- DL manuals
- Jayco
- Motorhomes
- Precept 2018
- Owner's Manual
Jayco Precept 2018 Owner's Manual
Summary of Precept 2018
Page 1
2016 camping trailers 2018 class a motorhome owner’s manual printed on recycled paper 0230295.2018.
Page 3: Recycled
The jayco ecoadvantage is our company’s commitment to protecting the environment. Through jayco’s company-wide sustainability program, we’re creating better ways to build better rv’s using fewer natural resources. Already, our initiative has created significant impact. As of 2014 our company has: re...
Page 4
47 section 4: vehicle operation to set a new code, wake up the lock by touching the wake up area. Then touch and hold both the “ 3
Page 5: Table of Contents
Table of contents section 1: warranty & service customer relations 11 to contact us 13 jayco travel club 13 about this manual 14 warranty packet 14 chassis guide 14 safety alerts 14 reporting safety defects 15 customer responsibility 16 change of address/ownership 16 suggestions for obtaining servic...
Page 6: Table of Contents
Table of contents rear vision camera 51 campsite hook-up 52 lippert motorized leveling plus (if so equipped) 52 emergency stopping 55 emergency towing 56 front axle tire alignment 56 wheel lug nuts/wheel liners 57 tires 58 changing a tire 60 awnings (if so equipped) 60 awning care 61 electric patio ...
Page 7: Table of Contents
Table of contents 12-volt battery disconnect 90 battery isolator solenoid (if so equipped) 90 battery isolation manager (if so equipped) 90 auxiliary start system (if so equipped) 90 load center 91 120-volt circuit breakers 91 approximate electrical load ratings 92 120-volt (50 amp) ac system (if so...
Page 8: Table of Contents
Table of contents draining the fresh water system 111 filter housing 111 nautilus p3 uni-dock utility center 112 low point drains 112 exterior fresh water drain 112 sanitizing the plumbing system: 116 winterizing the plumbing system: 119 truma® tankless water heater (if so equipped) 122 outside show...
Page 9: Table of Contents
Table of contents cabinetry & tables 146 interior wall panel 146 abs plastics 147 sofa & dinette 147 hide-a-bed sofa or sofa sleeper 147 jack knife sofa 147 dream dinette unlocked 148 dream dinette locked 148 trifold sofa 148 booth dinette (if so equipped) 148 booth dinette 148 dream dinette 148 fre...
Page 11: Warning:
9 warning: read all instructions in this manual and component manufacturer supplied information before using your rv. This manual has been provided by your recreational vehicle manufacturer for the sole purpose of providing instructions concerning the operation and maintenance of this recreational v...
Page 12
10 table of contents maintenance record.
Page 13
11 section 1: warranty & service congratulations! Thank you for selecting a jayco recreation vehicle. We are excited to welcome you to our growing rv family. We are committed to being the most respected name in rvs. We invite you to drop by our visitors center located in middlebury, indiana. To book...
Page 14
12 section 1: warranty & service customer name and current location. Phone number where you can be reached. 17-digit chassis vehicle identification number (vin) or 9-digit serial the current vehicle mileage (motor homes) your date of purchase. If applicable, the component description, serial number ...
Page 15
13 section 1: warranty & service to expedite processing your warranty claim, include your name, address, phone number, rv 17-digit vin and authorization number. If returning parts, include a copy of your return freight bill. Obtaining weekend or after business hours repair assistance if an authorize...
Page 16: About This Manual
14 section 1: warranty & service about this manual this manual is a guide to operation of the features, equipment and controls in your recreation vehicle. If you find components vary significantly from what is described, please contact your dealer to ensure you have the correct information. Nothing ...
Page 17: Reporting Safety Defects
15 section 1: warranty & service note: gives helpful information. This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death. Indicates a potentially hazardous situation that, if no...
Page 18: Customer Responsibility
16 section 1: warranty & service to contact nhtsa by phone: call the department of transportation (dot) vehicle safety hotline at 1-888- 327-4236, and a nhtsa representative will record your complaint information (tty: 1-800-424-9153 or 1-202-484-5238). To contact nhtsa by mail: office of defects in...
Page 19: Items
17 section 1: warranty & service suggestions for obtaining service to help ensure your dealer provides the level of service you expect, here are some suggestions we would like to make: contact your dealer at once… do not wait until you are ready to use your rv. Your dealer may not be able to service...
Page 20: Parts & Accessories
18 section 1: warranty & service the propane system (if so equipped) and all electrical systems must be shut down and turned off. We are not responsible for discharged batteries or propane tanks. During the appropriate season, please ensure the rv has been winterized. Unless prior approval has been ...
Page 21
19 section 1: warranty & service jayco motorized limited warranty this limited warranty covers: the motorhome when it is used only for its intended purpose of recreational travel and camping; only the first retail purchaser; only those portions of the motorhome not excluded under the section “what i...
Page 22
20 section 1: warranty & service their purpose. Some states do not allow the exclusion or limitation of consequential or incidental damages, so the above exclusions may not apply to you. Coverage time: the duration of this warranty is 2 years after the first retail owner takes delivery of the motorh...
Page 23
21 section 1: warranty & service how to get service: to obtain warranty service the owner must: notify jayco or an authorized jayco dealer, within the applicable warranty coverage period designated above, that you are making a warranty claim; provide the notification mentioned in (1), above, within ...
Page 24
22 section 1: warranty & service damage caused by road hazards; any component, system or part that warranted by another entity, such as the: automotive chassis, (including the power train, steering, handling, braking, wheel balance, muffler, tires, tubes, batteries and gauges); generator; hydraulic ...
Page 25: Notice to Jayco Dealers
23 section 1: warranty & service care and maintenance: it is the owner’s responsibility to perform proper care and maintenance of the motorhome and to assure correct load distribution. For details regarding this, please see your owner’s manuals. Please review all manuals and contact your selling dea...
Page 26
24 section 1: warranty & service appearance items at the factory during assembly - repairs to defects and damage are performed at the factory during the inspection process. If you discover a defect or damage to the motorhome when you take delivery of your motorhome, you must notify your jayco within...
Page 27
25 section 1: warranty & service contact jayco, at 903 south main street, p. O. Box 460, middlebury, indiana 46540, attn: customer service, (574) 825-5861 or (800) 283-8267. What is not covered: equipment and appliances installed after the motorhome is assembled by jayco; motorhomes used for any bus...
Page 28
26 section 1: warranty & service jurisdiction. All actions of any kind relating to the motorhome shall be decided by a judge rather than by a jury. Warranty registrations: your warranty registrations should be completed and delivered to the manufacturers of component parts. Your jayco warranty will ...
Page 29: Section 2: Occupant Safety
27 section 2: occupant safety secondary means of escape (exit window) your recreation vehicle has been equipped with a window(s) that serves as a secondary means of escape. The window(s) will allow a quick exit from the vehicle during an emergency if access to the main entrance door is not available...
Page 30: Section 2: Occupant Safety
28 section 2: occupant safety lever style latch remove the screen by pulling the red tab (upper rightarrow). Pull the lever out from the sash clamps. Swing the lever out so it is positioned straight out from the window. Push the lever (and window) out to open and exit the vehicle. Fire safety if a f...
Page 31: Section 2: Occupant Safety
29 section 2: occupant safety inspection and maintenance read and follow all instructions on the label and user’s manual provided by the fire extinguisher manufacturer. Inspect the extinguisher at least once a week (more frequently if it is exposed to weather or possible tampering). This should also...
Page 32: Section 2: Occupant Safety
30 section 2: occupant safety the smoke alarm is operational once the battery is correctly installed. It will not function if the battery is missing, disconnected, dead, the wrong type or not installed correctly. It requires one standard 9v battery. Refer to the user’s guide, for correct battery and...
Page 33: Section 2: Occupant Safety
31 section 2: occupant safety combination carbon monoxide /propane alarm your recreation vehicle is equipped with a combination carbon monoxide (co) / propane alarm that is listed for use in recreation vehicles. The combination carbon monoxide/ propane alarm will only work if it is operational and m...
Page 34: Section 2: Occupant Safety
32 section 2: occupant safety by either exiting the recreational vehicle or calling for assistance. Young children and household pets may be the first affected. Your combination carbon monoxide/propane alarm is designed to detect the toxic carbon monoxide fumes that result from incomplete combustion...
Page 35: Section 2: Occupant Safety
33 section 2: occupant safety equipment and appliances, and inspect for proper operation of this equipment. Make sure that motor vehicle(s) are not, and have not been, operating in an attached garage or adjacent to the recreation vehicle. If problems are identified during this inspection, have the a...
Page 36: Section 2: Occupant Safety
34 section 2: occupant safety note: the carbon monoxide/propane alarm manufacturer strongly recommends replacement of the detector five years after the date of purchase. Formaldehyde some components in the recreation vehicle contain formaldehyde-based adhesives that may release formaldehyde fumes in...
Page 37: Section 2: Occupant Safety
35 section 2: occupant safety condensation condensation is a natural phenomenon. The amount of condensation will vary with climate conditions, particularly the relative humidity. Condensation occurs because there is water vapor present in the air. When the temperature reaches the “dew point” the wat...
Page 38: Section 2: Occupant Safety
36 section 2: occupant safety notes: table of contents maintenance record.
Page 39: Vehicle Labels
37 section 3: pre-travel information vehicle labels decals and data plates used throughout the motor home aid in its safe and efficient operation; others give service instructions. Read all decals, data and instruction plates before operating your recreation vehicle. Any decal, data or instruction p...
Page 40
38 section 3: pre-travel information occc label (occupant & cargo carrying capacity): the upper portion of this yellow label is federally required and indicates the total combined weight value of occupants and cargo that may be placed in or on your motor home as it was manufactured and weighed befor...
Page 41: Loading Your Motorhome
39 section 3: pre-travel information loading your motorhome store and secure all loose items inside the motor home before traveling. Overlooked items can become dangerous projectiles during a sudden stop. Distribute cargo side-to-side so the weight on each tire does not exceed one half of the gawr f...
Page 42: Weighing Your Motor Home
40 section 3: pre-travel information weighing your motor home when your motor home is loaded you should have it weighed. The actual weight of the motor home, passengers, all options, liquids, the hitch weight of your towed vehicle and your personal cargo is important for you to know so you do not ex...
Page 43
41 section 3: pre-travel information see the weight terms and loading your rv sections for important information on how towing a vehicle affects the motor home weight. It is important to redistribute the load to avoid component failure as well as to improve the handling characteristics of the vehicl...
Page 44
42 section 3: pre-travel information notes: table of contents maintenance record.
Page 45: Vehicle Operation
43 section 4: vehicle operation vehicle operation your motor home will travel safely and comfortably at highway speed limits. However, it will take longer than a passenger automobile to reach that speed. Allow more time to go around the vehicle you are passing. Avoid situations that might require su...
Page 46: Using The Rear Hitch
44 section 4: vehicle operation using the rear hitch towing will affect vehicle handling, durability and fuel economy. Exceeding any of the listed weight ratings will result in unacceptable overall vehicle performance. Your safety and satisfaction require proper use of correct equipment. The factory...
Page 47: Power Entrance Step
45 section 4: vehicle operation in addition, a separate supplemental braking system must be installed if the towed trailer or vehicle meets or exceeds the minimum weight determined by the chassis manufacturer (this minimum weight rating will vary by chassis and chassis manufacturer). Contact your de...
Page 48
46 section 4: vehicle operation note:locks on entrance and baggage doors need biannual lubri- cation using a light coat of silicone spray. Conditions such as rain, salt, dust and pollution may increase the maintenance needs. Keyless entry (if so equipped) the keyless entry system is a battery powere...
Page 50
48 section 4: vehicle operation trouble shooting after installation the touch pad does not work ● batteries are dead/need to be replaced or are not installed properly ● plug not engaged properly dead bolt not engaging into door frame ● obstruction in door frame code not working ● remove batteries fo...
Page 51: Driver & Passenger Seat
49 section 4: vehicle operation driver & passenger seat 6-way power seat (if so equipped) use the controls to slide the 6-way power seat to the desired position. Release the control, and the seat will lock at that position. The 6-way power seat has a three-point adjustable seat belt. Features includ...
Page 52: Seat Belts
50 section 4: vehicle operation child safety restraint systems when transporting infants or small children, an appropriate child safety restraint system should always be used. Follow the manufacturer’s instructions for the correct installation and use of these systems. Seat belts always use seat bel...
Page 53: Outside Rearview Mirrors
51 section 4: vehicle operation outside rearview mirrors after adjusting the front driver’s seat, adjust the outside rearview mirrors to your driving preference. Have someone help you adjust the mirrors in the desired direction for maximum rear visibility before driving. During travel, vibration may...
Page 54: Campsite Hook-Up
52 section 4: vehicle operation camera/monitor system aids in the use of, but does not replace vehicle side/rear-view mirrors. Objects in camera/monitor view are closer than they appear. When backing up, proceed cautiously and be prepared to stop. Campsite hook-up refer to electrical systems section...
Page 55
53 section 4: vehicle operation failure to act in accordance with the following warnings may result in serious personal injury or death! The use of the electronic automatic leveling system to support the coach for any reason other than which it is intended is prohibited and will violate terms of the...
Page 56
54 section 4: vehicle operation left jack button: activates left jacks in manual mode. Right jack button: activates right jacks in manual mode rear jack button: activates rear jacks in manual mode auto leveling operation landing gear jacks can be operated any time the system is “on”. Turn the leveli...
Page 57: Emergency Stopping
55 section 4: vehicle operation retract procedure press on/off button to turn on the system.Push and hold the retract all jacks button only until the power unit turns on and the coach begins to lower. Release the button once the retract process has begun. All jacks will start to retract and return t...
Page 58: Emergency Towing
56 section 4: vehicle operation note: curves and/or hills may affect the safe placement of warn- ing indicators. Do not use the stabilizer jacks to level the rv. It is important to remember that the stabilizer jacks are to be used only for support while occupying and moving around the rv. They are n...
Page 59: Wheel Lug Nuts/wheel Liners
57 section 4: vehicle operation wheel lug nuts/wheel liners torque is the amount of rotating force applied to a lug nut, and can only be achieved by using a properly calibrated torque wrench and socket. Do not use a 4-way socket or any other type of wrench that does not measure the actual pressure a...
Page 60: Tires
58 section 4: vehicle operation wheel lugs if you suspect or notice the wheel stud bolts are cracked or broken, they must be replaced, along with adjacent bolts that have probably also been weakened due to the additional stress placed on them. Aluminum wheels (if so equipped) clean the aluminum whee...
Page 61
59 section 4: vehicle operation tire wear should be checked frequently. Once a wear pattern becomes firmly established in a tire it is difficult to stop, even if the underlying cause is corrected. Failure to follow proper inflation guidelines may result in tire failure, which, under certain circumst...
Page 62: Changing A Tire
60 section 4: vehicle operation changing a tire if you experience a flat tire on your motor home while driving, gradually decrease your vehicle speed (if possible), and move the motor home to a safe place on the side of the road. Contact your road service provider (if applicable) or a qualified serv...
Page 63
61 section 4: vehicle operation awning care keep your awnings clean and in good condition to prevent costly repairs. Periodically check that the fasteners are tight. Tighten if necessary. Keep the awning fabric clean. For detailed cleaning information, refer to the manufacturer’s owner information. ...
Page 64
62 section 4: vehicle operation carefree® longitude awnings (if so equipped) offer the following features: scissor style arms that do not require vertical ground supports. Adjustable arms with ( 6 ) position pitch adjustment. Worm gear driver motor eliminating the need for travel locks. Single switc...
Page 65
63 section 4: vehicle operation always operate the awning according to the instructions. Periodically check that the fasteners are tight (tighten if necessary). Keep the awning fabric and arms clean. Refer to the manufacturer’s user guide for detailed operating and safety information. Emergency oper...
Page 66
64 section 4: vehicle operation locate and separate the quick disconnects located in the motor arm channel. Position the wires from the motor on the outside of the channel. 7. Attach jumper wires to the motor wires. Connect the other ends of the jumper leads to the 10vdc–14vdc source. If the awning ...
Page 67: Section 5: Slideout Systems
65 section 5: slideout systems electric slide room(s) (if so equipped) the mechanical components of the slide out are gear driven. Electric powered slideout room systems have a manual override to allow you to extend or retract the slideout room(s) in case of a power loss. Make sure you have sufficie...
Page 68: Section 5: Slideout Systems
66 section 5: slideout systems operating the switch after the room is fully extended or retracted may damage the switch and motor. After the slideout is extended, visually inspect the slideout and the surrounding area to make sure the slideout has extended properly and has adequate clearance from an...
Page 69: Section 5: Slideout Systems
67 section 5: slideout systems electric operation extending/retracting the room 1. Level the unit. 2. Main power switch at stepwell (locations may vary) must be on. 3. Verify the battery is fully charged and hooked up to the electrical system. 4. Remove the transit bars (if so equipped) if extending...
Page 70: Section 5: Slideout Systems
68 section 5: slideout systems schwintek in-wall slideout system the in-wall slideout system requires no maintenance or adjustments. This system has two vertical columns with a drive motor located at the top of each column. The right and left motors are synchronized by a circuit board.Schwintek slid...
Page 71: Section 5: Slideout Systems
69 section 5: slideout systems the room is extended. Trouble shooting the in-wall slideout system checking fuses: the in-wall slide requires a minimum 30-amp fuse. Check the load center for blown fuses and replace any if necessary. If the fuse blows immediately upon replacement, there is a problem w...
Page 72: Section 5: Slideout Systems
70 section 5: slideout systems approximately 5 seconds. 4. The red and green led’s will flash indicating you are in override mode. Release the mode button. 5. Using either a wall or command center panel switch, press and hold the switch toward the word in or retract until the unit comes in completel...
Page 73: Section 5: Slideout Systems
71 section 5: slideout systems 8. Pull the motor up until it disengages (about 1/2 inch). 9. Repeat this process for both sides of the slide room. 10. Physically push/ pull the room back into the opening; keep both sides relatively even. 11. The room must be travel locked to keep the room in place f...
Page 74: Section 5: Slideout Systems
72 section 5: slideout systems unit (or use a ratchet to actuate the motor) to pull the room in or out. If the motor is functioning, check the room for obstructions. Norco slideout manual operation 1. Locate the included flexible shaft in your owner’s packet. 2. Attach flexible shaft to the 1/4” hex...
Page 75: Section 5: Slideout Systems
73 section 5: slideout systems if the room does not move when the switch is pressed, check the following: make sure the slideout system is turned on. Battery is fully charged and connected. Transit bars have been removed (if so equipped). If the room still does not move when the switch is pressed, f...
Page 76: Section 5: Slideout Systems
74 section 5: slideout systems 6. The room is now free to move. Using either a 5/8” or 3/4” wrench or socket, crank the room either in or out completely. If the slideout system is supplied with a gearbox override (optional), use the crank handle to move the room. 7. When the rooms is fully in or out...
Page 77: Section 5: Slideout Systems
75 section 5: slideout systems 5. Turn on the on/off switch or key. 6. Press and hold the out button (fig 4). To retract, press and hold the in button. There will be a slight delay before the room begins moving. 7. The green led should be solid on when room is in motion. 8. Release the out button wh...
Page 78: Section 5: Slideout Systems
76 section 5: slideout systems fault code fault type fault codes description possible cause possible solution 1 major stops not programmed -stops have not been set -stops were cleared -stops were improperly set steps need to be programmed by an authorized service facility. 2 minor system fault -obst...
Page 79: Section 5: Slideout Systems
77 section 5: slideout systems emergency retract mode: use this procedure when there is no loss of power or electrical problem with the system. 1. Remove the touchpad (fig 4) from the wall. 2. Prior to clearing the major fault, record the number of red & green flashes observed on the touchpad (fig 6...
Page 80: Section 5: Slideout Systems
78 section 5: slideout systems 5. Unplug the motor from the harness and remove the motor by lifting it up and out. 6. Repeat steps 1-4 for the other side. 7. Place a socket wrench with a 3-inch extension and a 5/8” deep well socket (fig 12) through the motor access opening and seat the socket onto t...
Page 81: Section 5: Slideout Systems
79 section 5: slideout systems power gear ram slideout system typically used for class c motorhomes. Manual override procedure: the system has been equipped with 3/4” hex override couplers located on the drive component of the system. Due to the size and weight of some rooms, assistance may be neede...
Page 82: Section 5: Slideout Systems
80 section 5: slideout systems 12. Return the brake release lever back to the “engaged” position (parallel to the spring lock lever). Pressing the bent end of the spring lock lever will allow the brake lever to be moved. 13. Plug the motor connector back in again. 14. Replace the plastic motor cover...
Page 83: Section 6: Electrical System
81 section 6: electrical system the electrical system the rv electrical system is comprised of two independent electrical systems. One operates off of 12-volt dc power and the other off of 120-volt 60hz ac power. All installations have been made in compliance with industry standards applicable on th...
Page 84: Section 6: Electrical System
82 section 6: electrical system controls and switches your motor home is equipped with various switches and controls that allow you to operate and monitor the systems in your motor home. Information on these controls and their location will be provided throughout this manual. Additional information ...
Page 85: Section 6: Electrical System
83 section 6: electrical system note: if your rv model includes the 5 way/8 way remote control: the light button on the remote only controls the awning led lights the dimmer has a memory so it remembers what the light setting was when the lights were turned off. When turned on again, the lights retu...
Page 86: Section 6: Electrical System
84 section 6: electrical system do not hook up the power cord to any receptacle until you have verified proper polarity and grounding. Do not plug the shore power cord into a campsite receptacle(s): that has reverse polarity with non-functioning ground circuits that shows outward signs of heat damag...
Page 87: Section 6: Electrical System
85 section 6: electrical system 3. Plug the power cord into the receptacle. Be sure all the power cord prongs are properly plugged into the receptacle. 4. Return to your rv and turn “on” the load center main circuit breaker. The shore line power cord should be unplugged when the recreation vehicle i...
Page 88: Section 6: Electrical System
86 section 6: electrical system if your lights are dimming or flickering that usually indicates an overloaded converter. Remove some of the load by turning off dc lights or appliances. Fan is controlled by load. It will begin running at 3 to 6 amp dc draw. It increases in speed with a higher load un...
Page 89: Section 6: Electrical System
87 section 6: electrical system converter w/charge wizard (if so equipped) some converters may be equipped with a charge wizard there are (3) possible charging modes; normal, boost and storage. The charge wizard will automatically select the best mode to charge your battery. A green led next to the ...
Page 90: Section 6: Electrical System
88 section 6: electrical system replacing a fuse before replacing a fuse, always turn off the electrical components protected by it. 1. Disconnect the shore power cord. 2. Turn “off” the inverter (if so equipped). 3. Disconnect the house or auxiliary batteries main negative battery cable. 4. Remove ...
Page 91: Section 6: Electrical System
89 section 6: electrical system house batteries your motor home is equipped with group 27 deep cycle batteries. Unless a battery has been fully discharged, house auxiliary batteries are normally charged in one of two ways: when the power cord is plugged into 120-volt shore power, or when the generat...
Page 92: Section 6: Electrical System
90 section 6: electrical system refer to your chassis guide for information pertaining to the chassis batteries. 12-volt battery disconnect the 12-volt battery disconnect switch is typically located near the entrance door. This momentary switch controls a solenoid which connects or disconnects the h...
Page 93: Section 6: Electrical System
91 section 6: electrical system the auxiliary start switch can momentarily connect both the house and chassis batteries should the chassis battery become discharged. To operate, depress either the “aux. Start” switch (located on the front driver’s dash) or the battery boost switch on the driver cons...
Page 94: Section 6: Electrical System
92 section 6: electrical system replacement circuit breakers must be of the same voltage, amperage rating and type. Never use a higher rated replacement circuit breaker; doing so may cause a fire by overheating the rv wiring. Replacement only replace circuit breakers with those of the same specified...
Page 95: Section 6: Electrical System
93 section 6: electrical system 120 volt system air cconditioner 18 amps coffee maker 6-12 amps converter (each) 8 amps dvd system 3 amps fireplace 12 amps hair dryer or curling iron 10-14 amps microwave 12 amps refrigerator 6 amps satellite receiver 2 amps tv 2-4 amps vacuum cleaner 8 amps washer/d...
Page 96: Section 6: Electrical System
94 section 6: electrical system do not hook up the power cord to any receptacle until you have verified proper polarity and grounding. Polarity indicators can be purchased in most electrical and hardware stores. Do not use any cheater plug, adapter or extension cord to reconfigure incoming ac power ...
Page 97: Section 6: Electrical System
95 section 6: electrical system generator your motor home may be equipped with an lp or diesel powered generator. The generator in your motor home produces 120/240-volt power compatible with the motor home electrical system. It can be used to power the entire motor home when 120/240-volt shore power...
Page 98: Section 6: Electrical System
96 section 6: electrical system carbon monoxide is deadly! Do not run the generator when your motor home is indoors or in a confined space. Asphyxiation or carbon monoxide poisoning hazards exist whenever generator exhaust gasses can accumulate. Moving parts and electricity can cause severe personal...
Page 99: Section 6: Electrical System
97 section 6: electrical system starting the generator ags (automatic generator start) the magnum® standalone ags system monitors your battery system or surrounding temperature and starts the generator when the battery requires charging or power is needed to run the air conditioner. The ags system u...
Page 100: Section 6: Electrical System
98 section 6: electrical system solar prep (if so equipped) your motor home may be equipped with a roof mount solar panel quick connection. This allows a (customer purchased) solar panel to be installed permanently on the roof. Installation will consist of the solar panel(s), regulator and wiring/fu...
Page 101: Fuel Safety
99 section 7: fuel & propane system fuel safety fuel selection the generator is also fueled by the same system used to fuel the chassis engine. Check the generator manufacturer and the chassis manufacturer information to help determine the type of fuel best suited for this dual application. Fuel fil...
Page 102
100 section 7: fuel & propane system windows should be closed while driving or running the generator (if so equipped) to avoid drawing dangerous exhaust gases into the motor home. If you suspect that exhaust fumes are entering the passenger compartment, have the cause determined and corrected as soo...
Page 103
101 section 7: fuel & propane system the following label should be kept permanently affixed to the motor home: propane gas container propane is a true gas compressed into a liquid form. As the fuel is released from the container, it changes to vapor which is then used for the operation of the applia...
Page 104
102 section 7: fuel & propane system servicing or filling because the container is not removable, the motor home will need to be driven to a qualified propane facility for servicing or filling. Only the authorized gas service technician(s) should be near the motor home while the propane tank is bein...
Page 105: Propane Use and Safety
103 section 7: fuel & propane system note: regulator appearance and type may vary by model. Single stage regulator some models are equipped with a single stage regulator. Two stage regulator the two-stage regulator has the only moving components in the propane system. Its sole function is to reduce ...
Page 106
104 section 7: fuel & propane system apply the soapy solution to the outside of the gas piping fittings. If a leak is present, the soapy solution will “bubble” at the leak point. If a leak is indicated, shut off the propane system valve(s) and contact your dealer or qualified propane service represe...
Page 107
105 section 7: fuel & propane system ensure a supply of fresh air (canada units only) cooking / comfort heating label as the danger of asphyxiation is greater when the appliance is used for long periods of time. Failure to comply may result in death or serious injury. These warning labels are locate...
Page 108
106 section 7: fuel & propane system use care when fueling your motor fuel tanks and/ or propane containers. Make certain your propane tank is properly fastened in place. This label should be kept permanently affixed to your recreation vehicle. Refueling warning label table of contents maintenance r...
Page 109: Section 8: Plumbing System
107 section 8: plumbing system plumbing system there are two different water systems in your recreation vehicle: the fresh water system consists of the fresh water holding tank, faucets and connections, water pump, outside shower assembly (if so equipped), water heater, tub/shower, and water purific...
Page 110: Section 8: Plumbing System
108 section 8: plumbing system operation press only one tact switch at a time. As you push either the fresh, blk grey1 or grey2 switch, one or more led lights will illuminate (from left to right) indicating the content level for that tank. When pushing the “batt” switch, the led lights illuminate fr...
Page 111: Section 8: Plumbing System
109 section 8: plumbing system fresh water system all water contains contaminant and mineral particles that can cause fresh water system odors. Untreated well water is a major source of water system odors. The fresh water (potable water) system needs periodic sanitization and winterization to take c...
Page 112: Section 8: Plumbing System
110 section 8: plumbing system once activated, the water pump (also known as the demand pump) will self-prime, and provide water. The pump is designed for intermittent use only. Using the pump continuously or with high pressure will shorten the life of the pump and is not covered in your warranty. P...
Page 113: Section 8: Plumbing System
111 section 8: plumbing system filter housing note: there is no bypass feature on a canister style water filter. The water filter must be removed before sanitizing or winter- izing the rv. 5. Clean the inside of the filter housing with mild detergent. Thoroughly rinse and wipe clean. 6. Remove the o...
Page 114: Section 8: Plumbing System
112 section 8: plumbing system low point drains exterior fresh water drain 4. Open the “low point drains” by turning, then pulling the handles up. They are installed at the lowest point of the water lines. A label is placed on the outside of the rv to indicate where the drains are located. The drain...
Page 115: Section 8: Plumbing System
113 section 8: plumbing system the city water connection inlet is located in the uni-dock utility center. Use a non-toxic drinking water hose dedicated only to supplying fresh water. To prevent contamination, keep the non-toxic drinking water hose from coming into contact with the ground. Install th...
Page 116: Section 8: Plumbing System
114 section 8: plumbing system (d) red handle pointing up 3. Connect the other end of the hose to a pressurized fresh water source (faucet or spigot). 4. Turn the pressurized water source on, the tank should begin filling. 5. When water has reached the desired level, turn the pressurized water sourc...
Page 117: Section 8: Plumbing System
115 section 8: plumbing system “city water” (pressurized fresh water source) 1. Connect the fresh water hose to the city water inlet. 2. Set the color coded valves to the city water setting: (a) white handle pointing down (b) blue handle pointing left (c) green handle pointing left (d) red handle po...
Page 118: Section 8: Plumbing System
116 section 8: plumbing system 9. Leave the valves set on winterize setting. Sanitizing the plumbing system: when to sanitize: when your rv is new. At the beginning and end of each season. When the water system becomes contaminated or every three months of use. How to sanitize 1. Turn water heater p...
Page 119: Section 8: Plumbing System
117 section 8: plumbing system full. Disconnect the hose from utility center. 7. After the recommended amount of sanitizing solution is in the tank make sure the water tank is full, the cartridge water filter (if so equipped) is bypassed or the filter is removed from the full system canister water f...
Page 120: Section 8: Plumbing System
118 section 8: plumbing system 16. Drain the fresh water system again. If the rv has the full system canister water filter, remove the canister, reinstall the filter, and reattach the canister. 17. Refill the fresh water tank with fresh water again and when water heater is full of water, turn the wa...
Page 121: Section 8: Plumbing System
119 section 8: plumbing system 5. Close all faucets including outside shower. Turn pump off. 6. Drain the system again, but do not drain the water heater (water heater power still off). 7. Close low point drains and fresh water tank drain. 8. Refill the fresh water tank with clean potable water. Use...
Page 122: Section 8: Plumbing System
120 section 8: plumbing system refer to sanitizing the plumbing system section for an explanation of docking station valve positioning and routing information. The preferred method to winterize your recreation vehicle is by using rv antifreeze in the plumbing system. It may be easier to winterize th...
Page 123: Section 8: Plumbing System
121 section 8: plumbing system 6. On full system canister water filters (if so equipped), remove the canister, take out the filter, and reattach the empty canister. 7. Appliances (refrigerator, dishwasher or clothes washer) must be winterized. Refer to the appliance owner’s manual for additional inf...
Page 124: Section 8: Plumbing System
122 section 8: plumbing system truma® tankless water heater (if so equipped) your motor home may be equipped with a truma® tankless water heater. The tankless water heater has no pilot light and supplies an unlimited supply of hot water on demand. The tankless water heater does not require an anode ...
Page 125: Section 8: Plumbing System
123 section 8: plumbing system opening the exterior water heater panel: turn the locking knob, and open the exterior water heater panel to the first open position (a).To open the panel to the second (or service position), the door must first be open as shown in the first photo. Then lift the door so...
Page 126: Section 8: Plumbing System
124 section 8: plumbing system maintenance inspect your water heater monthly and have it serviced at least once a year by the manufacturer’s recommended service technician. Contact your rv dealer, the manufacturer, or customer service. Pressure - temperature relief valve this valve is a safety compo...
Page 127: Section 8: Plumbing System
125 section 8: plumbing system water heater should be off, water pump off, and fixtures open to relieve pressure on the plumbing system. Do not drain when appliance is hot or under pressure. Open the water heater exterior door to the “service” position hanging by the straps. Open the drain chute by ...
Page 128: Section 8: Plumbing System
126 section 8: plumbing system plumbing bypass valves so no water or antifreeze will enter the water heater. Then winterize your rv waterlines with antifreeze as normal. (refer to winterizing the plumbing system) decalcification: lime scale occurs as a result of precipitation from “hard” water. The ...
Page 129: Section 8: Plumbing System
127 section 8: plumbing system 17. Turn the rotary control dial inside the rv to “clean”. If decalcification does not start, make sure power to the water heater is turned on. The yellow status led will flash slowly (1 sec on, 1 sec off) during decalcification. Rinsing the system: 1. Open all fixture...
Page 130: Section 8: Plumbing System
128 section 8: plumbing system note: the shower head may be removed from the hose so that it will drain faster. If you remove the shower head, be sure to reas- semble it prior to storage. Note:when putting the shower assembly back into the storage compartment, make sure the hose is not pinched or th...
Page 131: Section 8: Plumbing System
129 section 8: plumbing system the shower faucet includes a vacuum breaker for the shower. There are two purposes for this breaker: to prevent siphoning water through the hose from another fixture. To prevent water from being retained in the hose. The showerhead does not have a complete shut-off val...
Page 132: Section 8: Plumbing System
130 section 8: plumbing system roof and must be kept clear of obstructions to perform as intended. On some models, the vent pipe may be part of the drainage system referred to as a “wet vent” (water flows downward as air flows upward in the same pipe). Some models are equipped with a side vent syste...
Page 133: Section 8: Plumbing System
131 section 8: plumbing system black / gray tank drains w/macerator system macerator pump system your motor home is equipped with a macerator pump system used to discharge waste from the gray and black waste tank. The system has a 1-1/2-inch diameter flexible hose located beneath the utility center ...
Page 134: Section 8: Plumbing System
132 section 8: plumbing system tank heaters (if so equipped) your recreation vehicle may be equipped with heaters for the fresh, gray, black water tanks and the water lines or drain lines. The larger tank heaters are 120vac and attach directly to the tanks. Water line or drain line heaters are small...
Page 135: Section 8: Plumbing System
133 section 8: plumbing system 44°f (7°c) and will turn off at 64°f (18°c). All of the heaters are controlled by a single on/off switch. Typically, this red tank heater on/off switch is located on the command center panel or in the bathroom. The switch lights up red when it is turned on and controls...
Page 136: Section 8: Plumbing System
134 section 8: plumbing system always have four to six inches (10 - 15 cm) of water in the toilet. It is important to add enough water to prevent solid waste buildup. The following guidelines will help to prevent solid waste buildup. Sewage (black) tank preparation 1. Release one to two quarts (1 or...
Page 137: Air Conditioner
135 section 9: heating and cooling air conditioner the air conditioning system is controlled by a thermostat. Cooled air enters the rv through the grill. Make sure you have sufficient power available before operating the air conditioner. Do not operate the air conditioner without the return air filt...
Page 138: Furnace
136 section 9: heating and cooling furnace the furnace installed in your recreation vehicle is controlled by a 12-volt dc thermostat. Depending on your model, there may be up to two thermostats enabling you to control the temperature to your comfort level. The furnace requires both 12-volt power and...
Page 139: Section 10: Appliances
137 section 10: appliances microwave for details on operation, cleaning and safety information, refer to the manufacturer’s user guide. General cleaning microwave and convection microwave important: before cleaning, make sure all controls are off and the microwave oven is cool. Always follow label i...
Page 140: Section 10: Appliances
138 section 10: appliances cooktops; range & oven (if so equipped) for detailed operating and safety information, refer to the manufacturer’s user guide. Cleaning instructions refer to the manufacturer’s user guide included for detailed cleaning instructions. General cleaning to avoid damage and pos...
Page 141: Section 10: Appliances
139 section 10: appliances gas drop-in cooktops (if so equipped) depending on your model, it may be equipped with either a 2 burner or 3 burner cooktop. The 2 burner match-light cooktop has two 6500 btu/h burners with control panel. The 3-burner piezo-igniter cooktop has (1) front 9000 btu/h burner ...
Page 142: Section 10: Appliances
140 section 10: appliances whenever the stove in the rv is being used: the range hood must be turned on, and the inner flap must be unsnapped and free to move. Failure to do so can create an asphyxiation hazard by restricting air flow to this vent. Refrigerator the refrigerator is not intended for q...
Page 143: Section 10: Appliances
141 section 10: appliances contact your dealer or customer service for details on winterizing your refrigerator. Cleaning your refrigerator the following are general cleaning guidelines. For detailed information on cleaning your specific refrigerator, refer to the manufacturer’s user’s guide. Cleani...
Page 144: Section 10: Appliances
142 section 10: appliances water heater – see plumbing section steel cleaner. A spray-on stainless steel cleaner works best. Important: do not allow the stainless steel cleaner and polish to come into contact with any plastic parts such as the trim pieces, dispenser covers or door gaskets. If uninte...
Page 145: Section 11: Electronics
143 section 11: electronics hdtv antenna/satellite system(s) your recreation vehicle may be equipped with an exterior amplified high definition tv antenna. The antenna comes equipped with a signal meter and a power injector to aid in receiving the strongest possible signal when tuning in hdtv statio...
Page 146: Section 11: Electronics
144 section 11: electronics antenna power supply (if so equipped) for good station reception, the antenna power supply must be turned on to view local television stations. Turning the antenna power supply on sends 12-volt dc through the cable to the tv roof antenna. The voltage energizes the transis...
Page 147: Section 12: Interior
145 section 12: interior cleaning the interior to keep the value of your recreation vehicle, perform regular maintenance using the proper materials and procedures. Using the wrong cleaner may result in damage to the surfaces in your vehicle. Check with the manufacturer’s information for the recommen...
Page 148: Section 12: Interior
146 section 12: interior day/night shades: clean with a mild cleaning solution using a sponge or paper towel. Wipe down with water after cleaning and dry thoroughly before raising the shade. Do not use spot remover, household cleaners or detergents to remove soiled spots, as these may cause damage t...
Page 149: Section 12: Interior
147 section 12: interior sofa & dinette your motor home may be equipped with one of the following sofa styles. Hide-a-bed sofa or sofa sleeper the hide-a-bed sofa functions much the same as a regular residential hide-a-bed sofa. To make the hide-a-bed sofa into a bed, remove the seat cushions and pu...
Page 150: Section 12: Interior
148 section 12: interior trifold sofa the trifold sofa offers very similar features to the traditional hide-a-bed. The following illustrations detail converting the sofa into a bed. Booth dinette (if so equipped) the dinette is designed to seat up to four adults. Depending on your model, there may b...
Page 151: Section 12: Interior
149 section 12: interior do not allow occupants to occupy the free standing dinette chairs while the motor home is in transit. Free standing dinette chairs be fastened securely at the dinette table, and the folding chairs be secured in a closet or storage area pantry or hutch (if so equipped) your r...
Page 152: Section 12: Interior
150 section 12: interior solid surface countertops (if so equipped) soapy water, ammonia based cleaners (not window cleaners as they can leave a waxy build up that may dull the surface) or commercially available solid surface cleaners will remove most dirt and residue from all types of finishes. A d...
Page 153: Section 12: Interior
151 section 12: interior privacy drape installation 1. Starting on the driver’s side, attach the black plastic hook to the loop on the wall (behind the driver’s seat). Make sure the velcro® on the drape is facing the motorhome windshield. 2. Pull the drape towards the windshield and past the driver’...
Page 154: Section 12: Interior
152 section 12: interior note: if the ceiling light is left on when raising the bunk, it will automatically turn off as the bed rises regardless of the rocker switch position. Raising the bunk: to raise the cab-over bunk; turn the key switch to the right to the on position, and then press the yellow...
Page 155: Section 13: Exterior
153 section 13: exterior cleaning the exterior to protect your recreation vehicle’s exterior finish, wash it often and thoroughly. For recreation vehicles with painted exterior graphics: if desired you may wash and wax your vehicle 60 days after purchase. The exterior paint does need time to cure be...
Page 156: Section 13: Exterior
154 section 13: exterior stains. They can be dissolved using ammonia based glass cleaner, warm soapy water and a little “elbow grease”. Once again, after removing stubborn stains immediately rinse with clean water. Drying the recreation vehicle is just as important as washing your vehicle. Tap and w...
Page 157: Section 13: Exterior
155 section 13: exterior do not use waxes containing high-abrasive compounds. Such waxes remove rust and stains effectively from the paint work, but they are also harmful to the luster of the painted surface since they scrape off the coating. Further, they are detrimental to glossy surfaces, such as...
Page 158: Section 13: Exterior
156 section 13: exterior note: always have the alignment checked and adjusted by a qualified shop with the proper equipment to handle heavy vehicles. Note: a road test by the dealer should be included as part of the pre-delivery inspection. The dealer can check for and correct any steering problems ...
Page 159: Section 13: Exterior
157 section 13: exterior if your recreation vehicle is equipped with a roof ladder, do not leave items attached to it while traveling. The ladder weight capacity should not be exceeded (see ladder capacity label). Do not exceed this weight limit. There should never be more than one person on the lad...
Page 160: Section 13: Exterior
158 section 13: exterior to check the exterior sidewall sealants, use a stepladder placed safely alongside the vehicle. Do not prop a ladder against the body of the motor home as it may damage the exterior finish table of contents maintenance record.
Page 161: Travel Checklist
159 section 14: travel/camping/storage checklists travel checklist following is a preliminary list of items that need to be checked before leaving your home or campsite. This is a general list, which you may want to customize as you determine your own needs. Refer to your chassis guide for informati...
Page 162: Motor Home Storage
160 section 14: travel/camping/storage checklists turn off propane tanks (if so equipped). Empty black and gray holding tank, rinse as needed. Retract any awnings and secure them for transport. Close all the roof vents. Close windows & latch blinds. Disconnect the cable tv and phone hookups and lowe...
Page 163
161 section 14: travel/camping/storage checklists turn off the motor home 12-volt battery disconnect switch. Turn off the inverter mode at remote. Disconnect the batteries to prevent battery discharge. Remove all perishables from the refrigerator/freezer. Defrost, wash and dry the interior of the re...
Page 164
162 section 14: travel/camping/storage checklists notes: table of contents maintenance record.
Page 165
163 section 15: additional information featured components quick reference chart your recreation vehicle may be equipped with some of the items listed below. This is a partial listing and it is not intended to cover all components. All information is the latest available at the time of publication. ...
Page 166
164 section 15: additional information toilet thetford corp. Www.Thetford.Com water heater, tank dsi water heater, tankless atwood greenbrier girard systems www.Atwoodmobile.Com www.Greenrvproducts.Com water pump, 12v shurflo east www.Shurflo.Com table of contents maintenance record.
Page 167: Vehicle Maintenance Record
165 section 15: additional information vehicle maintenance record make: model: model year: vehicle serial#: engine: engine serial#: service date mileage work performed performed by notes table of contents maintenance record.
Page 168
166 section 15: additional information notes: table of contents maintenance record.
Page 169
167 section 15: additional information jayco ownership notification fax form to: (800) 825-7876 □ change of owner □ transfer of limited warranty (see limited warranty for details) model information: serial#: ______________________ chassis #: _______________________ odometer reading ______________ (m...