Summary of QC8626
Page 1
Mini ip dome camera user’s manual version 3.5.0
Page 2: Welcome
I welcome thank you for purchasing our ip camera! This user’s manual is designed to be a reference tool for your system. Please read the following safeguard and warnings carefully before you use this series product! Please keep this user’s manual well for future reference!.
Page 3
Ii important safeguards and warnings 1．electrical safety all installation and operation here should conform to your local electrical safety codes. The power shall conform to the requirement in the selv (safety extra low voltage) and the limited power source is rated 12v dc in the iec60950-1. We assu...
Page 4
Iii always use the dry soft cloth to clean the device. If there is too much dust, please use the water to dilute the mild detergent first and then use it to clean the device. Finally use the dry cloth to clean the device. Please put the dustproof cap to protect the ccd (cmos) component when you do n...
Page 5: Table of Contents
Iv table of contents 1 general introduction ..................................................................................................................1 1.1 overview........................................................................................................................1 1.2 fe...
Page 6
1 1general introduction 1.1overview this series ip camera integrates the traditional camera and network video technology. It adopts audio and video data collection, transmission together. It can connect to the network directly without any auxiliary device. This series ipc uses standard h.264 video c...
Page 7
2 z support video watermark function to avoid vicious video modification. 1.3specifications 1.3.1 performance please refer to the following sheet for ipc performance specification. Model parameter series main processor ti davinci high performance dsp os embedded linux system resources support real-t...
Page 8
3 video loss activation event: video storage, image snapshot, log, email smtp function and etc. Record priority manual> video detect>schedule record and backup local storage support micro sd card storage wire network 1-channel wire ethernet port, 10/100 base-t ethernet network protocol standard http...
Page 9
4 default setup function setup type item series resolution 1080p（1920*1080） frame rate （ fps） pal: 25 ntsc:30 bit stream type cbr reference bit rate 3584-6144 kb/s bit rate 8192 i frame interval 50 watermark settings enable watermark character digitalcctv enable enable bit stream type general encode...
Page 10
5 default setup function setup type item mac address depends on the device ip version ipv4 ip address 192.168.1.168 subnet mask 255.255.255.0 default gateway 192.168.1.1 preferred dns 8.8.8.8 alternate dns 8.8.8.8 enable arp/pingto to set ip address service enable max connection 10 tcp port 37777 ud...
Page 11
6 default setup function setup type item authenticati on (encrypt mode) n/a title (subject) ipc message attachment enable main receiver n/a interval 0s health email disable ，interval=60m upnp enable upnp disable snmp v1 disable snmp v2 disable snmp v3 disable snmp port 161 read community public writ...
Page 12
7 default setup function setup type item series record channel enable record delay 10 seconds send email disable snapshot disable enable no sd card send email enable capacity limit (space threshold) capacit y warnin g send email enable sd card error send email enable disable record enable disconnec ...
Page 13
8 default setup function setup type item series language english video standard ntsc date format y-m-d time format 24h time zone gmt+08:00 current time sync pc dst disable dts type week start time 00:00:00 of the first sunday of the month end time 00:00:00 of the second monday of the month synchroni...
Page 14
9 2framework 2.1dimensions please refer to the following figure for the dimension information. The unit is mm. See figure 2-1 through figure 2-3. Figure 2-1 figure 2-2.
Page 15
10 figure 2-3 2.2structure please refer to the following figure for detailed information. See figure 2-4. Figure 2-4 please refer to the following sheet for detailed information..
Page 16
11 sn name 1 x-y-z rotation module 2 device lens 3 dome camera enclosure sn name function 4 power input port connect to the dc 12+ power to input the power. 5 network port network data input, output and poe..
Page 17
12 3installation 3.1device installation this series ipc can be put on the table to realize surveillance. Or you can use the bracket or the in- ceiling installation to realize the hang function. Please refer to the steps listed below. Figure 3-1 figure 3-2 step1 use the inner hexagonal wrench (provid...
Page 18
13 the cable from the side port of the cable channel when you are installing the device cable. And then you can draw out the cable from the cable channel of the pedestal. Step 3 adjust the device installation pedestal to the proper position and then draw the cable through the cable exit you just dug...
Page 19
14 step 1 please refer to the step 1 in chapter 2.1 to open the device. Step 2 find the “sd card” indicator in the enclosure. Adjust the sd card to the proper direction and then install. See figure 3-4. Step 3 please refer to the step 5 in chapter 2.1 to complete the installation. Figure 3-4.
Page 20
15 4quick configuration tool 4.1overview quick configuration tool can search current ip address, modify ip address. At the same time, you can use it to upgrade the device. Please note the tool only applies to the ip addresses in the same segment. 4.2operation double click the “configtools.Exe’” icon...
Page 21
16 select the “open device web” item; you can go to the corresponding web login interface. See figure 4-3. Figure 4-3 if you want to modify the device ip address without logging in the device web interface, you can go to the configuration tool main interface to set. In the configuration tool search ...
Page 22
17 figure 4-5.
Page 23
18 5web operation this series ipc product support the web access and management via pc. Web includes several modules includes monitor channel preview, ptz control, system configuration, alarm and etc. Ip camera factory default setup: z ip address: 192.168.1.108. Z user name: admin z password: admin ...
Page 24
19 figure 5-2 if it is your first time to login in, system pops up warning information to ask you whether install control webrec.Cab or not after you logged in for one minute. Please click ok button, system can automatically install the control. When system is upgrading, it can overwrite the previou...
Page 25
20 figure 5-4 please refer to the web operation manual included in the resource cd for detailed operation instruction..
Page 26
21 6faq bug i can not boot up the device. Please click reset button for at least five seconds to restore factory default setup. Sd card write times do not set the sd card as the storage media to storage the schedule record file. It may damage the sd card duration. I can not use the disk as the stora...
Page 27
22 appendix toxic or hazardous materials or elements toxic or hazardous materials or elements component name pb hg cd cr vi pbb pbde circuit board component ○ ○ ○ ○ ○ ○ device construction material ○ ○ ○ ○ ○ ○ wire and cable ○ ○ ○ ○ ○ ○ packing components ○ ○ ○ ○ ○ ○ accessories ○ ○ ○ ○ ○ ○ o: indic...