- DL manuals
- Jasic
- Welding System
- ARC400
- Operator's Manual
Jasic ARC400 Operator's Manual
Summary of ARC400
Page 1
Wilkinsonstar.Com arc 400 dc mma / lift tig welding machines order code ! Ja-400 operator manual.
Page 2: Your New Product
Your new product thank you for selecting this jasic technology, wilkinson star product. This product manual has been designed to ensure that you get the most from your new product. Please ensure that you are fully conversant with the information provided paying particular attention to the safety pre...
Page 3: Safety Precautions
Safety precautions 1 these general safety norms cover both arc welding machines and plasma cutting machines unless otherwise noted. The equipment must only be used for the purpose it was designed for. Using it in any other way could result in damage or injury and in breach of the safety rules. Only ...
Page 4
Do not weld on coated metals, unless the coating is removed from the weld area, the area is well ventilated, and while wearing an air-supplied respirator. The coatings on many metals can give off toxic fumes if welded. Prevention against burns and radiation arc rays from the welding process produce i...
Page 5
Rf declaration equipment that complies with directive 2004/108/ec concerning electromagnetic compatibility (emc) and the technical requirements of en60974-10 is designed for use in industrial buildings and not those for domestic use where electricity is provided via the low voltage public distributi...
Page 6: Product Overview
Product overview 2 the unique electronic structure and air channel design in this series of machines provides efficient cooling of the power devices as well as improving the duty cycles of the machines. The design of the forced air-cooling system channel can effectively prevent the power devices and co...
Page 7: Technical Data
Technical data 3 model arc400 arc500 arc630 input voltage range (v) 400v±15﹪ 50/60hz 400v±15﹪ 50/60hz 400v±15﹪ 50/60hz recommended fuse capacity (a) 40 60 60 rated output 400a/36v 500a/40v 630a/44v welding current range (a) 20~400 25~500 30~630 arc force current range (a) 20~200 20~200 20~200 no-loa...
Page 8: Controls
Controls 4 front view 1. Over current led 2. Low voltage led: led on indicates that the input voltage is low. 3. Digital ammeter. 4. Current control knob 5. Arc force control 6. "+" output terminal: to connect the electrode holder. 7. Remote control socket. 8. "-" output terminal: to connect the wor...
Page 9: Installation
Installation 5 unpacking check the packaging for any signs of damage. Carefully remove the machine and retain the packaging until the installation is complete. Location the machine should be located in a suitable position and environment. Care should be taken to avoid moisture, dust, steam, oil or c...
Page 10: Operation
Operation before starting any welding activity ensure that you have suitable eye protection and protective clothing. Also take the necessary steps to protect any persons within the area. Mma after connecting the welding leads as detailed you will need to switch the power switch on the back panel to ...
Page 11
Maintenance and troubleshooting 6 the following operation requires sufficient professional knowledge on electric aspects and comprehensive safety knowledge. Make sure the input cable of the machine is disconnected from the electricity supply and wait for 5 minutes before removing the machine covers. I...
Page 12
11 symptom cause solution difficult to ignite the arc the arc ignition current is too low or the arc ignition time is too short. Increase the arc ignition current or prolong the arc starting time. No arc can be started phase failure of the mains power supply or the mains supply cable is not connecte...
Page 13: Electrical Schematic
Electrical schematic 7 12.
Page 14: Parts List
Parts list 8 arc 400 - (ja-400) 13 41 36 35 34 37 38 39 40 33 32 31 30 29 28 3 4 5 6 7 8 10 11 12 13 14 23 22 24 25 26 27 20 19 18 17 21 2 1 9 15 16.
Page 15
14 no. Part no description no. Part no description 1 10027491 the handle 22 10013609 wind deflector 2 10043860 machine cover 23 10016137 corner pieces 3 10000650 main control board 24 10016274 the small radiator 4 10000716 power drive board 25 10016565 stand 5 10001707 cement resistor 26 10016273 th...
Page 16: Order Code ! Ja-400
Ja arc 400 dc tig/mma welding machine order code ! Ja-400 © wilkinson star limited issue 1 january 2014 product is subject to change without notice xv.