1. DL manuals
  2. Jasco
  3. Control Unit
  4. Z-Wave Auxiliary Switch
  5. User manual

Jasco Z-Wave Auxiliary Switch User manual

Manual is about: Z-Wave® Certified Wireless Lighting Control

Summary of Z-Wave Auxiliary Switch

  • Page 1

    Z-wave ® certified wireless lighting control auxiliary switch 45710 zw2004 made in china.

  • Page 2

    This auxiliary switch is a component of the jasco z-wave ® lighting control system and is designed to work with all jasco branded z-wave dimmer and on/ off switches. Use one auxiliary switch for 3-way control such as the top and bottom of a staircase (1 load/light & 2 switches) with one of the above...

  • Page 3: Controlling Appliances:

    This device is intended for installation in accordance with the national electric code and local regulations in the united states, or the canadian electrical code and local regulations in canada. If you are unsure or uncomfortable about performing this installation consult a qualified electrician. R...

  • Page 4: Equipment

    Continued for these reasons, we recommend the following: 1. Assign z-wave controlled appliances to device numbers 10 – 18 on the jasco remote. The likelihood of unintentionally turning on the appliance will be reduced significantly because the “shift” button will need to be pressed before pressing d...

  • Page 5

    Important note about 3-way circuits the term “3-way circuit” refers to a circuit with two switches and one load (light) like you find at the top and bottom of a stairway. There are many ways to physically wire a 3-way circuit and it is important to understand how the circuit you wish to upgrade to z...

  • Page 6: Typical 3-Way Circuit:

    Typical 3-way circuit: black (line / hot) black (line / hot) white white (neutral) black (load) white z-wave 45710 z-wave on/off or dimmer switch colored (not green) black black black white switch 1 switch 2.

  • Page 7

    Correct z-wave switch position for typical 3-way circuit: please consult an electrician if you have trouble identifying the type of wiring circuit you wish to convert or if you do not feel confident in your ability to convert the circuit to z-wave control. White (neutral) z-wave black (line / hot) b...

  • Page 8

    To change color of the switch 1. Push side tabs in on one side and then the other to release cover. Lift the cover up and off. 2. Simply put the new cover onto the switch by inserting the air gap and side tabs and snapping securly into place. 1..

  • Page 9: Installation

    Installation this switch may be used in new installations or to replace an existing wall switch when converting a 3 or 4 way circuit to z-wave. It can not be used by itself for 2-way control (one switch & one load). Please note: the auxiliary switch(s) must be wired to the same neutral as the z-wave...

  • Page 10: 45709, 45712 Or 45715

    4-way wiring schematic using two 45710’s and one 45709, 45712 or 45715 shock hazard! Turn off the power to the branch circuit for the switch and lighting fixture at the service panel. All wiring connections must be made with the power off to avoid personal injury and/or damage to the switch. Travele...

  • Page 11: Z-Wave 45709, 45712 Or 45715

    Z-wave 45709, 45712 or 45715 1.Shut off power to the circuit at fuse box or circuit breaker. 2. Remove wall plate. ! Warning: verify power is off to switch box before continuing. 3. Remove the switch mounting screws. 4. Carefully remove the switch from the switch box. Do not disconnect the wires. 5....

  • Page 12

    Service panel (hot) to the lead or terminal marked line. 11. Connect the traveler wire (usually red) to the wire or screw terminal marked traveler. The other end of this traveler wire connects to the traveler wire on the 45710 auxiliary switch. The traveler terminal or lead must be insulated if you ...

  • Page 13

    2. Do not connect the 45710 auxiliary switch to the home’s black hot (line) wire. Observe important wiring information important: this switch is rated for and intended to only be used with copper wire. The home’s electrical wires may be attached to the screw terminals or inserted into the holes in t...

  • Page 14: Operation

    Operation when installed with the 45712 or 45715 dimmer: • press and release the top of the 45710’s rocker to turn the connected lighting on and return the brightness level to its previous setting. • press and hold the top of the 45710’s rocker to turn the connected lighting on and set the brightnes...

  • Page 15: Warranty

    Warranty jasco products warrants this product to be free from manufacturing defects for a period of two years from the original date of consumer purchase. This warranty is limited to the repair or replacement of this product only and does not extend to consequential or incidental damage to other pro...

  • Page 16: Specifications

    Zw3005 can ices-3(b) / nmb-3(b) this device complies with industry canada license-exempt rss standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesire...

  • Page 17

    Distributed by jasco products company llc, 10 e. Memorial road, oklahoma city, oklahoma 73114. Specifications subject to change without notice due to continuing product improvement z-wave is a registered us trademark of sigma designs © 2013 jasco products 45710 zw2004 rev. 08/22/13.