 5 rev. 1.1 © janz tec ag 1 introduction the empc-x1600-platform is a flexible computer system. It consists of one cpu board and can be expanded with a variety of io expansion boards. The boards are stacked together and are inserted into a rail mounted ...
1 - 6 empc-x1600 (hardware manual) • introduction © janz tec ag rev. 1.1 • internal expansion bus (ix-bus) • system power supply 9..32 vdc • reset push button and power led • 2 male 9pin d-sub connectors, utilized by serial ports or can (see table above) • power supply monitor 1.1.2 hardware customi...
Empc-x1600 (hardware manual) • safety instructions 2 - 7 2 safety instructions refer to page iii for explanation of the warning notice system. The product described in this documentation may be operated only by personnel qualified for the specific task in accordance with the relevant documentation f...
3 - 8 empc-x1600 (hardware manual) • installation/maintenance 3 installation/maintenance warning the empc-x1600 is designed as a fan less computer system. Nevertheless a certain amount of heat is generated inside the housing. The housing transports this heat to the environment. Caution when touching...
Empc-x1600 (hardware manual) • interfaces 4 - 9 4 interfaces the empc-x1600 is equipped with differing interfaces. The following interfaces are common for all systems: dvi-d, 3 x usb 2.0, 1 x 10/100 mbit/s ethernet and 1 x 10/100/1000 mbit/s ethernet. Depending on which alternative was ordered addit...
4 - 10 empc-x1600 (hardware manual) • interfaces 4.1 power supply, reset and power led the power supply connector is implemented with a phoenix contact plug type mc1,5/3-st1f-5,08 bf and is included in delivery. The assignment of this connector is shown in figure 5 and table 3. Reset power 24vdc s p...
Empc-x1600 (hardware manual) • interfaces 4 - 11 table 5: rs232 connector 4.4 rs485 in the rs485 variant, there are only the differential signals d+ and d- provided. The transceiver is enabled to send data, when rts# of the corresponding uart is low. Data received on the rs485 will always be seen on...
4 - 12 empc-x1600 (hardware manual) • interfaces 4.7 usb type a receptacle usb0, usb1 and usb2 two usb 2.0 interfaces are available at the front panel. 1 +5v, i max = 500 ma 2 usb- 3 usb+ 4 gnd table 9: usb connector 1 notice although each port can deliver supply current of 500 ma, the overall load ...
Empc-x1600 (hardware manual) • system internals 5 - 13 5 system internals the empc-x1600 is built upon a couple of standard building blocks, as shown in figure 6. Q7 module (cpu engine) ixbus q7 carrier ixbus power supply and communication module expansion bus uart (console) cfast socket figure 6: s...
6 - 14 empc-x1600 (hardware manual) • appendices © janz tec ag rev. 1.1 6 appendices 6.1 technical data cpu type x1600: intel atom z530 x1100: intel atom z510 clock frequency 1.6 ghz 1.1 ghz front side bud 533 mhz 400 mhz hyper threading yes no l1-cache 32 kb instruction, 24 kb data l2-cache 512 kb ...
Empc-x1600 (hardware manual) • appendices 6 - 15 rev. 1.1 © janz tec ag power supply input 9..32 v dc selv consumption 15 w (max) inverse-polarity protection yes fuse internal melting fuse in dc in, gnd is unfused potential separation no, gnd (pin 3 in table 3) is connected to case housing dimension...
6 - 16 empc-x1600 (hardware manual) • appendices © janz tec ag rev. 1.1 6.2 references these references direct you to manuals and specifications that you need to when developing programs for the empc/x1600. Most of the documents can be downloaded from the internet. Look for the www servers of the ch...
Empc-x1600 (hardware manual) • appendices 6 - 17 rev. 1.1 © janz tec ag 6.3 product history 6.3.1 empc-x1600 (/0, /1, /2) version release date name changes v1.0 • initial version v1.1 11.08.2011 as • optional cfast socket • optimized usb connector position v1.2 23.05.2012 as • improved cpu cooling w...
6 - 18 empc-x1600 (hardware manual) • appendices © janz tec ag rev. 1.1 6.4 manual history version release date name changes v1.0 26.08.2011 as • initial release v1.1 13.03.2013 as • changed to janz tec • restructured technical data • added total power limitation for usb connectors • fixed missing g...
