1. DL manuals
  2. Janz Tec
  3. Touch Panel
  4. emVIEW-12T/D
  5. User Manual

Janz Tec emVIEW-12T/D User Manual

Summary of emVIEW-12T/D

  • Page 1

    Emview-12t/d (user's manual) introduction 1 - 1 rev. 1.3 © janz tec ag refers to product revision v 1.5 emview-12t/d human machine interface system (user's manual) version 1.3 proprietary notice all rights reserved by janz tec ag. No parts of this technical manual may be modified, copied or reproduc...

  • Page 2

    1 - 2 emview-12t/d(user's manual) introduction © janz tec ag rev. 1.3 title: emview-12t/d hardware manual file: j:\as\entwicklung\projekte\hw\empc\emview\12_zoll\emview_abgesetzt\doc\ma nual_emview_12td.Doc pattern: j:\as\entwicklung\formulare\entwicklung (ew)\ew_manual.Dot created: ime, 07.01.2009 ...

  • Page 3: Contents

    Emview-12t/d (user's manual) introduction 1 - 3 rev. 1.3 © janz tec ag contents 1 introduction 6 1.1 features ............................................................................................................................... 6 1.2 functional overview .......................................

  • Page 4: List Of Figures

    1 - 4 emview-12t/d(user's manual) introduction © janz tec ag rev. 1.3 list of figures figure 1: emview-12t/d front view .......................................................................................................... 2 figure 2: emview-12t/d side view .........................................

  • Page 5: Conventions

    Emview-12t/d (user's manual) introduction 1 - 5 rev. 1.3 © janz tec ag conventions if numbers are specified in this manual, they will be either decimal or hexadecimal. We use c-notation to identify hexadecimal numbers (the 0x prefix). If we refer to low active signal names, they will suffixed by a “...

  • Page 6: Introduction

    1 - 6 emview-12t/d(user's manual) introduction © janz tec ag rev. 1.3 1 introduction janz tec ag’s emview systems are an additional development. These hmi systems and industrial display solutions are a combination of the familiar janz empc systems with a wide range of lcds, with or without touch-scr...

  • Page 7

    Emview-12t/d (user's manual) introduction 1 - 7 rev. 1.3 © janz tec ag figure 2: emview-12t/d side view.

  • Page 8: Safety Instructions

    2 - 8 emview-12t/d(user's manual) safety instructions © janz tec ag rev. 1.3 2 safety instructions refer to page 5 for explanation of the warning notice system. The product described in this documentation may be operated only by personnel qualified for the specific task in accordance with the releva...

  • Page 9: Installation

    Emview-12t/d (user's manual) installation 3 - 9 rev. 1.3 © janz tec ag 3 installation when opening the shipping package of the emview-12t/d, the contents of the package should be checked immediately. The emview-12t/d is delivered in a configured state, but the configurations can be adjusted by the u...

  • Page 10

    3 - 10 emview-12t/d(user's manual) installation © janz tec ag rev. 1.3 figure 4: emview-12t/d cut-out and holes * † * not true to scale † refers to drawing drill_jig_emv12_rev1 320 mm 2 6 0 m m 2 4 0 m m 300 mm 8 m m 2 5 2 m m 8 mm 109 mm 312 mm 211 mm hole for m5 screws 1 3 0 m m 10 mm 1 0 m m.

  • Page 11

    Emview-12t/d (user's manual) installation 3 - 11 rev. 1.3 © janz tec ag 3.2 technical specification the emview-12t/d has five connectors, the main power supply, a serial interface and usb connector, vga and dvi-d connector. Figure 5 shows a block diagram of the internal function. Figure 5: block dia...

  • Page 12

    3 - 12 emview-12t/d(user's manual) installation © janz tec ag rev. 1.3 3.2.2 serial interface - rs232 the emview-12t/d provides a serial interface to connect the touch-screen to a host computer. If the usb is connected to the host the serial interface chip is deactivated. The pin assignment of the 9...

  • Page 13

    Emview-12t/d (user's manual) installation 3 - 13 rev. 1.3 © janz tec ag 3.2.6 display the panel is built as a thin film transistor liquid crystal display tft-lcd with a diagonal screen of 12.1’’ and up to 16m colours. Description specification display area 246.0 x 184.5 mm number of dots 800x3 (h) x...

  • Page 14

    3 - 14 emview-12t/d(user's manual) installation © janz tec ag rev. 1.3 the license agreement must be confirmed. The location where the driver will be installed to must be chosen..

  • Page 15

    Emview-12t/d (user's manual) installation 3 - 15 rev. 1.3 © janz tec ag after choosing the location the driver will be installed and the device is searched. Is the device found the installation is finished by clicking finish..

  • Page 16

    3 - 16 emview-12t/d(user's manual) installation © janz tec ag rev. 1.3 3.3.2 ubuntu linux driver installation for touch-screen on rs232 or usb download the correct driver for the installed os. In this section the installation on an ubuntu 8.04 is shown. Once the driver is downloaded (ubuntu 8.04 dri...

  • Page 17: Use Of Emview-12T/d

    Emview-12t/d (user's manual) use of emview-12t/d 4 - 17 rev. 1.3 © janz tec ag 4 use of emview-12t/d once the emview is installed it can be used at once, it is already configured. The user is free to adjust the configuration at will. To do so, the installed on screen display (osd) must be used. To f...

  • Page 18

    4 - 18 emview-12t/d(user's manual) use of emview-12t/d © janz tec ag rev. 1.3 on this window the settings for ‘device 0’ are accessible. As seen in figure 8 there are three tabs to configure the touch-screen. The first is for calibrating the device, the second shows settings like ‘touch-mode’, ‘curs...

  • Page 19

    Emview-12t/d (user's manual) use of emview-12t/d 4 - 19 rev. 1.3 © janz tec ag the calibration screen is looking like that. The calibration is finished by clicking the red squares..

  • Page 20

    4 - 20 emview-12t/d(user's manual) use of emview-12t/d © janz tec ag rev. 1.3 4.3 adjusting the display on the backside of the emview-12t/d there are five buttons. The first button is on/off, it controls the backlight and display controller. The serial interface and the usb interface are kept alive....

  • Page 21

    Emview-12t/d (user's manual) use of emview-12t/d 4 - 21 rev. 1.3 © janz tec ag color settings menu wizard auto adjusts the colours. Color temperatur different colour temperature profiles. Exit to exit this menu. Table 9: color settings menu image settings menu wizard auto adjusts the position of the...

  • Page 22: Technical Data

    5 - 22 emview-12t/d(user's manual) technical data © janz tec ag rev. 1.3 5 technical data interfaces usb the usb port is for connecting the touch screen with a computer system. Thereby the serial port is tunnelled through usb virtual com port. Serial port rs232 the serial port connects the touch con...

  • Page 23: Product History

    Emview-12t/d (user's manual) product history 6 - 23 rev. 1.3 © janz tec ag 6 product history note that changes in the major version number are related to a pcb redesign. Though, pcb redesign need not be related to functional changes, but might have been done for manufacturing purposes only. Version ...