Jasco 45130 User Manual - Fcc Warning

Manual is about: Jasco Choice Alert 45130 Sensors: User Guide

Page of 16

Download

Print this page

Bookmark us

FCC Warning

Any unauthorized changes or modifications to the equipment

would void the user’s warranty and may conflict with both

state and federal laws. The Choice Alert system complies with

part 15 of the FCC rules. Operation is subject to the following

conditions:

1) The Choice Alert system may not cause

harmful interference.

) The Choice Alert system may accept any interference

received including interference that may cause

undesired operation.

NOTE: This equipment has been tested and found to

comply with the limits for a Class B digital device, pursuant to

Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a

residential installation. This equipment generates, uses and

can radiate radio frequency energy and, if not installed and

used in accordance with the instructions, may cause harmful

interference to radio communications. However, there is no

guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful

interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more

of the following measures:

– Reorient or relocate the receiving antenna.

– Increase the separation between the equipment

and receiver.

– Connect the equipment into an outlet on a circuit

different from that to which the receiver

is connected.

– Consult the dealer or an

experienced radio/TV technician for help

« ‹ Prev 10 11 12 13 14 15 16 Next › »

Summary of 45130

Page 1
45130 choice alert choice alert ™ control all sensors & accessories from one location ™ wireless alarm system garage door sensor user’s manual.
Page 2: 7-8
Important safeguards 4 introduction 5 installation 6 assigning a sensor to a zone 7-8 erasing a sensor from a zone 8-9 testing a sensor or your system 9-10 low battery indicator 10 battery warnings 11 f.A.Q.'s 1-1 fcc warning 14 table of contents.
Page 3: Congratulations
Before connecting or operating the garage door sensor, please read these instructions carefully and save this manual for future reference. Congratulations the ge choice alert ™ wireless alarm system is one of the most affordable and expandable wireless alarm systems available. You’ll discover that t...
Page 4: Important Safeguards
4 5 important safeguards precautions 1. Do not attempt to disassemble the garage door sensor, unless described in the user’s manual. There are no user serviceable parts. . Handle with care – avoid striking or shaking. Improper use or storage could damage the garage door sensor. Modifying or tamperin...
Page 5: Introduction
4 5 introduction the garage door sensor is designed to be used specifically with vertical opening garage or shed doors. When mounted properly it monitors when the door is open or closed. If the door is opened, the garage door sensor will transmit a signal to the control center. The settings on the c...
Page 6: Closed
6 7 preparing the garage door sensor for installation the garage door sensor is a self-contained sensor. Before installing open the battery door and, remove the yellow battery isolation tape from the garage door sensor. This activates the lithium battery inside the garage door sensor. The approximat...
Page 7: With Tape
6 7 bottom edge of the garage door sensor even with the door edge. In most applications you can use double sided tape (included). It is strongly suggested to mount garage door sensor lightly to ensure operation. Once you are confident with the mounting position apply pressure to secure to surface. F...
Page 8: 1 2 3 4
8 9 follow these steps to assign a sensor to a zone. Step 1 – press and hold the learn button on the control center for three seconds. When the control center sounds a long beep, release the learn button. Step 2 – press the zone button (1, 2, 3 or 4) for the zone you want to assign to the garage doo...
Page 9: - The System Is Armed.
8 9 learn button on the control center. The unit will beep once. Step 2 - while holding the learn button, press and hold the zone button to be erased. After five seconds the control center will sound two beeps and the zone led indicator will flash twice. Step 3 - release all buttons. The zone has be...
Page 10: Low Battery Indicator
10 11 note: the sensor has a led that flashes to show when the sensor has triggered and transmitted to the main unit. Step 4 - when testing is complete, unplug the ac adapter, then plug the ac adapter back in and reinstall batteries. This returns the control center to standard operation mode. Note: ...
Page 11: Warning!
10 11 note: the sensor detection system is ‘range dependant’, which means sensors located closer to the control center may seem to have batteries that last longer than those sensors at a greater distance. The lithium cell battery in the garage door sensor can last up to two years. Warning! Risk of p...
Page 12
1 1 garage door sensor f.A.Q.’s q. I bought a new sensor and the control center will not recognize it. Why? A. First, make sure that the yellow battery isolation tape has been removed and that the battery is new. Second, ensure the battery is inserted into the sensor according to polarity(+/-) marki...
Page 13
1 1 q. Why does one of my zones continually flash? A. This can be caused by 1 of 2 conditions. First condition, if it is a rapid flash it means a sensor in the zone has a low battery. If more than one sensor is in a zone, you will need to test each sensor by putting the unit into test mode (see pg. ...
Page 14: Fcc Warning
14 15 fcc warning any unauthorized changes or modifications to the equipment would void the user’s warranty and may conflict with both state and federal laws. The choice alert system complies with part 15 of the fcc rules. Operation is subject to the following conditions: 1) the choice alert system ...
Page 15: Warning
14 15 warning limitations of alarm products this product should be tested periodically to make sure it is working properly. The product, if used properly, may reduce the risk of burglary, robbery, or other adverse events. However, jasco is not an insurer, this product is neither insurance nor a guar...
Page 16
Is a trademark of the general electric company and is used under license to jasco products company llc, 10 e. Memorial road, oklahoma city, ok 73114. This jasco product comes with a 1 year limited warranty. Visit www.Jascoproducts.Com for details. 45130-1 01/09/08.