Service manual issue: 06/2008 4045-sme-000e.
Taiko service manual 2 pr eface © 2006 japan cash machine co.Ltd. All rights reserved. Preface thank you for purchasing jcm’s taiko bill acceptor. Please be sure to read the follow- ing and any related documents thoroughly to understand the correct operation and features of this unit. Note 1. It is ...
3 taiko service manual pr eface © 2006 japan cash machine co.Ltd. All rights reserved. - when using the acceptor in a location where the air is subject to the car exhaust emis- sions or cigarette smoke, be sure to clean and maintain the unit at regular intervals. wiring - when installing the taiko...
Taiko service manual 4 pr eface © 2006 japan cash machine co.Ltd. All rights reserved. Product configurations taiko unit’s are configured as follows. [model] pub-* [type] *** - * * * * - ** a b c d e f g a. Validation method 7: optical/transparency/reflection 11: optical/transparency/reflection/mag ...
5 taiko service manual pr eface © 2006 japan cash machine co.Ltd. All rights reserved. Package contents the following items are contained within the taiko package. taiko unit installation guide - this unit has been carefully packed, with special attention taken in regard to quality. However if you...
Taiko service manual 6 pr eface © 2006 japan cash machine co.Ltd. All rights reserved. Ce marking note declaration of conformity manufacturer name : japan cash machine co., ltd. Address : 3-15, 2-chome, nishiwaki, hirano-ku, osaka, 547-0035 japan phone : +81-6-6703-8405 fax : +81-6-6704-7843 details...
7 taiko service manual pr eface © 2006 japan cash machine co.Ltd. All rights reserved. Documentation conventions the list below describes the documentation convertions used in this manual. Icon/mark descriptions this icon indicates important information or procedures that must be followed for correc...
Taiko service manual 8 pr eface © 2006 japan cash machine co.Ltd. All rights reserved. Table of contents preface preface ............................................................................................................................. 2 note .................................................
9 taiko service manual pr eface © 2006 japan cash machine co.Ltd. All rights reserved. 2-4. External dimensions .......................................................................................... 2-11 2-4-1. When installing the type 1/ type 2/ type 3 faceplate with taiko unit ...................
Taiko service manual 10 pr eface © 2006 japan cash machine co.Ltd. All rights reserved. 5-2. Trouble shooting .................................................................................................. 5-2 5-2-1. General troubles ..................................................................
Chapter 1 introduction 1-1. Main features 1-2. Prior to use 1-3. Component names 1-4. System configuration 1-5. Operation flowchart issue: 06/2008 4045-sme-001d.
Taiko service manual 1-2 chapter 1 © 2006 japan cash machine co.Ltd. All rights reserved. 1-1. Main features in this section, taiko unit’s main features are explained. easy installation installation/removal of taiko unit is very easy in the clip-on style. Anyone can install the taiko unit easily. ...
1-3 taiko service manual © 2006 japan cash machine co.Ltd. All rights reserved. Chapter 1 1-2. Prior to use be sure to follow these steps when creating the project for taiko unit. 1. Preparation before using taiko unit, check the all required hardware is present and read all specification, wiring, a...
Taiko service manual 1-4 chapter 1 © 2006 japan cash machine co.Ltd. All rights reserved. 1-3. Component names top right bottom rear front c g l d k m h a b f left i j j e a. Faceplate b. Led lamp c. Upper lid d. Lower lid e. Lower lid lock button f. Bill insertion slot g. Bill ejection slot h. Inte...
1-5 taiko service manual © 2006 japan cash machine co.Ltd. All rights reserved. Chapter 1 1-4. System configuration the following diagram represents the standard items can be connected to the taiko unit. Maintenace connector interface connector taiko harness a (edp# 127527, part# 3280-05-54) jcm pow...
Taiko service manual 1-6 chapter 1 © 2006 japan cash machine co.Ltd. All rights reserved. 1-5. Operation flowchart power on initializing idling accept bill? Led on insert bill? Transport bill (scanning bill date) stop feeding bill validation ok? Accepted bill? Output denomi signal b led off a d no n...
1-7 taiko service manual © 2006 japan cash machine co.Ltd. All rights reserved. Chapter 1 output vend signal completed? Completed 㧫 retry carrying out carry out bill (carry out to cashbox) b a d no yes yes completed no stop led red blink *1 reject bill completed? Completed? Retry rejection b no no s...
Taiko service manual 1-8 chapter 1 © 2006 japan cash machine co.Ltd. All rights reserved. N o t e.
Chapter 2 specifications taiko service manual 2-1. Specifications 2-2. Connector 2-3. Interface circuit 2-4. External dimensions 2-5. Dip switch settings issue: 10/2007 4045-sme-002j.
Taiko service manual 2-2 chapter 2 © 2006 japan cash machine co., ltd.. All rights reserved. 2-1. Specifications 2-1-1. Basic technical specifications *1 may differ depending on the software for your country. For details, refer to the software information sheet. *2 can be selected using the dip swit...
2-3 taiko service manual © 2006 japan cash machine co., ltd. All rights reserved. Chapter 2 2-1-4. Installation specifications installation *1 door holizontal mounting (no vibration) weight approx. 0.6 kg external dimentions with type 1/2/3 faceplate: 124mm (w) x 88mm (h) x 145.2mm (d) with type 5 f...
Taiko service manual 2-4 chapter 2 © 2006 japan cash machine co., ltd.. All rights reserved. 2-2. Connector pin no. Signal name i/o *1 function 1 cct alk+ in/out cct alk send/receive line 2 nc not connected 3 nc not connected 4 nc not connected 5 nc not connected 6 nc not connected 7 vcc 12v dc powe...
2-5 taiko service manual © 2006 japan cash machine co., ltd. All rights reserved. Chapter 2 pin no. Signal name i/o *1 function 1 nc - not connected 2 nc - not connected 3 rxd- 4 rxd+ 5 t xd- 6 t xd+ 7 vcc - 12v dc power supply 8 vss - power supply gnd 9 nc - not connected 10 nc - not connected in o...
Taiko service manual 2-6 chapter 2 © 2006 japan cash machine co., ltd.. All rights reserved. Pin no. Signal name i/o *1 function 1 vcc - 12v dc power supply 2 vcc - 12v dc power supply 3 vss - power supply gnd 4 nc - not connected 5 ack ack signal receive line 6 rej rej signal receive line 7 inh inh...
2-7 taiko service manual © 2006 japan cash machine co., ltd. All rights reserved. Chapter 2 2-3. Interface circuit pw12v 12v±5% gnd/cctalk 7 8 cn1 1 2 gnd reserve d5v pw12v r12 22k d5v r14 22k d5v cctalk reserve reserve 4 3 6 reserve 5 reserve nc 9 d1 7 rb520s-30 d1 8 1ss400 r1 10k 3 4 ic1b sn74lv 1...
Taiko service manual 2-8 chapter 2 © 2006 japan cash machine co., ltd.. All rights reserved. Pw12v 12v±5% gnd 7 8 cn1 1 2 gnd reserve r10 1k 1/4w reserve rxd - txd - 5 6 3 txd + 4 rxd + mdb/id003 r9 1k 1/4w nc 9 r15 22k d5v r24 470Ω d5v pw12v pwgnd 9 8 ic1d sn74lv14a 3 4 2 1 pc2 ps2811(k) 3 4 2 1 pc...
2-9 taiko service manual © 2006 japan cash machine co., ltd. All rights reserved. Chapter 2 2-3-3. Pulse interface circuit pw12v 12v±5% gnd 7 8 cn1 1 2 pwgnd reserve r10 1k 1/4w rxd - txd - 5 6 3 txd + 4 rxd + r9 1k 1/4w nc 9 pulse r15 22k d5v r24 470Ω d5v pw12v pwgnd 9 8 ic1d sn74lv14a 3 4 2 1 pc2 ...
Taiko service manual 2-10 chapter 2 © 2006 japan cash machine co., ltd.. All rights reserved. 2-3-4. Id-001(parallel) interface circuit 0 % r ޓ 8 r ޓ 8 & 0 ) - % # , ' 4 * 0 + & + . # 8 & 0 ' 8 & 0 ' 8 & 0 ' 8 ; 5 7 $ 0 $ # ( - 6 5 ' 8 4 ' 5 ' 4 ' 8 4 ' 5 ' 4 ' 8 4 ' 5 ' 4 v 2 1 c d d n g r ޓ 8 r ޓ ...
2-11 taiko service manual © 2006 japan cash machine co., ltd. All rights reserved. Chapter 2 2-4 . External dimensions 2-4-1. When installing the type1/type2/type3 faceplate with taiko unit 18 98 47.2 42.7 (door installation position) 88 17.6 51 (bill ejection position) 3.2 2 to 6mm (panel thickness...
Taiko service manual 2-12 chapter 2 © 2006 japan cash machine co., ltd.. All rights reserved. 2-4-2. When installing the type5 faceplate with taiko unit 25.4 20 45 98 ‚2 㨪6mm(panel thickness) 38.3 (door installation position) 88 51(bill ejection position) 3 125 103 (door installation position) 100 6...
2-13 taiko service manual © 2006 japan cash machine co., ltd. All rights reserved. Chapter 2 2-5. Dip switch settings the communication method and various functions of the taiko unit can be set with the dip switches on the left side of the unit. On off 1 test mode *1 normal mode 2 double-scan mode *...
Taiko service manual 2-14 chapter 2 © 2006 japan cash machine co., ltd.. All rights reserved. *1 for details about the test mode, refer to 5-3. Test mode. *2 the acceptance rate will be improved but operation time will be increased if a banknote is rejected. *3 fishing prevention will be improved bu...
2-15 taiko service manual © 2006 japan cash machine co., ltd. All rights reserved. Chapter 2 8 7 6 5 4 3 2 1 on denomination setting mode (this mode is for only id-003 (serial)/ mdb/ pulse/ cctalk specification. Denomination settings “inhibit”/”accept” are set by dip switches (see=>2-5-2) for id-001...
Taiko service manual 2-16 chapter 2 © 2006 japan cash machine co., ltd.. All rights reserved. 8 7 6 5 4 3 2 1 on 8 7 6 5 4 3 2 1 on led pattern setting mode the led pattern can be changed according to your perference. Select between pattern 1 and pattern 2. The default setting is pattern 1. T define...
2-17 taiko service manual © 2006 japan cash machine co., ltd. All rights reserved. Chapter 2 when using cctalk communication(encryption)mode and the encryption code is unknown perform the encryption code initialisation setting to improve the encryption to the last 6 didgits of the taiko serial numbe...
Chapter 3 installation/ operation 3-1. Installation/removal 3-2. Wiring 3-3. Clearing a banknote jam issue: 06/2008 4045-sme-003d.
Taiko service manual 3-2 chapter 3 © 2006 japan cash machine co.Ltd. All rights reserved. 3-1. Installation/removal this section describes the procedures for installing of taiko unit. Perform the following procedure when installing the taiko unit. 1. Use the panel cutting dimensions given below and ...
3-3 taiko service manual chapter 3 © 2006 japan cash machine co.Ltd. All rights reserved. Faceplate brackets hexagonal nuts 4. Press down slightly on the faceplate and raise up on the taiko unit. Slide the taiko unit up and back to detach it from the faceplate. Back and up to detach it from the face...
Taiko service manual 3-4 chapter 3 © 2006 japan cash machine co.Ltd. All rights reserved. Click 7. Hold in the upper cover open/close buttons once again, open the upper cover, and grasp the taiko unit with your hand under the upper cover. 8. Insert the faceplate installation guide pin into the facep...
3-5 taiko service manual chapter 3 © 2006 japan cash machine co.Ltd. All rights reserved. 3-2. Wiring socket rock lever socket xg5m-1032-n (omron) socket for flat cable xg4m-1030-t (omron) semi cover xg5x-0501 (omron) - rock lever ii xg4z-0002 (omron) - applicable wires ul1061 awg24 1.27 mm pitch fl...
Taiko service manual 3-6 chapter 3 © 2006 japan cash machine co.Ltd. All rights reserved. 3-2-2. Wiring procedure perform the following procedure when connecting the power harness. 1. Confirm that there is no power being supplied to the power harness. 2. Connect the power harness to the taiko unit’s...
3-7 taiko service manual chapter 3 © 2006 japan cash machine co.Ltd. All rights reserved. 3-3. Clearing a banknote jam when a banknote becomes jammed inside the taiko unit, follow the instructions below to remove the jammed banknote. - be sure to turn off the power to the taiko unit when opening the...
Chapter 4 download & adjustment taiko service manual 4-1. Download 4-2. Adjustment 4-3. Palm 4-4. Cloning issue: 11/2007.
Taiko service manual 4-2 chapter 4 © 2006 japan cash machine co.Ltd. All rights reserved. 4-1. Download the software download procedure is described in this section. When the software has been upgraded or the taiko unit’s cpu board has been replaced, please download the software to the taiko unit. W...
4-3 taiko service manual chapter 4 © 2006 japan cash machine co.Ltd. All rights reserved. Jcm power supply unit (part#: vm-30, edp#:116125) or equivalent taiko to ac power serial port taiko harness b (part#: 3280-03-11, edp#:116488) pc (os: windows (r) 98 se/2000/xp) taiko harness a (part#:3280-05-5...
Taiko service manual 4-4 chapter 4 © 2006 japan cash machine co.Ltd. All rights reserved. 4-1-3. Download procedure when downloading software, follow the steps as shown bellow. 1. Double click the download program ver. 1.21.Exe. The following window will be appear. 2. Select your pc’s com port # fro...
4-5 taiko service manual chapter 4 © 2006 japan cash machine co.Ltd. All rights reserved. 4-1-4. Writing serial no. When replacing cpu board, follow the steps below and write serial no.. 1. Double click serialno.Exe and then the following window will appear. 2. Click [read serial number] button and ...
Taiko service manual 4-6 chapter 4 © 2006 japan cash machine co.Ltd. All rights reserved. 4-2. Adjustment you learn how to adjust taiko unit in this section. After software program is downloaded or cpu/sensor board is replaced, the taiko unit needs to be adjusted. 4-2-1. Requirements when adjusting ...
4-7 taiko service manual chapter 4 © 2006 japan cash machine co.Ltd. All rights reserved. Reference paper (ks-070) 4. Turn on the power to the taiko unit. Confirm that taiko’s white led lamp is flashing. 5. Set the dip switch no.1 off and confirm that taiko’s green led lamp lights. 6. Insert the ref...
Taiko service manual 4-8 chapter 4 © 2006 japan cash machine co.Ltd. All rights reserved. 4-3. Palm download procedure using palm is described in this section. 4-3-1. Requirement when adjusting taiko unit, the following items are required. - palm (palm(r)’s tungsten c) - taiko harness b (part#: 3280...
4-9 taiko service manual chapter 4 © 2006 japan cash machine co.Ltd. All rights reserved. 4-3-3. Converting software program follow the steps below, convert the software program into prc format. 1. Double click the pdbconven.Exe icon to start the pdbconven. The following window will appear. 2. Confi...
Taiko service manual 4-10 chapter 4 © 2006 japan cash machine co.Ltd. All rights reserved. Palm (r) tungsten c taiko taiko harness b (part#: 3280-03-11, edp#: 116488) to maintenace connector interface connector(10 pin) maintenance connector(4 pin) jcm power supply unit (part#: vm-30, edp#: 116125) o...
4-11 taiko service manual chapter 4 © 2006 japan cash machine co.Ltd. All rights reserved. 4-4. Cloning using the clone harness, the software can be copied from the master taiko unit to salve taiko unit. (cloning) 4-4-1. Required items when cloning, the following items are required. - taiko unit ins...
Taiko service manual 4-12 chapter 4 © 2006 japan cash machine co.Ltd. All rights reserved. 3. Confirm the led lamp of the master taiko unit is flashing withe, the led lamp of the slave taiko unit is flashing green. 4. Set the dip switch of the master taiko unit no. 1 off to start cloning. 5. When st...
Chapter 5 trouble shooting / maintenance taiko service manual 5-1. Error codes 5-2. Trouble shooting 5-3. Test mode (diagnostics) 5-4. Cleaning 5-5. Maintenance tool lists 5-6. Wiring diagrams 5-7. Product support issue: 06/2008 4045-sme-005g.
Taiko servic e manual 5-2 chapter 5 © 2006 japan cash machine co.Ltd. All rights reserved. 5-1. Error codes number of red flashes of the led lamp indicates the error of taiko unit. Led lamp is located in the middle of the faceplate. See=> 1-3. Component names 5-1-1. Error codes # of flashes diagnost...
5-3 taiko service manual chapter 5 © 2006 japan cash machine co.Ltd. All rights reserved. Symptom/error message possible causes recovery action acceptor is not working. (acceptor does not accept any bills.) entrance sensor is not working or there is any foreign object at the entrance. Remove the for...
Taiko servic e manual 5-4 chapter 5 © 2006 japan cash machine co.Ltd. All rights reserved. Symptom/error message possible causes recovery action reference paper is wrong. Use the reference paper (ks-070) for taiko. Cpu/sensor board failure. Replace the cpu/sensor board. See=> chapter 6 replacement p...
5-5 taiko service manual chapter 5 © 2006 japan cash machine co.Ltd. All rights reserved. 5-2-3. Communication troubles - when you cannot solve the problem even if you follow the in- struction above, please contact jcm. See => 5-7. Product support symptom/error message possible causes recovery actio...
Taiko servic e manual 5-6 chapter 5 © 2006 japan cash machine co.Ltd. All rights reserved. 5-3. Test mode (diagnostics) taiko has the diagnostics function. Taiko can be specified the part of the error using the diagnostic funktion. 5-3-1. Dip switch setting list test items sw1 sw2 sw3 sw4 sw5 sw6 sw...
5-7 taiko service manual chapter 5 © 2006 japan cash machine co.Ltd. All rights reserved. # of flashes sensor position 1 rom error 2 jam inside acceptor 3 bill remains inside transport path 4 adjustment error 5 motor error 6 entrance solenoid error 7 exit solenoid error 8 sensor operation at the abn...
Taiko servic e manual 5-8 chapter 5 © 2006 japan cash machine co.Ltd. All rights reserved. 5-3-6. Solenoid test procedure test the condition of the solenoids. 1. Set the switch nos.1, 2, 3 and 4 on and turn on the power to the taiko unit. 2. Set the switch no.1 off to start the test. The taiko unit ...
5-9 taiko service manual chapter 5 © 2006 japan cash machine co.Ltd. All rights reserved. 5-3-8. Entrance flapper test procedure test the entrance flapper. 1. Set the switch nos.1, 4 and 5 on and turn the power to the taiko unit. 2. Set the switch no.1 off to start the test. Then the entrance flappe...
Taiko servic e manual 5-10 chapter 5 © 2006 japan cash machine co.Ltd. All rights reserved. 5-4. Cleaning if the paper dust or foreign object spotted in the acceptor parts, the acceptance rate may go down. Clean the acceptor parts once a month. Wipe out on the sensor with lint-free cloth or cotton b...
5-11 taiko service manual chapter 5 © 2006 japan cash machine co.Ltd. All rights reserved. 5-5. Maintenance tool list when maintenace or adjust taiko unit, the following parts need to be parchased. Items edp# part# description power supply unit 116125 vm-30 this unit is to supply the power to taiko ...
Taiko servic e manual 5-12 chapter 5 © 2006 japan cash machine co.Ltd. All rights reserved. 5-6. W iring diagram 5-6-1. Pub-7 w iring diagram encoder sensor 3280-06-03 t ransport motor 20pc1212 3280-05-02 3280-05-03 sensor board (3280-06-02b) cn1 cn3 cn1 cn4 cn2 3280-05-01 3280-05-04 cn3 cn4 cn5 cn6...
5-13 taiko service manual chapter 5 © 2006 japan cash machine co.Ltd. All rights reserved. 5-6-2. Pub-1 1 w iring diagram encoder sensor 3280-06-03 t ransport motor 20pc1212 3280-05-02 3280-05-03 cn1 sensor board (3280-06-02b) cn3 cn1 nir/b b/nir ptr ptr r/ir r/ir cn4 cn2 3280-05-01 3280-05-04 cn3 c...
Taiko servic e manual 5-14 chapter 5 © 2006 japan cash machine co.Ltd. All rights reserved. 5-7. Product support if you happen to experience any problems or errors with your taiko unit, or have any inquiries regarding your unit, consult with your nearest jcm contact as shown below. Please be sure to...
Chapter 6 replacement procedure taiko service manual 6-1. Replacement of faceplate guide 6-2. Replacement of cpu board 6-3. Replacement of mag board (pub-11 only) 6-4. Replacement of sensor board 6-5. Replacement of encoder board/ motor unit 6-6. Replacement of solenoid issue: 06/2008 4045-sme-006d.
Taiko service manual 6-2 chapter 6 © 2006 japan cash machine co.Ltd. All rights reserved. 6-1. Replacement of faceplate guide when replacing the faceplate guide, follow the instructions below. 1. Take out two (2) screws from bihind the faceplate unit. 2. Remove a (1) faceplate guide from the facepla...
6-3 taiko service manual chapter 6 © 2006 japan cash machine co.Ltd. All rights reserved. 6-2. Replacement of cpu board when replacing the cpu board, follow the instructions below. 1. Insert your fingernail into the gap of left or right side of the upper lid. Lift up the upper lid cover with your fi...
Taiko service manual 6-4 chapter 6 © 2006 japan cash machine co.Ltd. All rights reserved. 6-3. Replacement of mag board (pub-11 only) the mag board is mounted in the pub-11 unit. When replacing the mag board, follow the instructions below. 1. Take out a connector and two (2) screws from the mag boar...
6-5 taiko service manual chapter 6 © 2006 japan cash machine co.Ltd. All rights reserved. 6-4. Replacement of sensor board when replacing the sensor board, follow the instructions below. 1. Take out two (2) screws from the both left and right side of the taiko unit. 2. Remove a upper lid, side cover...
Taiko service manual 6-6 chapter 6 © 2006 japan cash machine co.Ltd. All rights reserved. 3. Remove the transport unit form the lower base. 4. Take out three (3) screws each from the both side of the transport unit. Remove the center guide..
6-7 taiko service manual chapter 6 © 2006 japan cash machine co.Ltd. All rights reserved. 5. Remove the feed roller assy of the both side of the center unit. Take out three (3) washers each from the both side of the center unit. 6. Insert the minus driver or equivalent into the encircled area as sho...
Taiko service manual 6-8 chapter 6 © 2006 japan cash machine co.Ltd. All rights reserved. 7. Take out a (1) screw and a (1) prism from the center guide a. 8. Take out two (2) screws on the sensor board. Slide aside the sensor board and re- move it from the center guide a..
6-9 taiko service manual chapter 6 © 2006 japan cash machine co.Ltd. All rights reserved. 6 -5 . Replacement of encoder board/motor unit when replacing the encoder board and motor unit, follow the instructions below. 1. Take out a (1) screw from the center guide b (refer replacement procedure 6. Of ...
Taiko service manual 6-10 chapter 6 © 2006 japan cash machine co.Ltd. All rights reserved. 6 -6. Replacement of solenoid when replacing the entrance and exit solenoid, follow the instructions below. 1. Take out two (2) screws from the lower guide and then remove the guide assy. 2. Put the lower guid...
6-11 taiko service manual chapter 6 © 2006 japan cash machine co.Ltd. All rights reserved. 3. Remove two (2) guide levers from the lower guide. 4. Take out two (2) screws and then remove a (1) entrance and a (1) exit solenoid..
Chapter 7 exploded view/ parts list taiko service manual 7-1. Entire unit & option 7-2. Taiko (pub-7/pub-11) unit 7-3. Bezel unit issue: 05/2008 4045-sme-007h.
Taiko service manual 7-2 chapter 7 © 2006 japan cash machine co.Ltd. All rights reserved. 7-1. Entire unit & option e1 e2 e3 e4 e5 e6 op1 op2 op3 op4 op5 e7 7-1-1. Enter unit & option exploded view.
7-3 taiko service manual © 2006 japan cash machine co.Ltd. All rights reserved. Chapter 7 7-1-2. Enter unit & option parts list n o. Ed p n o. P art n o. D escrip tion remark e1 *1 p u b-7 u nit e2 *1 p u b-11 u nit e3 121872 p u b-7 f acep late for eu r (68mm) t y p e 1 e4 121873 p u b-7 f acep lat...
Taiko service manual 7-4 chapter 7 © 2006 japan cash machine co.Ltd. All rights reserved. 7 39 68 53 42 6 39 84 31 45 6 39 69 79 39 7 60 80 64 82 73 61 30 19 66 78 7 39 73 29 16 24 14 18 59 9 55 86 4 56 26 85 67 32 15 72 13 34 36 62 72 62 27 58 25 17 81 18 54 3 65 74 47 40 37 35 40 38 38 75 75 47 65...
7-5 taiko service manual © 2006 japan cash machine co.Ltd. All rights reserved. Chapter 7 7-2-2. Taiko (pub-7/pub-11) unit parts list no. Edp no. Part no. Description qty. Remark 1 115543 tds-04b-328 enterance solenoid 1 2 115544 tds-04b-327 exit solenoid 1 3 114977 3280-05-01 relay harness (14p) 1 ...
Taiko service manual 7-6 chapter 7 © 2006 japan cash machine co.Ltd. All rights reserved. No. Edp no. Part no. Description qty. Remarks 61 110910 4045re0120a right guide 1 62 110911 4045re0138 prism (d) 2 64 130164 4045re0117b sensor lever 1 65 115494 4045re0150a drive pulley (f) 2 127518:4045as0103...
7-7 taiko service manual © 2006 japan cash machine co.Ltd. All rights reserved. Chapter 7 7-3. Bezel unit 7-3-1. Bezel unit exploded view lower base 207 202 201 206 206 208 207 211 206 206 208 210 203 210 204 208 205 209 211 209 209.
Taiko service manual 7-8 chapter 7 © 2006 japan cash machine co.Ltd. All rights reserved. 7-3-2. Bezel unit parts list no. Edp no. Part no. Description qty. Remarks 201 110884 4045re0135a faceplate 1 110897 4045re0136b pub-7 faceplate guide for eur (68mm) 1 type 1 118069 4045re0158b pub-7 faceplate ...