- DL manuals
- Jayco
- Motorhomes
- 2016 Melbourne
- Owner's Manual
Jayco 2016 Melbourne Owner's Manual
Summary of 2016 Melbourne
Page 1
2016 camping trailers printed on recycled paper 2016 melbourne class c motorhomes 0189568.2016.
Page 3: Recycled
2016 jayco melbourne the jayco ecoadvantage is our company’s commitment to protecting the environment. Through jayco’s company-wide sustainability program, we’re creating better ways to build better rv’s using fewer natural resources. Already, our initiative has created significant impact. As of 201...
Page 5: Able
T able of c ontents w arranty & s ervice about this manual 3 chassis guide 3 warranty packet 3 safety alerts 3 reporting safety defects 4 manufacturing process 5 options & equipment 5 customer responsibility 6 change of address/ownership 6 dealer responsibility 6 suggestions for obtaining service 6 ...
Page 6: Able
T able of c ontents power entry door step 37 entrance door step(s) 37 rv step 37 entrance door 38 keys 38 driver & front passenger seat 38 seat belts 39 child safety restraint systems 39 outside rearview mirrors 40 rear vision camera 40 backing up 41 campsite hook-up 41 electric rear stabilizer cont...
Page 7: Able
T able of c ontents converter 68 12-volt dc system 69 wizard button & reverse protection fuses 69 12-volt fuse panel 70 replacing a fuse 70 12-volt dc outlet 70 batteries 70 to recharge the house batteries 71 dry camping 71 battery storage instructions 71 replacement and maintenance 72 chassis batte...
Page 8: Able
T able of c ontents cooking / comfort heating label 90 refueling warning label 90 p lumbing s ystem plumbing system maintenance 91 monitor panel (if so equipped) 91 (monitor panel appearance and components listed may vary) 91 monitor panel 91 command center panel 91 fresh water system 92 fresh water...
Page 9: Able
T able of c ontents tank heaters (if so equipped) 117 toilet 118 h eating & c ooling air conditioner 121 power roof vent (if so equipped) 121 attic fan control 121 furnace 122 a ppliances microwave 123 cooktops (if so equipped) 123 electric drop in cooktops (if so equipped) 124 gas drop in cooktops ...
Page 10
Abs plastics 139 e xterior cleaning the exterior 141 frame 143 chassis maintenance 143 front axle tire alignment 143 exterior roof & sidewall vents 144 windows 144 exterior ladder (if so equipped) 144 sealants 145 t ravel /c amping /s torage c hecklists rv start-up 147 ready to leave checklist 147 m...
Page 11: Warning:
1 warning: read all instructions in this manual and component manufacturer supplied information before using your rv. This manual has been provided by jayco for the sole purpose of providing instructions concerning the operation and maintenance of this vehicle and its components. Nothing in this man...
Page 12
2.
Page 13: & S
3 w arranty & s ervice congratulations! Thank you for selecting a jayco recreation vehicle. We are excited to welcome you to our growing rv family. Jayco is the largest privately held manufacturer of recreation vehicles in the world. We are committed to being the most respected name in rvs. We invit...
Page 14: & S
4 w arranty & s ervice indicates a potentially hazardous situation that, if not avoided, may result in minor or moderate injury. It may also be used to alert against unsafe practices. Indicates an imminently hazardous situation that, if not avoided, will result in death or serious injury. This alert...
Page 15: & S
5 w arranty & s ervice to contact nhtsa by phone: call the department of transportation (dot) vehicle safety hotline at 1-888- 327-4236 and a nhtsa representative will record your complaint information (tty: 1-800-424-9153 or 1-202-484-5238). To contact nhtsa by mail: office of defects investigation...
Page 16: & S
6 w arranty & s ervice c ustomer r esponsibility it is important you read and understand all instructions and precautions before operating the recreation vehicle. Even if you are an experienced rv’er we encourage you to thoroughly read this owner’s manual, as well as the information contained in you...
Page 17: & S
7 w arranty & s ervice note: please provide the following information when contacting us for assistance: ◘ customer name and current location. ◘ phone number where you can be reached. ◘ 17-digit chassis vehicle identification number (vin) or 9-digit serial ◘ the current vehicle mileage (motor homes)...
Page 18: & S
8 w arranty & s ervice mailing address shipping address jayco, inc. Jayco, inc. Customer service customer service p.O. Box 460 100 bontrager drive 903 s. Main street bldg 42 door 4220 middlebury in 46540 middlebury in 46540 phone (toll-free) (800) 283-8267 phone (local) (574) 825-0608 fax (toll-free...
Page 19: & S
9 w arranty & s ervice o btaining e mergency w arranty r epair a roadside emergency can happen at any time, whether your recreation vehicle is new or old. If you are traveling, using the following guidelines can help get you back on the road faster. 1. Call 1-800-rv-jayco or use our website dealer l...
Page 20: & S
10 w arranty & s ervice o btaining s ervice f or s eparately w arranted i tems your selling dealer is responsible for servicing your recreation vehicle before delivery, and has an interest in your continued satisfaction. We recommend your dealer perform all inspection, warranty and maintenance servi...
Page 21: & S
11 w arranty & s ervice p arts & a ccessories contact your independent jayco dealer for assistance in obtaining replacement parts or accessories. Jayco does not sell parts retail direct or to non-authorized dealers. If the original part is no longer available, jayco makes every effort to provide an ...
Page 22: & S
12 w arranty & s ervice jayco shall not be liable for any incidental or conse- quential damages that may result from breach of this limited warranty or any implied warranty. This exclusion of consequen- tial and incidental damages shall be independent of any failure of the essential purpose of any w...
Page 23: & S
13 w arranty & s ervice owner or user files a tax form claiming any business or commercial tax benefit related to the rv, or if the rv is purchased, registered or titled in a business name); any rv sold or used outside the united states, u.S. Territories or canada; any rv not used solely for recreat...
Page 24: & S
14 w arranty & s ervice owner’s manual), unauthorized alteration, off road use, collision or accident, whether or not foreseeable, including any acts of weather or damage or corrosion due to the environment, theft, vandalism, fire, explosions, overloading in excess of weight ratings, and tampering w...
Page 25: & S
15 w arranty & s ervice if, on the other hand, the jayco dealer sells this rv to a retail customer then the rental warranty would not be applicable. The rental warranty does not apply to retail consumers. Jayco’s rental program is applicable to the following product lines: redhawk greyhawk melbourne...
Page 26: & S
16 w arranty & s ervice jayco shall not be liable for any incidental or consequential damages that may result from breach of this limited warranty or any implied warranty. This exclusion of consequential and incidental damages shall be independent of any failure of the essential purpose of any warra...
Page 27: & S
17 w arranty & s ervice but that you are unhappy with; problems related to misuse, mishandling, neglect or abuse, including failure to maintain the rv in accordance with the owner’s manual, or other routine maintenance such as inspections, lubricating, adjustments, tightening of screws, tightening o...
Page 28: & S
18 w arranty & s ervice warranty registrations your warranty registration records should be completed and delivered to the manufacturers of component parts, including the delayed warranty start form for the chassis, which is included in the chassis paperwork. The jayco product warranty registration ...
Page 29
19 o ccupant s afety exit window label s econdary m eans of e scape (e xit w indow ) your recreation vehicle has been equipped with a window(s) that serves as a secondary means of escape. The window(s) will allow a quick exit from the vehicle during an emergency if access to the main entrance door i...
Page 30
20 o ccupant s afety slider window latch style pull the lever down to unlock the window. Slide the window to the right to open and exit the vehicle. The screen does not need to be removed from the window. Lever style latch remove the screen by pulling the red tab (upper right arrow). Pull the lever ...
Page 31
21 o ccupant s afety do not turn the electrical power back on or plug in any appliances after the use of a fire extinguisher. Please refer to the fire extinguisher’s user manual for further instructions on maintenance and clean up. Do not check the pressure, test or practice using the fire extinguis...
Page 32
22 o ccupant s afety they are not fool proof. Smoke alarms only work if they are operational and maintained. Be sure to read, understand and follow the user information provided from the manufacturer of the smoke alarm, including information regarding the limited life of smoke alarms. Please be awar...
Page 33: / P
23 o ccupant s afety maintenance gently vacuum off any dust on the cover of the smoke alarm with your vacuum’s soft brush attachment. Test the smoke alarm once you have vacuumed. Never use water, cleaners or solvents to clean the smoke alarm as they may damage the smoke alarm. Do not paint the smoke...
Page 34
24 o ccupant s afety the alarm is wired directly to the 12-volt electrical system, with continuous power being supplied by the recreation vehicle battery. There is no 9-volt battery power supply in the carbon monoxide/propane alarm. If the battery cable is disconnected at the battery terminals, the ...
Page 35
25 o ccupant s afety it is not designed to detect smoke, fire or any other gas. Please note that there are hazards against which carbon monoxide detection may not be effective, such as natural gas leaks or explosions. This alarm is designed to sense the presence of carbon monoxide/propane gas, howev...
Page 36
26 o ccupant s afety alarm signals normal operation: the led will maintain a steady green light, indicating that the alarm is powered. Co alarm condition: the red led light will remain steady and the alarm will sound 4 “beeps” then silent for 5 seconds. These signals indicate immediate action is req...
Page 37
27 o ccupant s afety lp/carbon monoxide detector formaldehyde label (alarm may vary from model shown) refer to the warranty packet for more information from the carbon monoxide/ propane alarm manufacturer. F ormaldehyde some components in the recreation vehicle contain formaldehyde-based adhesives t...
Page 38
28 o ccupant s afety c ondensation condensation is a natural phenomenon. The amount of condensation will vary with climate conditions, particularly the relative humidity. Condensation occurs because there is water vapor present in the air, which each of us adds to by breathing, bathing or cooking. T...
Page 39
29 p re - travel information w eight t erms gross vehicle weight rating (gvwr) – the value specified by the manufacturer as the maximum permissible weight of the fully loaded motor home. Gross axle weight rating (gawr) – the value specified by the vehicle manufacturer as the load-carrying capacity o...
Page 40
30 p re - travel information federal occc and voluntary weight labels federal occc and voluntary weight labels towing & braking warning label the upper portion of the label is the federally required occc label that indicates the total combined weight value of occupants and cargo that may be placed i...
Page 41
31 p re - travel information do not exceed any applicable motor home weight ratings. Doing so could damage your motor home or affect handling and braking characteristics. Motor home weight information label federal label the factory-installed weight labels are specific to the recreation vehicle for ...
Page 42
32 p re - travel information for traveling safety, it is important to make sure the tie down straps are secured on all appliances such as the toaster, coffee maker, etc. Vibration during travel will move the appliances, creating the potential for them to fall out of their cabinets possibly causing i...
Page 43
33 p re - travel information w eighing y our m otor home now that your motor home is loaded you should have it weighed. The actual weight of the motor home, passengers, all options, liquids, the hitch weight of your towed vehicle and your personal cargo is important for you to know so you do not exc...
Page 44
34 p re - travel information dump the gray and black water holding tanks before traveling to avoid carrying unnecessary weight. Traveling with the tanks full can affect your fuel consumption, and depending on the location of the tanks, can affect your vehicle handling characteristics. If you are dry...
Page 45
35 v ehicle o peration towing and braking label v ehicle o peration you will find that your motor home will travel safely and comfortably at highway speed limits. However, it will take longer than a passenger automobile to reach that speed. Keep this in mind when overtaking and passing another vehic...
Page 46: & S
36 v ehicle o peration in addition, a separate supplemental braking system must be installed if the towed trailer or vehicle meets or exceeds the minimum weight determined by the chassis manufacturer (this minimum weight rating will vary by chassis and chassis manufacturer). Contact you dealer for a...
Page 47
37 v ehicle o peration third brake light that activates when the brakes are engaged. When descending a long hill, drop down into a lower gear (or lower range if you have automatic transmission). Avoid conditions that require excessive and prolonged use of your brakes. Apply and release brakes at sho...
Page 48: & F
38 v ehicle o peration note: locks on entrance and baggage doors need biannual lubri- cation using a light coat of silicone spray. Conditions such as rain, salt, dust and pollution may increase the maintenance needs. Make sure the entrance door is completely closed and locked when traveling. Locking...
Page 49
39 v ehicle o peration s eat b elts seat belts are installed in your motor home to protect the driver and passengers. Always use seat belts. In an accident, injury to the driver and passengers may be reduced if seat belts are properly used. The booth dinette, hide-a-bed sofa, and easy bed sofa have ...
Page 50
40 v ehicle o peration adjust the outside rearview mirrors before driving. The rear vision camera aids in the use of, but does not replace vehicle side/ rear-view mirrors o utside r earview m irrors after adjusting the front driver’s seat, adjust the outside rearview mirrors to your driving preferen...
Page 51
41 v ehicle o peration c ampsite h ook -u p refer to electrical system section before connecting the shore line power cord (when using full hook-up) or before starting the generator (if so equipped) or operating the vehicle on 12-volt power when dry camping. Refer to fuel & lp system section before ...
Page 52
42 v ehicle o peration e lectric r ear s tabilizer c ontrol ( if so equipped ) your motor home may be equipped with an electrically operated rear stabilizer control. The (2) stabilizers are located at the rear of the coach, and when extended, will keep the motor home from rocking side to side. The c...
Page 53
43 v ehicle o peration e mergency s topping always carry road flares or reflective warning signs to display if necessary. Pull off the roadway as far as possible for emergency stopping or tire changing. Turn on your vehicle hazard warning flashers. If traveling at night, use three red warning indica...
Page 54
44 v ehicle o peration f ront a xle t ire a lignment the term alignment refers to both the adjustment angles on the steering axle and suspension and tracking of the rear axle. Many factors are considered when establishing proper alignment. Steering components, suspension, wheel bearings and even pro...
Page 55: & B
45 v ehicle o peration note: the proper method of tightening wheel lug nuts is with a torque wrench, not with an impact wrench or by hand. Because of the importance of having proper torque on the wheel lug nuts, you should always have the wheels mounted and properly torqued by a qualified technician...
Page 56
46 v ehicle o peration it is recommended that the tire pressure be checked at the beginning of each trip to obtain the maximum life of the tire. Follow the instructions listed on the federal certification label to determine the correct tire pressure. . Failure to follow proper inflation guidelines m...
Page 57: A T
47 v ehicle o peration the motor home is very heavy. Raising the motor home to replace the spare tire should only be done with extreme caution by a qualified technician. The vehicle could slip, causing personal injury or death. Do not attempt to do this yourself.. C hanging a t ire if you experience...
Page 58
48 v ehicle o peration do not use the hydraulic leveling jack system to support the motor home while under the vehicle or changing tires. The hydraulic leveling system is designed as a leveling system only. Do not use the hydraulic leveling jack system as a jack or in conjunction with a jack. It is ...
Page 59
49 v ehicle o peration do not set the individual arm pitch at more than three (3) positions different between the left and right arms. Damage to the arms and the canopy can occur if the awning is retracted when the arms are set at more than three (3) positions difference. O perating p ower a wnings ...
Page 60
50 v ehicle o peration 1. Hold on to the awning arm to keep it steady while adjusting the pitch. 2. Press in the pitch adjustment pins located on the scissor arm. 3. Slide the scissor arm to the desired set hole – towards the coach for a lower pitch and away from the coach for a higher pitch. Emerge...
Page 61
51 v ehicle o peration 1. Remove the front cover. The cover snaps onto the rear cover. To remove, press on both sides of the rear cover until the front cover releases then lift the cover off. 2. Detach the red and black wires from the cable to the motor. 3. Attach jumper wires to the motor wires. 4....
Page 62
52 v ehicle o peration.
Page 63
53 s lideout s ystems make sure the interior slideout room path and the slideout room itself is clear of people and objects before operating. Keep away from the slide rails and gear assembly when the room is in motion. They may pinch or catch on loose clothing causing personal injury. Failure to fol...
Page 64
54 s lideout s ystems do not work on your system unless the 12-volt dc (auxiliary battery, customer supplied) and 120-volt ac electrical systems (shore line power cord) have been disconnected. Note: do not operate the switch after the room is fully extended as damage can occur to the motor and/or sw...
Page 65
55 s lideout s ystems trouble shooting the inwall slideout system checking fuses: the inwall slide requires a minimum 30 amp fuse. Check the load center for blown fuses and replace any if necessary. If the fuse blows immediately upon replacement, there is a problem with the wiring to the inwall slid...
Page 66
56 s lideout s ystems 1. Locate the slideout system controllers. There should be one for each slideout on the recreation vehicle. They are typically located in the basement compartment in the forward section of the recreation vehicle, either on the forward wall or on the ceiling. In some models they...
Page 67
57 s lideout s ystems manually pushing in the slideout 1. Locate the slideout system controller 2. Unplug motor 1 and motor 2 connectors at the bottom of the slideout controller. This releases the motor brakes for each motor. 3. The slideout room can now be manually pushed in. Larger rooms may requi...
Page 68
58 s lideout s ystems refer to the schwintek slide room operation guide for further information. Call lippert at (866) 524 – 7821 or visit the lippert website at www.Lci1.Com for additional troubleshooting information. Flush floor slideout for optimum performance, the slide-out system requires full ...
Page 69
59 s lideout s ystems it is important to note that you do not need to attempt to disengage the motor as the actuator is “manual ready” just hook up and crank. Use extreme caution when extending and/or retracting room using the manual override feature. It is possible to operate the slideout beyond th...
Page 70
60 s lideout s ystems electric operation extending the room 1. Level the unit. 2. Main power switch at stepwell (locations may vary) must be on. 3. Verify the battery is fully charged and hooked up to the electrical system. 4. Remove the transit bars (if so equipped). 5. Press and hold the in/out sw...
Page 71
61 s lideout s ystems when these items have been checked and the room still does not move when the switch is pressed, follow the steps below to manually override the slideout room. 1. Turn the main power off. The override will not work if it has power going to it. Do not work on the system unless th...
Page 72
62 s lideout s ystems the rear of the motor) about 1/8 of a turn to the released position (fig. 2). This will release the brake that holds the room in place. 5. Locate the manual override for the slideout system (fig. 1). 6. The room is now free to move. Using either a 5/8” or 3/4” wrench or socket,...
Page 73
63 e lectrical s ystem i n c ase o f a n e lectrical f ire 1. Have everyone evacuate the motor home immediately. 2. Switch the 120-volt main circuit breaker in the motor home to the “off” position 3. Disconnect the negative battery cable(s) at the battery. 4. Disconnect the power cord from the shore...
Page 74: Gfci R
64 e lectrical s ystem c ontrols and s witches your motor home is equipped with a command center that allows you to monitor several systems from one location. For your convenience, the command center is located near the kitchen area. More information on the controls located in the command center wil...
Page 75: 30-
65 e lectrical s ystem t esting the c ampsite p ower c onnection the campsite 120-volt power receptacle(s) should always be tested for proper functionality prior to plugging the recreation vehicle shore power cord into it. Do not plug the shore power cord into a campsite receptacle(s) that has rever...
Page 76: 30 Amp E
66 e lectrical s ystem the power cord must be fully extended when in use and not left coiled in the electrical compartment or on the ground. If the power cord is left coiled, it may potentially create enough heat to melt its protective casing.. C alculating 30 amp e lectrical l oad (i f s o e quippe...
Page 77: 120-
67 e lectrical s ystem 120-volts equals 10 amps. Only connect the shore power cord to properly wired 30 amp nema tt30 120 volt power receptacles. Do not hook up the power cord to any receptacle until you have verified proper polarity and grounding. Polarity indicators can be purchased in most electr...
Page 78
68 e lectrical s ystem replacement only replace circuit breakers with those of the same specified type, voltage, and current rating. Never replace a circuit breaker with one listed at a higher amperage rating. Please contact your dealer for repair assistance when replacing circuit breakers. Maintena...
Page 79: 12-
69 e lectrical s ystem overheating occur. Overheating can be caused by operating the converter above its maximum power output for an extended period of time, or by an obstruction to its ventilation air flow. To reduce converter heat build, keep unnecessary 12-volt lights and motors turned “off”. Kee...
Page 80: 12-
70 e lectrical s ystem 12- volt f use p anel the 12-volt fuse panel is labeled to indicate fuse sizes, positions and the components powered. At the beginning of camping season, inspect all the 12-volt fuses and replace as needed. Fuses are located in the load center. Replacing a fuse before replacin...
Page 81
71 e lectrical s ystem to recharge the house batteries when the engine is running, the alternator will automatically charge the house batteries through the auxiliary start solenoid. When parked at a campsite and plugged into shore power the power converter will automatically charge the batteries. Co...
Page 82: 12-V
72 e lectrical s ystem replacement and maintenance for accuracy, test battery voltage using a volt-ohm meter (customer supplied). When it is time to replace the house batteries, replace with group 27 deep cycle batteries only. Contact the battery manufacturer for further information. Do not reverse ...
Page 83
73 e lectrical s ystem longer than 1 second. Depressing and holding the switch down will disable the battery disconnect solenoid. Should this occur the main ground cable for the house batteries must be removed for 1 minute to re-enable the solenoid operation. Always leave the ignition key in the “of...
Page 84
74 e lectrical s ystem a pproximate e lectrical l oad r atings 12 volt system aisle lights 1.0 amp baggage compartment lights 1.4 amps decorative wall lights 1.5 amps dinette light 4.5 amps exterior entertainment center 5-7 amps fantastic fan 1.5 amps fluorescent double lights -12” 2.0 amps fluoresc...
Page 85
75 e lectrical s ystem g enerator your motor home is equipped with a diesel powered generator and a generator slide tray. The generator produces 120/240-volt power compatible with the motor home electrical system. It can be used to power the entire motor home when 120/240-volt shore power is not ava...
Page 86
76 e lectrical s ystem to manually start the generator 1. A generator “start/stop” switch is installed in the dash panel. A second generator “start/stop” switch is located on the generator itself. 2. At either “start/stop” switch, press and hold the upper portion of the switch to start the generator...
Page 87
77 e lectrical s ystem generator. Consult the oem manual for operator programming information. 2. The ags system is enabled by pressing the auto gen key followed by pressing the enter key on the face of the energy command control panel. You will be asked to momentarily turn the chassis ignition swit...
Page 88
78 e lectrical s ystem r eplacing l ight b ulbs before replacing a bulb, be sure the light is off. Do not touch the glass part of the new bulb with your bare fingers. The skin oil left on the glass will evaporate when the bulb gets hot, the vapor will condense on the reflector and it will dim the su...
Page 89
79 e lectrical s ystem led lights, front cap led accent lights cargo bed red lighted master control switch slideout control switches (press and hold to extend / retract) awning control switches (press and hold to extend / retract) command center panel with switch modules: items may include separate ...
Page 90
80 e lectrical s ystem.
Page 91: & P
81 f uel & p ropane s ystem d iesel f uel & f ill for your protection and others, it is critical to understand the danger associated with fuel. Take time to become educated about the property of fuel and use it safely . Fuel selection use diesel fuel only. Remember the diesel generator (if so equipp...
Page 92: & P
82 f uel & p ropane s ystem fuel spills represent a serious fire hazard, and should be cleaned up immediately. Never restart an engine or re-light any pilot lights while raw fuel is present. If you spill fuel on the motor home, clean it up immediately. Fuel can dull or soften paint and damage other ...
Page 93: & P
83 f uel & p ropane s ystem fuel filler cap remove the fuel filler cap by slowly turning it counterclockwise and waiting for any “hiss” noise to stop. Then unscrew the cap all the way. To close the fuel filler cap, securely turn the cap clockwise until you hear clicking sounds. Filling the fuel tank...
Page 94: & P
84 f uel & p ropane s ystem if you suspect that exhaust fumes are entering the passenger compartment, have the cause determined and corrected as soon as possible. If you must drive under these circumstances, close all the windows, and adjust the heating or cooling system to force outside air into th...
Page 95: & P
85 f uel & p ropane s ystem maintenance although your motor home has been carefully tested at the factory and by your selling dealer for leakage, travel vibrations can loosen fittings. Have the vehicle propane system checked at all connections soon after the purchase of your vehicle, and after the i...
Page 96: & P
86 f uel & p ropane s ystem p ropane s afety p rocedure propane is a colorless and odorless gas that, in the liquefied state, resembles water. An odorant (usually a sulfur compound) is added as a warning agent. If you smell propane within the vehicle, quickly and carefully perform the procedure list...
Page 97: & P
87 f uel & p ropane s ystem servicing or filling because the container is not removable, the motor home will need to be driven to a qualified propane facility for servicing or filling. Only the authorized gas service technician(s) should be near the motor home while the propane tank is being filled....
Page 98: & P
88 f uel & p ropane s ystem if you suspect your propane container has been overfilled, contact your dealer or a qualified propane technician for assistance immediately. Do not attempt to service a propane container overfill yourself. “do not fill to more than 80%” label u sing t he p ropane s ystem ...
Page 99: & P
89 f uel & p ropane s ystem c ooking w ith p ropane g as unlike homes, the amount of oxygen supply is limited due to the size of the recreation vehicle. Proper ventilation when using the cooking appliance(s) will help you avoid the danger of asphyxiation. It is especially important that cooking appl...
Page 100: & P
90 f uel & p ropane s ystem t raveling with p ropane use care when fueling your motor home. Make certain your propane tank is properly fastened in place. The label listed below should be kept permanently affixed to your rv: ensure a supply of fresh air (canada units only) cooking / comfort heating l...
Page 101
91 p lumbing s ystem there are two different water systems in your recreation vehicle: the fresh water system consists of the fresh water holding tank, fresh water connections, water pump, outside shower assembly (if so equipped), water heater, faucets, tub/ shower, and water purification system (if...
Page 102
92 p lumbing s ystem do not drink water deemed microbiologically unsafe or of unknown quality.. F resh w ater s ystem all water contains contaminant and mineral particles that can cause fresh water system odors. Untreated well water is a major source of water system odors. The fresh water (or potabl...
Page 103: 12-V
93 p lumbing s ystem f resh w ater h olding t ank there may be several ways to fill the fresh water tank depending on the model. For details of each method, refer to the fresh water connections or the utility center (if so equipped) sections. There are plastic overflow tubes plumbed into the fresh w...
Page 104
94 p lumbing s ystem will stay on. The water pump automatically recycles when pressure drops. Some cycling may occur depending on the volume of water being released. Turn the water pump switch off when it is not in use. Depending on th,the water pump switch should be in the off position when the rv ...
Page 105
95 p lumbing s ystem u tility c enter the following information defines the function of the utility center water valve settings indicated on the utility center label: city fixtures - allows you to access water from all faucets using a pressurized water source (referred to from here on as “city water...
Page 106
96 p lumbing s ystem you should always use a non-toxic drinking water hose dedicated only to supplying the motor home with fresh water through the city water connection inlet. To reduce the chance of contamination, prevent the non-toxic drinking water hose from coming into contact with the ground. I...
Page 107
97 p lumbing s ystem 7. Turn the appropriate (12-volt gas or 120-volt electric) storage water heater power switch on. (for a tankless water heater (if so equipped) turn the water heater power switch on (the switch is located outside the rv at the water heater panel). The water will be heated on dema...
Page 108
98 p lumbing s ystem note:filters should be replaced at the beginning of each camping season or if they have come into contact with contaminated water. Note:when not in use, the water filter cartridge should be stored out of freezing temperatures. Rv antifreeze will damage the water filter cartridge...
Page 109
99 p lumbing s ystem to replace filter cartridge 1. Turn off water supply using two valves located on the water lines on each side of the canister. 2. Place drip pan below filter housing to catch any spillage. 3. Press the red button on top of the filter housing to release pressure. 4. Using a spann...
Page 110
100 p lumbing s ystem w ater h eater operating instructions your motor home may be equipped with either a tank (storage) water heater or tankless water heater. The following is an overview of both systems. For detailed operating instructions, refer to the manufacturer’s owner’s manual supplied in yo...
Page 111
101 p lumbing s ystem the dsi water heater is designed to heat water quickly and efficiently. The water heater manufacturer has preset the sensing limit to maintain the water temperature when the water heater is activated. The thermostat on your water heater is not adjustable. It is a temperature se...
Page 112
102 p lumbing s ystem anode rod replacement chart note: it is important that once the motor home has returned to lower elevation (below 4500 feet) any high altitude deration or other adjustments be reversed for proper operation of the water heater. Do not place a valve between the pressure and tempe...
Page 113
103 p lumbing s ystem the temperature and pressure relief valve is designed to open if the temperature of the water within the heater reaches 120° f, or if the water pressure in the heater reaches 150 pounds. When this pressure is reached, the pressure relief valve will open and water will drip from...
Page 114
104 p lumbing s ystem tankless water heater (if so equipped) your motor home may be equipped with a tankless water heater. The tankless water heater uses less lp gas than storage tank model water heaters since it only uses energy when hot water is demanded. There is no pilot light to burn when no ho...
Page 115
105 p lumbing s ystem scalding injury-explosion valve is not serviceable; if defective it must be replaced. Tampering with valve will result in scalding injury. Do not place a plug or reducing coupling on outlet part of valve. If you use a discharge line allow complete drainage for both valve and li...
Page 116: 3 V
106 p lumbing s ystem 3 v alve w ater h eater b ypass (i f s o e quipped ) most floor plans have a factory installed water heater bypass which enables you to avoid filling the water heater with rv antifreeze. Bypass valves are typically located in close proximity to the water heater. Outside utility...
Page 117: / S
107 p lumbing s ystem note: the shower head may be removed from the hose so that it will drain faster. If you remove the shower head, be sure to reas- semble it prior to storage. Note: when putting the shower assembly back into the storage compartment, make sure the hose is not pinched or the shower...
Page 118: & S
108 p lumbing s ystem exterior freshwater drain the showerhead does not have a complete shut-off valve (the complete shut-off is at the faucet). The showerhead may drip slightly in the off position after use; this is normal and does not indicate a leak or defect. There may be air in the plumbing lin...
Page 119
109 p lumbing s ystem knob turns 45° to open or close). 4. Open the “low point drains” by turning, then pulling the handles up. As their name indicates, they will be at the lowest point of water lines. A label is placed on the outside of the rv to indicate where the drains are located. The drains wi...
Page 120
110 p lumbing s ystem 7. Attach the short hose supplied with your recreation vehicle to the fresh water connection inlet (on the utility center or on the outside of the motor home). Place the other end of the hose in a container holding the sanitized solution. To assist the syphoning process set the...
Page 121
111 p lumbing s ystem 22. Set the (storage) tank water heater bypass valves to normal: hot & cold supply lines on, middle (mixer) valve off. 23. Set utility center water valves to the normal position and turn the pump on to circulate fresh water through the lines. 24. Open hot & cold lines to all fa...
Page 122
112 p lumbing s ystem winterizing with antifreeze method it may be easier to winterize the motor home with another person to assist you. 1. Level the motor home and drain the fresh water plumbing system. 2. Turn the water valves off on each side of the water filter canister. The canister is located ...
Page 123
113 p lumbing s ystem winterizing washing machine (if so equipped) while you are putting antifreeze in the water lines follow these instructions to winterize the washing machine: 1. Set the cycle selector to rinse. 2. Set the wash temperature to warm. 3. Press the on/off button to turn the washer on...
Page 124: & G
114 p lumbing s ystem vehicle speed until you reach a dumping station. When connected to the sewer drain line at a campground, keep the “black tank drain” valve closed until the holding tank is at least ¾ full. This will provide sufficient water to assist in complete draining of the black water hold...
Page 125
115 p lumbing s ystem before operating the macerator pump, make sure the external dump hose is properly attached at the motor home and at the dump station. The hose is under pressure and therefore waste is discharged under pressure. Failure to follow instructions can lead to possible injury or prope...
Page 126
116 p lumbing s ystem 4. Turn the macerator power switch on at the utility center panel and the macerator pump will begin sending waste through the dump hose. 5. When the tank is empty, turn the macerator power switch off. Close the black tank drain valve. 6. Select the gray drain valve. 7. Turn the...
Page 127
117 p lumbing s ystem 4. Disconnect the garden hose and close the “black tank drain” valve. Fasten the sewer hose housing dust cap back on the “black tank flush.” the black tank drain valve must be open any time there is a hose (water supply) connected to the black tank flush. Do not leave any hose ...
Page 128
118 p lumbing s ystem t oilet the toilet is efficient and easy to operate. Generally, more water is required only when flushing solids. Prior to using the sanitation system, it is strongly recommended to flush the toilet several times to release sufficient water into the holding tank. If there is no...
Page 129
119 p lumbing s ystem do not use chlorine (undiluted) or caustic chemicals, such as laundry bleach or drain opening types, in the toilet system. These products damage the seals in toilets and dump valves. For detailed information refer to the manufacturer’s operator manual. Table of contents mainten...
Page 130
120 p lumbing s ystem notes:.
Page 131: & C
121 h eating & c ooling a ir c onditioner your motor home has a roof mounted air conditioning system that is controlled by a thermostat. Cooled air enters the motor home through the adjustable “chill grill.” make sure you have sufficient power available before operating the air conditioner. Do not o...
Page 132: & C
122 h eating & c ooling the furnace should be inspected periodically (monthly during the heating season) for presence of soot on the vent. Soot is formed whenever combustion is incomplete. This is a visual warning that the furnace is operating in an unsafe manner. If soot is observed on the vent, im...
Page 133
123 a ppliances never use the microwave cavity for storage. The microwave cavity should always be empty when not in use note: to prevent damage, remove the turntable from the micro- wave when traveling. M icrowave microwave oven use for list of preset programs, see the quick reference guide provided...
Page 134
124 a ppliances cleaning instructions refer to the manufacturer’s user guide included in your warranty packet for detailed cleaning instructions. General cleaning be sure appliance is off and all parts are cool before handling or cleaning. This is to avoid damage and possible burns. Use care to avoi...
Page 135: & O
125 a ppliances gas drop in cooktops (if so equipped) drop in cooktops add compact high efficiency cooking performance to your recreation vehicle. Depending on your model, it may be equipped with either a 2 burner or 3 burner cooktop. The 2 burner match-light cooktop has two 6500 btu/h burners with ...
Page 136
126 a ppliances range hood vent r ange h ood (i f s o e quipped ) if your recreation vehicle is equipped with a range hood, it will be connected to an exterior vent. The vent has an inner flap with two snaps. This flap can be snapped shut when the vehicle is in motion, or during storage to keep inse...
Page 137: A G
127 a ppliances i n c ase o f a g rease f ire grease is flammable. Never allow grease to collect around top burners or on the cook top surface. Wipe up spills immediately. Refer to section 2 – safety precautions, for fire safety and fire extinguisher information. Do not attempt to use water to put o...
Page 138: – S
128 a ppliances c leaning y our r efrigerator the following are general cleaning guidelines. For detailed information on cleaning your specific refrigerator, refer to the manufacturer’s user’s guide. Cleaning the interior 1. Unplug refrigerator or disconnect power. 2. Hand wash, rinse, and dry remov...
Page 139: Hdtv A
129 e lectronics hdtv a ntenna (i f s o e quipped ) your recreation vehicle may be equipped with an exterior amplified high definition tv antenna. The antenna comes equipped with a signal meter and a power injector to aid in receiving the strongest possible signal when tuning in hdtv stations. Anten...
Page 140
130 e lectronics rotate the antenna knob to illuminate the last flickering led. Refer to your tv (or converter box) manual for information on how to scan for available channels. Refer to the hdtv manufacturer’s manual for detailed operating and safety information. T elevision r oof a ntenna ( if so ...
Page 141
131 e lectronics rotate slowly when selecting station and check fine tuning on tv set to make sure it is properly adjusted. Lower antenna before moving vehicle. Dont’s don’t force elevating crank up or down. Don’t rotate directional handle hard against stops. Don’t travel with lift in up position. D...
Page 142
132 e lectronics notes:.
Page 143
133 i nterior d écor i tems décor items such as décor glass, furniture, window treatments, shades and blinds should be cared for as follows: décor glass (if so equipped) use a glass cleaner to remove smudges, smears and spots. If there is any decorative etching on the décor glass, use care when clea...
Page 144
134 i nterior to remove stuck on dust or stains refer to the following guide. Solar shields: use a sponge or soft brush and water to remove stains. A mild cleaning solution can be used to remove tougher stains. Rinse after cleaning by wetting a clean cloth in fresh water, wringing our any excess and...
Page 145
135 i nterior you may want to place a cover or air mattress (customer supplied) over the sofa when it is in the sleeping position. Trifold sofa the trifold sofa offers very similar features to the traditional hide-a-bed. The following illustrations detail converting the sofa into a bed. 1. Remove tr...
Page 146: & T
136 i nterior up on the bottom seat support. If the bottom seat support is secured closed with screws, do not remove the seat support or use this area for storage. The dinette seats that are secured with screws contain factory installed equipment and should only be accessed by a qualified service te...
Page 147
137 i nterior p antry or h utch (i f s o e quipped ) depending on the kitchen layout of your recreation vehicle, you may have a pantry or hutch that you can use to store items you wish to take with you as you travel and camp. Make sure all items stored in the pantry or hutch are secured so they do n...
Page 148
138 i nterior difficult stains can be removed from the matte finish with a green scotch brite® pad and a mild abrasive cleaner. Disinfect the surface periodically with diluted household bleach (one part water to one part bleach). For cuts and scratches, sand the matte finish lightly with (220) fine ...
Page 149: Abs P
139 i nterior to care for the vinyl floor covering, use a damp mop with water and a mild cleaner on the entire floor. Do not soak the flooring. Use care to avoid wetting the carpet edges. To avoid problems of “yellowing” linoleum, the flooring manufacturer recommends avoiding cleaners that contain o...
Page 150
140 i nterior notes:.
Page 151
141 e xterior c leaning t he e xterior to protect your recreation vehicle’s exterior finish, wash it often and thoroughly. For recreation vehicles with painted exterior graphics: if desired you may wash and wax your vehicle 60 days after purchase. The exterior paint does need time to cure before any...
Page 152
142 e xterior do not use waxes containing high-abrasive compounds. Such waxes remove rust and stains effectively from the paint work, but they are also harmful to the luster of the painted surface since they scrape off the coating. Further, they are detrimental to glossy surfaces, such as the grille...
Page 153
143 e xterior polishing your recreation vehicle if painted surfaces have been severely damaged and have lost their original luster and color tone, polish the surface lightly with a fine polishing compound. Avoid limiting your polishing to the damaged surface only; polish a somewhat wider area, movin...
Page 154: & S
144 e xterior w indows any ventilating window may permit water inside, especially during heavy rainstorms or while driving. This is normal and water should only be seen in the lower track portion of the window frame. Condensation will also cause water to accumulate on windows and in the tracks. Ensu...
Page 155
145 e xterior to check the exterior sidewall sealants, use a stepladder placed safely alongside the vehicle. Do not prop a ladder against the body of the motor home as it may damage the exterior finish s ealants sealants perform a very important function and should be inspected closely and regularly...
Page 156
146 e xterior notes:.
Page 157: Rv S
147 t ravel /c amping /s torage c hecklists rv s tart -u p the following checklist will help ensure a trouble-free camping and travel season: inspect and work all interior and exterior latches and locks (lube if necessary). Make sure the batteries are fully charged and installed correctly. Turn on t...
Page 158
148 t ravel /c amping /s torage c hecklists m otor home s torage properly preparing your motor home for storage during periods of non-usage will prevent problems from arising. It will also make it easier to get started again for the following camping trip or season. To prevent costly freeze-ups, win...
Page 159
149 t ravel /c amping /s torage c hecklists inspect and clean tires. Check for wear, cracks and inflation pressure. Inspect under the motor home for any openings into the floor where animals or insects may enter and seal if necessary. Turn the furnace thermostat(s) to the off position. If your motor...
Page 160
150 t ravel /c amping /s torage c hecklists notes:.
Page 161
151 a dditional i nformation f eatured c omponents q uick r eference c hart your recreation vehicle may be equipped with some of the items listed below. This is a partial listing and it is not intended to cover all components. All information is the latest available at the time of publication. Jayco...
Page 162
152 a dditional i nformation v ehicle m aintenance r ecord make: model: model year: vehicle serial#: engine: engine serial#: service date mileage work performed performed by notes.
Page 163
153 a dditional i nformation service date mileage work performed performed by notes table of contents maintenance record.
Page 164
154 a dditional i nformation notes:.
Page 165
155 a dditional i nformation jayco ownership notification fax form to: (800) 825-7876 □ change of owner □ transfer of limited warranty (see limited warranty for details) model information: serial#:______________________ chassis #: _______________________ odometer reading ______________ (motorized on...
Page 166
156 a dditional i nformation notes:.
Page 167
157 a dditional i nformation notes: table of contents maintenance record.
Page 168
158 a dditional i nformation notes:.
Page 169
159 a dditional i nformation notes: table of contents maintenance record.