1. DL manuals
  2. Jasic
  3. Welding System
  4. JM-160C
  5. Operator's Manual

Jasic JM-160C Operator's Manual

Manual is about: MIG Series

Summary of JM-160C

  • Page 1

    Wilkinsonstar.Com mig series mig/mag/mma compact welding machines order code ! Jm-160c,jm-175c, jm-180c, jm-200c operator manual.

  • Page 2: Your New Product

    Your new product thank you for selecting this jasic technology, wilkinson star product. This product manual has been designed to ensure that you get the most from your new product. Please ensure that you are fully conversant with the information provided paying particular attention to the safety pre...

  • Page 3: Safety Precautions

    Safety precautions 1 these general safety norms cover both arc welding machines and plasma cutting machines unless otherwise noted. The equipment must only be used for the purpose it was designed for. Using it in any other way could result in damage or injury and in breach of the safety rules. Only ...

  • Page 4

    Do not weld on coated metals, unless the coating is removed from the weld area, the area is well ventilated, and while wearing an air-supplied respirator. The coatings on many metals can give off toxic fumes if welded. Prevention against burns and radiation arc rays from the welding process produce i...

  • Page 5

    Rf declaration equipment that complies with directive 2004/108/ec concerning electromagnetic compatibility (emc) and the technical requirements of en60974-10 is designed for use in industrial buildings and not those for domestic use where electricity is provided via the low voltage public distributi...

  • Page 6: Product Overview

    Product overview 2 the unique electronic structure and air channel design in this series of machines provides efficient cooling of the power devices as well as improving the duty cycles of the machines. The design of the forced air-cooling system channel can effectively prevent the power devices and co...

  • Page 7: Technical Data

    Technical data 3 ① tested at the environment temperature of 40 0 c ② product design may vary due to customer requirements. 6 technical parameter unit model mig160 (jm-160c) mig175 (jm-175c) mig180 (jm-180c) mig200 (jm-200c) rated input voltage v ac230v±15% 50/60hz rated input power kva 7.1 7.9 8.2 9...

  • Page 8: Controls

    Controls 4 front view 1. Current control - mma 2. Power on led 3. Overheat led 4. Voltage control - mig 5. Wire speed control - mig 6. Mig / mag switch 7. Gas /no gas selector 8. Push pull control socket 9. “+” output terminal 10. Euro torch connector - mig 11. “+” output terminal rear view 12. Inpu...

  • Page 9

    15 handle 16 push pull torch selector 17 burn back control 18 wire inch button 19 wire feed assembly socket 1 push pull torch power “+” socket 2 push pull torch power “-” socket 3-9 null 8.

  • Page 10: Installation

    Installation 5 unpacking check the packaging for any signs of damage. Carefully remove the machine and retain the packaging until the installation is complete. Location the machine should be located in a suitable position and environment. Care should be taken to avoid moisture, dust, steam, oil or c...

  • Page 11

    Feeding position on the drive roll matches the contact tip size of the welding torch and the wire size being used. Release the pressure arm of the wire feeder to thread the wire through the guide tube, and into the drive roll groove. Adjust the pressure arm, ensuring no sliding of the wire. Too high...

  • Page 12: Operation

    Operation before starting any welding activity ensure that you have suitable eye protection and protective clothing. Also take the necessary steps to protect any persons within the area. Mma after connecting the welding leads as detailed you will need to switch the power switch on the back panel to ...

  • Page 13

    Maintenance and troubleshooting 6 the following operation requires sufficient professional knowledge on electric aspects and comprehensive safety knowledge. Make sure the input cable of the machine is disconnected from the electricity supply and wait for 5 minutes before removing the machine covers. I...

  • Page 14: Electrical Schematic

    Electrical schematic 7 13.

  • Page 15: Parts List

    Parts list 8 jm-160c 14 1 2 14 15 16 18 19 20 21 6 5 13 22 4 7 8 12 11 10 9 17 23 24 3.

  • Page 16

    Jm-200c 15 no. Part no description no. Part no description 1 10044511 main board 13 10041449 spool for wire feeder 2 10041446 fan 14 10044510 control board 3 10044512 silicon bridge board 15 10041421 wire feeder and line 4 10041723 gas nozzle 16 10041707 fixing plate for control board 5 10041721 sil...

  • Page 17

    No. Part no description no. Part no description 1 10043884 main board 13 10041449 spool for wire feeder 2 10041446 fan 14 10043885 control board 3 10041412 silicon bridge board 15 10041421 wire feeder and line 4 10041723 gas nozzle 16 10041707 fixing plate for control board 5 10041721 silicon bridge...

  • Page 18

    Jm mig series mig/mag/mma welding machine order code ! Jm-160c (mig 160) jm-200c (mig 200) © wilkinson star limited issue 1 january 2014 product is subject to change without notice xvii.