- DL manuals
- Jaroby
- Indoor Fireplace
- Volcan B12 FOGO
- Installation Manual
Jaroby Volcan B12 FOGO Installation Manual
Summary of Volcan B12 FOGO
Page 1
490, rue de l'argon québec (québec) g2n 2c9 téléphone.: 418-849-8095 fax : 418-849-0077 www.Jaroby.Com revised may 26, 2011 vesuve trident laguna taal designed especially for fireplace hearth kilauea volcan b12 fogo ethanol fireplaces certified as per ulc/ord c627.1-2008 ul subject 1370-2010
Page 2: Table Of Contents
2 table of contents table of contents.................................................................................... 2 characteristics ........................................................................................ 2 fireplace location .....................................................
Page 3: Fireplace Location
3 clearances floor trident and laguna : 12'' (304.8mm) fogo, vesuve and kilauea : combustible lateral wall (left or right) (see p.7 fig. 2) 12'' (304.8 mm) opposite wall (see p.8 fig. 4) 36'' (914.4 mm) rear wall air circulation (see p.9 fig.6) 0'' (0 mm) 1'' (25.4 mm) appliance front 24'' (609.6 mm...
Page 4: Warning
4 warning • never use other liquid than ethanol. Failing this can cause material damages, injuries, fire, explosions or even death. • minimum clearances must be observed. • risk of indoor air pollution – use unvented decorative appliance only in well ventilated areas. People with breathing problems ...
Page 5: Warning
5 warning • risk of explosion - never use any fuel other than the fuels specifically identified for use in the unvented decorative appliance. Never use gasoline. - never store or transport the fuel in other than a metal or plastic container that is: a) acceptable for use with the specific fuel, b) n...
Page 6: Installation On Wall
6 installation on wall a detailed explanation is provided for each model to p.16 à 22 drawings for illustrations purpose only figure 1 to install, follow step 1, 2, 3. 1- insert the wall anchors in the locations designed for it. 2 - secure screws in the anchors and keep 5/16 inch between the head of...
Page 7: Securing The Installation
7 securing the installation model #1: trident, laguna, vésuve et fogo model #2: kilauea secure the installation by fixing two included screws in the places shown in the picture according to your fireplace model. Tighten the screw through the 0.187 inch diameter hole to secure the installation (screw...
Page 8: Location Of Appliance
8 location of appliance figure 2 figure3 from the top of the burner from the top of the burner illustrated model: trident idem for laguna and fogo fireplace. Illustrated model: kilauea.
Page 9
9 figure 4 figure 5 from the top of the burner from the top of the burner illustrated model: kilauea idem for laguna, fogo, trident and vesuve fireplace. Illustrated model: vesuve.
Page 10
10 figure 6 the trident, laguna, fogo and vésuve fireplace are designed to leave a ventilation space between the rear wall and the fireplace to let the air flow easily. Never block this ventilation space. Laguna vésuve trident fogo.
Page 11
11 installation of the window 1- locate both lock brackets inside the home. (see detail a). 2- insert the window in is slot. 3- apply pressure on the locks with your fingers and press them to the window..
Page 12: Safety Measures
12 before fueling and igniting safety measures only use j.A. Roby fuel with this fireplace • never use water to extinguish fuel box. • use thermal gloves to handle the device. • keep fire extinguishing device (a-b-c type) close to the fireplace. • to respect regulations, the fireplace should always ...
Page 13: Burner Installation
13 1. Remove the window by pulling up. 3. Install the closing device by inserting the hook on the cover in the hole of the handle. (see detail a) 5. Put the window back on his place like shown in page 9. Burner installation 2. Insert the backflow protection tray in the fireplace, and then insert the...
Page 14: Refill
14 refill • always position the burner so that the flames move towards the back of the fireplace, never to the glass. • pour the ethanol carefully • never pour fuel into a burning flame or hot burner. • always wait a minimum of 15 minutes to let the burner cool down before refilling. • do not exceed...
Page 15: Starting Up
15 • 1-let the lid in the open position like the picture • 2-once you have measured the liquid ethanol (maximum capacity 1100 ml), use the funnel to pour the liquid in the supply hole. • never fill over the bottom of the square hole (see detail c in the picture) • 3-wash your hands and every object ...
Page 16: Extinguish
16 extinguish • never use water to extinguish the fire. • if possible, let the fuel burn out completely as this will prevent the alcohol left in the burner to create a deflagration when re-igniting. • to extinguish the fire before the fuel has burned out, simply pull on the handle of the closing lid...
Page 17: Guide
17 ethanol fireplaces installation guide volcan b12 – trident (check the distance from center to center mounting holes before installation) to install figure a 1 tool required:measuring tape, level, pencil, eraser, square #2 tip screwdriver, 6 screws of 1 1/2 inch and 4 anchors 2 mark the starting p...
Page 18
18 volcan b12 – vesuve (check the distance from center to center mounting holes before installation) 1 tool required:measuring tape, level, pencil, eraser, square tip #2 screwdriver, 5 screws of 1½ inches and 3 anchors. 2 mark the starting point (see figure b) in the corner using the pencil and meas...
Page 19
19 volcan b12 - laguna (check the distance from center to center mounting holes before installation) figure c 1 tool required:measuring tape, level, pencil, eraser, square tip #2 screwdriver, 6 screws of 1½ inches and 4 anchors. 2 mark the starting point (see figure c) using the pencil and measuring...
Page 20
20 volcan b12 - kilauea important: starting point is located at the bottom of the fireplace figure d 1 tools required: reciprocating saw, measuring tape, level, pencil, eraser, square tip #2 screwdriver, 4 screws of 1 ½ inches and 4 anchors 2 mark the starting point (see figure d) using the pencil a...
Page 21
21 part to add with kilauea fireplace add the part on the holding tank. Hook the part on the edge of the backflow retention tray..
Page 22
22 volcan b12- taal warning note: taal fireplace can only be installed in the hearth of an operational and existing gas or wood burning fireplace. 1 tool required:drill,measuring tape, level, pencil, eraser, square tip #2 screwdriver, 6 screws of 1½ inches and 4 anchors. 3 from the starting point, d...
Page 23
23 volcan b12- fogo (check the distance from center to center mounting holes before installation) 1 tools required: reciprocating saw, measuring tape, level, pencil, eraser, square tip #2 screwdriver, 6 screws of 1 ½ inches and 4 anchors 2 mark the starting point (see figure g) using the pencil and ...
Page 24
24 figure g.
Page 25: Warranty
25 warranty j.A. Roby guarantees the ethanol fireplaces for one year only. The warranty of the manufacturer extends only to the original purchaser and is not transferable. The present warranty covers brand new products only, which have not been altered, modified nor repaired from moment of shipping ...