Summary of JP-25C
Page 1
Wilkinsonstar.Com plasma 25c air plasma cutting machine order code ! Jp-25c operator manual.
Page 2: Your New Product
Your new product thank you for selecting this jasic technology, wilkinson star product. This product manual has been designed to ensure that you get the most from your new product. Please ensure that you are fully conversant with the information provided paying particular attention to the safety pre...
Page 3: Safety Precautions
Safety precautions 1 these general safety norms cover both arc welding machines and plasma cutting machines unless otherwise noted. The equipment must only be used for the purpose it was designed for. Using it in any other way could result in damage or injury and in breach of the safety rules. Only ...
Page 4
Do not weld on coated metals, unless the coating is removed from the weld area, the area is well ventilated, and while wearing an air-supplied respirator. The coatings on many metals can give off toxic fumes if welded. Prevention against burns and radiation arc rays from the welding process produce i...
Page 5
Rf declaration equipment that complies with directive 2004/108/ec concerning electromagnetic compatibility (emc) and the technical requirements of en60974-10 is designed for use in industrial buildings and not those for domestic use where electricity is provided via the low voltage public distributi...
Page 6: Product Overview
Product overview 2 cut25 is a plasma cutting machine model developed from the original cut series plasma cutting machines. It inherits the mature and stable inverter technology of cut series: with pwm technology and high-power mosfet switching devices, it converts the dc voltage, which is rectified ...
Page 7: Technical Data
Technical data 3 tested at the environment temperature of 40 0 c product design may vary due to customer requirements. 6 model cut25 rated input voltage (v) 230v ac±10% rated input frequency (hz) 50/60 rated input capacity (kva) 3.5 no-load voltage (v) 230±15 cutting current (a) 25 rated output volt...
Page 8
Cutting speed guide cutting speed {m/mm) 7 cutting thickness (mm) 1 2 3 4 5 6 8 mild steel 7 1.4 0.3 0.2 galvanised 7 1.4 0.3 0.2 stainless steel 7 1.4 0.3 0.2 aluminium 5 1.2 0.2 brass 0.7 0.2 copper 0.7 0.2.
Page 9: Controls
Controls 4 1. Input cable 2. Work return cable socket 3. Torch connection. 4 mains switch- 5 power led - it indicates that the input power is normal. 6. Overheat led.- this indicator will turn on when the machine is overheated due to overload or over current and the output has been disabled. Leave t...
Page 10: Installation
Installation 5 unpacking check the packaging for any signs of damage. Carefully remove the machine and retain the packaging until the installation is complete. Location the machine should be located in a suitable position and environment. Care should be taken to avoid moisture, dust, steam, oil or c...
Page 11: Operation
Operation before starting any cutting activity ensure that you have suitable eye protection and protective clothing. Also take the necessary steps to protect any persons within the area. Check that all connections have been made as shown above check the following before starting the machine. 1) chec...
Page 12
Maintenance and troubleshooting 6 the following operation requires sufficient professional knowledge on electric aspects and comprehensive safety knowledge. Make sure the input cable of the machine is disconnected from the electricity supply and wait for 5 minutes before removing the machine covers. I...
Page 13: Electrical Schematic
Electrical schematic 7 12.
Page 14: Parts List
Parts list 8 cut 25 - (jp-25c) 13.
Page 15
14 no. Part no description no. Part no description 1 10027491 handle 13 10021916 spring line button 2 10046083 machine cover 14 10043261 air compressor 3 10046082 central insulation board 15 10046113 shock absorber 4 10001873 fan 16 10016489 foot 5 10046115 clamp 17 10046058 bottom panel 6 10020602 ...
Page 16: Order Code ! Jp-25C
Jp-25c air plasma cutting machine order code ! Jp-25c © wilkinson star limited issue 1 january 2014 product is subject to change without notice xv.