- DL manuals
- Jasic
- Welding System
- Arc JA-140
- Operator's Manual
Jasic Arc JA-140 Operator's Manual
Summary of Arc JA-140
Page 1
Wilkinsonstar.Com arc series dc mma / lift tig welding machines order codes !Ja-140, ja-160, ja-180, ja-200 ! ! ! ! Ja-160dv, ja-180dv - dual voltage operator manual.
Page 2: Your New Product
Your new product thank you for selecting this jasic technology, wilkinson star product. This product manual has been designed to ensure that you get the most from your new product. Please ensure that you are fully conversant with the information provided paying particular attention to the safety pre...
Page 3: Safety Precautions
Safety precautions 1 these general safety norms cover both arc welding machines and plasma cutting machines unless otherwise noted. The equipment must only be used for the purpose it was designed for. Using it in any other way could result in damage or injury and in breach of the safety rules. Only ...
Page 4
Do not weld on coated metals, unless the coating is removed from the weld area, the area is well ventilated, and while wearing an air-supplied respirator. The coatings on many metals can give off toxic fumes if welded. Prevention against burns and radiation arc rays from the welding process produce i...
Page 5
Rf declaration equipment that complies with directive 2004/108/ec concerning electromagnetic compatibility (emc) and the technical requirements of en60974-10 is designed for use in industrial buildings and not those for domestic use where electricity is provided via the low voltage public distributi...
Page 6: Product Overview
Product overview 2 the unique electronic structure and air channel design in this series of machines provides efficient cooling of the power devices as well as improving the duty cycles of the machines. The design of the forced air-cooling system channel can effectively prevent the power devices and co...
Page 7: Technical Data
Technical data 3 single voltage units tested at the environment temperature of 40 0 c product design may vary due to customer requirements. 6 technical parameter technical parameter unit model model model model arc140 (ja-140) arc160 (ja-160) arc180 (ja-180) arc200 (ja-200) rated input voltage rated...
Page 8
Dual voltage units technical parameter technical parameter unit model model model model arc160dv (ja-160dv) arc160dv (ja-160dv) arc180dv (ja-180dv) arc180dv (ja-180dv) rated input voltage rated input voltage v ac230v±15% 50/60hz ac110v±15% 50/60hz ac230v±15% 50/60hz ac115v±15% 50/60hz rated input po...
Page 9: Controls
Controls 4 front view 1. Overheating led: overheating led on indicates that the temperature inside the machine is too high and the machine is under overheating protection status. 2. Power led: power led on indicates that the power switch of the machine is on. 3. Mma/tig switch: to toggle between mma...
Page 10: Installation
Installation 5 unpacking check the packaging for any signs of damage. Carefully remove the machine and retain the packaging until the installation is complete. Location the machine should be located in a suitable position and environment. Care should be taken to avoid moisture, dust, steam, oil or c...
Page 11: Operation
Operation before starting any welding activity ensure that you have suitable eye protection and protective clothing. Also take the necessary steps to protect any persons within the area. Mma after connecting the welding leads as detailed you will need to switch the power switch on the back panel to ...
Page 12
Maintenance and troubleshooting 6 the following operation requires sufficient professional knowledge on electric aspects and comprehensive safety knowledge. Make sure the input cable of the machine is disconnected from the electricity supply and wait for 5 minutes before removing the machine covers. I...
Page 13: Electrical Schematic
Electrical schematic 7 12 schematic for single voltage unit schematic for dual voltage unit.
Page 14: Parts List
Parts list 8 arc pro 140 - (ja-140) 13 no. Part no description no. Part no description 1 10004957 power switch 15 10037859 thermal switch 2 10037125 back panel 16 10037135 driver transformer 3 10044817 fan 17 10006282 irf9z24n 4 10043477 handle 18 10006282 irfz24n 5 10043689 louver 19 10037134 switc...
Page 15
Arc pro 160 - (ja-160dv) 14 no. Part no description no. Part no description 1 10004957 power switch 15 10037859 thermal switch 2 10037125 back panel 16 10037135 drive transformer 3 10044817 fan 17 10006282 irf9z24n 4 10043477 handle 18 10006282 irfz24n 5 10043689 louver 19 10037134 switching mode po...
Page 16
Arc pro 180 - (ja-180dv) no. Part no description no. Part no description 1 10004957 power switch 15 10037852 thermal switch 2 10037837 back panel 16 10037135 driver transformer 3 10044009 fan 17 10006282 irf9z24n 4 10043477 handle 18 10006282 irfz24n 5 10043689 louver 19 10037134 switching mode powe...
Page 17
Arc pro 200 - (ja-200) 16 no. Part no description no. Part no description 1 10004957 power switch 15 10037852 thermal switch 2 10037837 back panel 16 10037135 drive transformer 3 10044009 fan 17 10006282 irf9z24n 4 10043477 handle 18 10006282 irfz24n 5 10043689 louver 19 10037134 switching mode powe...
Page 18
17.
Page 19
Ja arc series dc tig/mma welding machine order code ! Ja-140, ja-160, ja-180, ja-200 ! ! ! ! Ja-160dv, ja-180dv - dual voltage © wilkinson star limited issue 1 january 2014 product is subject to change without notice xviii.