Jasco GE SmartHome Remote Manual

• Individual Z-Wave devices

• Groups

• Lighting scenes

Groups can include

up to 232 devices

Scenes can include

up to 32 devices

18

Compatible with all Z-WAVE products.

Remote Manual

Wireless Lighting Control

45600

INTRODUCTION

Thank you for purchasing the GE SmartHome

™

 Remote.  Your home control 

network can include up to 232 Z-Wave enabled devices.  This remote allows you 

to control up to 18 individual Z-Wave devices with one easy-to-use, compact unit.  

You can also set up and control up to 18 groups of lights as well as 18 scenes for 

task or mood lighting.  Each group can include up to 232 Z-Wave devices and 

each scene can include up to 32 Z-Wave devices.  Lights can be included in 

multiple groups.  Scenes can include lights from different groups.  

Please note: 

The terms “Device”, “Node” and “Light” all refer to an individual 

Z-Wave enabled device in your home control network and are interchangeable 

within the context of these instructions.

If this remote is used as the primary controller, you must use it to create your 

control network.  You can use multiple remote controls with your Z-Wave lighting 

control network, however, only one remote will act as the primary controller.  The 

primary controller must be used to add or delete devices (lights / nodes) from your 

network.  All other remotes are considered secondary and can be used to create 

groups and/or scenes and control your lighting however secondary remotes 

cannot add or delete devices from your control network. 

NOTE: This product can be operated in one Z-Wave network with Z-Wave certified devices 

from other manufacturers and/or other applications. The different listening nodes within 

the network can act as repeaters regardless of vendor.

For best results, please read and perform all the remaining instructions before 

using the remote.  Keep this guide for future reference. 

INSTALLING BATTERIES

Three “AAA” Alkaline batteries (not included) are required.

receives information from the remote.

6. When the green LED blinks twice, you have successfully added the device to 

your home network.

7.  The device can now be added to Groups and/or Scenes.

NOTE: If the red LED emits one long, steady blink, you have pressed an invalid key 

or the device has not been successfully added to your home network.  Please 

make sure the remote is within two feet of the device and try again.

ADDING A LIGHT (DEVICE / NODE) TO YOUR REMOTE

You can add a maximum of 18 lights to your remote so that they can be 

controlled individually.  Adding a device to your remote also adds it to your 

network.  If the device number you are trying to add is already associated with 

another device, the previous information is lost. 

To add a device to your remote, perform the following steps:

1. Press and hold SETUP until both the red and green LEDs blink twice.

2. Press ADD once.  (Red LED blinks once)

3. Press LIGHT once.  (Red LED blinks once)

4. Press a digit (1-9) for the device location you wish to add.  Press SHIFT and the 

digit (1-9) if you are adding devices 10 through 18. (Green LED 

blinks rapidly)

5. Press the button on the device so that it sends its information to the remote 

and receives information from the remote.

6. When the green LED blinks twice, you have successfully added the device to 

your remote control.

NOTE: If the red LED emits one long, steady blink, you have pressed an invalid key or the 

device has not been successfully added to your remote.  Please make sure the remote is 

within two feet of the device and try again.

REMOVING AN INDIVIDUAL DEVICE (LIGHT / NODE) FROM YOUR REMOTE 

1. Press and hold SETUP until both the red and green LEDs blink twice.

2. Press REMOVE once.   (Red LED blinks once)

3. Press LIGHT once.  (Red LED blinks once)

4. Press a digit (1-9) for the device location you wish to remove. Press SHIFT and 

the digit (1-9) if you are removing devices 10 through 18.

5. When the green LED blinks twice, you have successfully removed the device 

• To dim the light, press and hold the OFF key for more than one second. (Green 

LED blinks rapidly)

NOTE: If the red LED emits one long, steady blink the remote has not successfully 

communicated with the device. Repeat steps 1-2 if this occurs.

SETTING UP AND CONTROLLING A GROUP

You can create a collection of devices (lights / nodes) that you can control as a 

group.  You can set up a maximum of 18 groups.  Each group can contain up to 

232 devices. 

Adding a Device (Light / Node) to a Group

To add a device to a group, perform the following steps:

1. Press and hold SETUP until both the red and green LEDs blink twice.

2. Press ADD once. (Red LED blinks once)

3. Press GROUP once. (Red LED blinks once)

4. Press a digit (1-9) for the group you wish to add the device to. Press SHIFT and 

the digit (1-9) if you are adding a devices to groups 10 through 18. (Green LED 

blinks rapidly)

5. Press the button on the device so that it sends its information to the remote and 

receives information from the remote.

6. When the green LED blinks twice, you have successfully added the device to 

your group.

NOTE: If the red LED emits one long, steady blink, you have pressed an invalid key or the 

device has not been successfully added to your group. Repeat steps 1-6 if this occurs.

Removing a Device (Light / Node) from a Group

1. Press and hold SETUP until both the red and green LEDs blink twice.

2. Press REMOVE once. (Red LED blinks once)

3. Press GROUP once. (Red LED blinks once)

4. Press a digit (1-9) for the group you wish to remove the device from. Press SHIFT 

and the digit (1-9) if you are removing a device from groups 10 through 18. 

(Green LED blinks rapidly)

5. Press the button on the device you wish to remove.

6. When the green LED blinks twice, you have successfully removed the device 

from your group.

NOTE: If the red LED emits one long, steady blink, you have pressed an invalid key or the 

device has not been successfully removed from your group. Repeat steps 1-6 if this occurs.

Deleting a Group

1. Press and hold SETUP until both the red and green LEDs blink twice.

2. Press DELETE once. (Red LED blinks once)

3. Press GROUP once. (Red LED blinks once)

4. Press a digit (1-9) for the group you wish to delete.  Press Shift and the digit (1-9) 

if you are deleting groups 10 through 18.

5. When the green LED blinks twice, you have successfully deleted the group from 

your home network.

NOTE: If the red LED emits one long, steady blink, you have pressed an invalid key or the group 

has not been successfully removed from your home network. Repeat steps 1-5 if this occurs.

Controlling a Group

To control a Group, perform the following steps:

1. Press GROUP once to put the remote into “GROUP Control” mode.  (Red LED 

blinks once) The remote will stay in this mode until either the Light or Scene 

mode is activated.

2. Press the digit key for the group you wish to control (1-9). Press SHIFT and the 

digit (1-9) if you are controlling groups 10 through 18. The green LED will 

blink once.

NOTE: If the red LED emits one long, steady blink, the remote has not successfully 

communicated with the devices in the group. Repeat steps 1-2 if this occurs.

SETTING UP SCENES

A scene is a single device or group of devices that can be preset to turn to a 

previously specified setting (for example, brightness level). Scenes are ideal for 

task or mood lighting.  You can set up a maximum of 18 scenes, containing up to 

32 devices per scene. Scenes can include lights from different groups.

Adding a Light (Device / Node) to a Scene

1. Press and hold SETUP until both the red and green LEDs blink twice.

2. Press ADD once. (Red LED blinks once)

3. Press SCENE once. (Red LED blinks once)

4. Press a digit (1-9) for the scene you wish to add the device to. Press SHIFT and 

the digit (1-9) if you are adding devices to scenes 10 through 18. (Green LED 

blinks rapidly)

5. Press the button on the light you are adding.  (Green LED pauses briefly, blinks 

once and then resumes blinking rapidly, indicating that the remote is pending 

the setup of the bright/dim setting on the device.)

6. Adjust the brightness level on the device within 30 seconds (refer to the manual 

for the device)

7. Press SCENE. The green LED stops blinking.

8. When the green LED blinks twice, you have successfully added the device to a 

scene.

NOTE: If the red LED emits one long, steady blink, you have pressed an invalid key or the 

device has not been successfully added to the scene. Repeat steps 1-7 if this occurs.

Removing a Light (Device / Node) from a Scene

1. Press and hold SETUP until both the red and green LEDs blink twice.

2. Press REMOVE once. (Red LED blinks once)

3. Press SCENE once. (Red LED blinks once)

4. Press a digit (1-9) for the scene you wish to remove the device from.  Press SHIFT 

and the digit (1-9) if you are removing devices from scenes 10 through 18.             

(Green LED blinks rapidly)

5. Press the button on the device that you wish to remove.

6. When the green LED blinks twice, you have successfully removed the device 

from the scene.

NOTE: If the red LED emits one long, steady blink, you have pressed an invalid key or the 

device has not been successfully removed from the scene. Repeat steps 1-6 if this occurs.

Deleting a Scene

1. Press and hold SETUP until both the red and green LEDs blink twice.

2. Press DELETE once. (Red LED blinks once)

3. Press SCENE once. (Red LED blinks once)

4. Press a digit (1-9) for the scene you wish to delete.  Press SHIFT and the digit 

(1-9) if you are deleting scenes 10 through 18.

5. When the green LED blinks twice, you have successfully deleted the scene from 

your home network.

NOTE: If the red LED emits one long, steady blink, you have pressed an invalid key or the 

scene has not been successfully deleted. Repeat steps 1-5 if this occurs

from your remote control.

NOTE: If the red LED emits one long, steady blink, you have pressed an invalid key or the device 

has not been successfully removed from your remote control. Repeat steps 1-5 if this occurs.

DELETING A DEVICE (LIGHT / NODE) FROM YOUR NETWORK

To reset a device to its factory default, you must delete it from the network. To 

delete the device from your network, perform the following steps:

1. Press and hold SETUP until both the red and green LEDs blink twice.

2. Press DELETE once. (Red LED blinks once)

3. Press LIGHT once. (Green LED blinks rapidly)

4. Press and release the button on the device so that it sends its information to the 

remote and receives information from the remote.

5. When the green LED blinks twice, you have successfully deleted the device from 

your home network.

NOTE: If the red LED emits one long, steady blink, you have pressed an invalid key or the device 

has not been successfully deleted from your home network. Repeat steps 1-5 if this occurs.

CONTROLLING INDIVIDUAL LIGHTS (DEVICES / NODES)

You can control a light to turn on or off, or change its brightness level. The 

operation of a specific device varies by product. Refer to the manual for that 

device to learn its specific operation. 

1. Press and release the LIGHT key to put the remote into “Individual Light Control” 

mode.  (Red LED blinks once) The remote will stay in this mode until either the 

Group or Scene mode is activated.

2. Select the light you want to control.  

(Press and release SHIFT to control lights 10 through 18.)

Turning a Light On or Off  

• To turn a light on, press and release the ON key for less than one second. The 

green LED will blink once.

• To turn a light off, press and release the OFF key for less than one second. The 

green LED will blink once.

Setting a Light’s Brightness Level

• To make a light brighter, press and hold the ON key for more than one second. 

(Green LED blinks rapidly)

CAUTION 

Battery Use And Safety

• Use only fresh batteries of the required size and recommended type.

• Do not mix old and new batteries or different types of batteries.

• If you do not plan to use the remote for an extended period, remove the batteries. 

They can leak chemicals that can destroy electronic parts.

• Dispose of old batteries promptly and properly. Do not burn or bury them. 

To Install Batteries:

1. Open the battery compartment cover (located on the back of the remote). 

2. Note the + and - polarity symbols inside the battery compartment. 

3. Insert the batteries, making sure their polarity matches the symbols in the 

compartment. 

4. Replace the cover. 

NOTE: When the red LED blinks 5 times after a key press, you must replace the 

batteries.  The remote retains all its user settings while replacing the batteries.

NOT FOR USE WITH MEDICAL OR LIFE SUPPORT EQUIPMENT

Z-Wave enabled devices should never be used to supply power to, or control

the On/Off status of medical and/or life support equipment

NOTES ON NETWORK MANAGEMENT:

Add a node, group or scene can also be referred to as include a node, group 

or scene. Remove a node, group or scene can also be referred to as Exclude a node, 

group or scene.

ADDING A DEVICE (NODE / LIGHT) TO THE NETWORK

In order to control the lights, they must be Z-wave enabled and you must first add 

them to your home network.  To add a device to your home network without assigning 

it to a specific number key, perform the following steps: 

1. Press and hold SETUP until both the red and green LEDs blink twice.

2. Press ADD once. (Red LED blinks once)

3. Press LIGHT once. (Red LED blinks once)

4. Press LIGHT again. (Green LED blinks rapidly)

5. Press the button on the device so that it sends its information to the remote and 

1

2

3

4

5

6

7