JBL CINEMA VISION CVCEN50 Owner's Manual - Speaker Placement

Manual is about: JBL Cinema Vision Data Specificaion

Summary of CINEMA VISION CVCEN50

  • Page 1

    Cvsat50, cvcen50, cvsub50 cinema vision ™ owner’s guide ® cv om 6/15/04 4:06 pm page 1.

  • Page 2: Read First!

    2 read first! Important safety precautions! 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with a dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manu...

  • Page 3: Included

    3 included thank you for choosing jbl for more than 50 years, jbl has been involved in every aspect of music and film recording and reproduction, from live performances to the recordings you play in your home, car or office. We’re confident that the jbl system you have chosen will provide every note...

  • Page 4: Speaker Placement

    4 speaker placement subwoofer surround speakers † 5 – 6 ft 1.5 – 1.8m † front speakers (0-2 ft) 0-0.6m the front speakers should be placed the same distance from each other as they are from the listening position. They should be placed at about the same height from the floor as the listeners’ ears w...

  • Page 5: Mounting Options

    5 mounting options on shelves using the optional cvts50 table stands. On the wall. Wall brackets are included. On compatible floor stands avail- able from other manufacturers, using the supplied floor stand adaptors. Satellites and surrounds important safety notes: • the table stand consists of two ...

  • Page 6

    6 mounting the satellites on optional floor stands important safety note: the supplied floor stand adaptors facilitate installation with a variety of general- purpose floor stands available from many manufacturers. Since different stands will have different weight capaci- ties and stability characte...

  • Page 7

    7 important safety note: the customer is solely responsible for proper selec- tion of mounting hardware not included with the speak- ers, and for proper assembly and installation of the wall brackets, including but not limited to the selection of appropriate weight-bearing supports and proper use of...

  • Page 8: Speaker Connections

    8 connection tips speaker connections separate and strip the ends of the speaker wire as shown. The wires sup- plied with the system may already be stripped and tinned for easy insertion into the speaker terminals. You may need to separate the two conductors further in order to thread them through t...

  • Page 9

    9 the cvsub50 subwoofer is equipped with only one input – a dedicated low- frequency effects (lfe) input. Since the lfe channel is by definition limited to only the lowest portion of the fre- quency spectrum, it is cru- cial that your receiver’s out- put be compatible. The cvsub50 should only be use...

  • Page 10: Subwoofer Operation

    10 subwoofer operation press the master power switch (marked “power” å) in to the on position to use the subwoofer. The cvsub50 subwoofer will automatically turn on or go into standby (sleep) mode as described below. When your receiver or amplifier is off, or is not sending program material to the s...

  • Page 11: Troubleshooting

    If there is no sound from any of the speakers: • check that receiver/ampli- fier is on and a source is playing. • check that the powered subwoofer is plugged in, and is turned on (power switch å pushed in). • check all wires and con- nections between receiver/ amplifier and speakers. Make sure all w...

  • Page 12: Specifications

    12 system frequency response 22hz – 20khz (–6db) cvsat50 maximum recommended amplifier power 150 watts** power handling 50w continuous/300w peak frequency response 55hz – 30khz (–6db) nominal impedance 8 ohms sensitivity 90db @ 1 watt/1 meter tweeter one 3/4" (19mm) titanium-laminate dome, video-shi...