Summary of Control CRV
Page 1
Jbl control ® crv owner’s manual.
Page 2
Jbl control® crv loudspeakers jbl control crv speakers are perhaps the most fl exible and versatile loudspeakers ever developed. There are numerous mounting options. The jbl control crv speaker can be wall- mounted or corner-mounted, or two, three or four speakers can be joined together to create lo...
Page 3
Wall surface mounting when deciding upon a location for the jbl control crv speaker, take care not to install the mounting bracket closer than 3” (7.6 cm) (horizontal) and 8-1/2” (21.5 cm) (vertical) to the ceiling. Any closer than the minimum measurements will not allow the clearance needed to posi...
Page 4
7. Vertical bracket orientation —regardless of whether you choose a vertical or horizontal orientation for the speaker,when mounting the jbl control crv speaker to a single wall surface, you should always install the wall-mounting bracket in a vertical orientation, as shown. An alternate vertical or...
Page 5
3. Connect the stripped bare wires to the input terminals of the jbl control crv speaker. 4. Set the tap selector switch to the desired 70v/100v tap, or to the thru position for 4 ohm low-impedance operation. 5. The mounting bracket is designed to trap the fl ange of the jbl control crv speaker by s...
Page 6
Wall ceiling mounting (vertical speaker orientation) when deciding upon a location for the jbl control crv speaker, take care not to install the mounting bracket closer than 3” (7.6 cm) to a side wall. Any closer than 3” (7.6 cm) will not allow the clearance needed to position and slide the jbl cont...
Page 7
6. To orient the jbl logo into the correct position, pull the jbl logo slightly outward from the speaker grille and rotate. The jbl logo is held in place by a spring. Peel the adhesive cover off the mounting-bracket cover and attach to the top and bottom of the mounting assembly. Half-round wall mou...
Page 8
2. Attach the mounting bracket to the wall. Be sure to use appropriate anchors. 3. Connect the stripped bare wires to the input terminals of the jbl control crv speakers. 4. Set the tap selector switches to the desired 70v/100v tap. Thru position is not advised due to parallel speakers providing too...
Page 9
When deciding upon a location for the jbl control crv speaker, take care not to install the mounting bracket closer than 3” (7.6 cm) to the ceiling. Any closer than 3” (7.6 cm) will not allow the clearance needed to position and slide the jbl control crv speaker into the mounting bracket. 2. Attach ...
Page 10
7. Rest the third jbl control now speaker’s rear fl ange in the mounting bracket as shown and complete the process. Secure the mounting-bracket cap with 2 screws through the bottom of the mounting bracket. 8. To orient the jbl logo into the correct position, pull the jbl logo slightly outward from t...
Page 11: Caution:
Unpacking the bracket and cable kit carefully unpack the bracket and cable assembly. If you suspect damage from transit, report it immediately to your dealer and/or delivery service. Keep the shipping carton and packing materials for future use. Open the package and verify the following contents: in...
Page 12
For smaller-diameter drop tubes 2b. When using a smaller drop tube, use the pole bushing when running the wiring down through pole-mount-bracket cap. This will help to eliminate pole wobble. 3. Slide the clevis pin through the aligned holes in the pole- mount bracket and drop tube. Secure the clevis...
Page 13
3. After carefully placing all four speakers in the mounting bracket, lightly jostle the speakers into place so that the pole- mount-bracket cap will slide down into place. Tighten the pole- mount-bracket assembly with the four #10-32 x 2” (m5 51 mm) screws provided. 4. Place the pole-mount-bracket ...
Page 14
Painting control crv the loudspeakers can be painted to match the decor. The speaker accepts almost any type of latex or oil based paint. For best results, the following procedure is recommended: 1. Remove the grille. 2. Mask the baffl e of the speakers -- it’s almost always advisable to keep the ba...
Page 15
Specifications frequency range (–10db) 1 : 80hz – 20khz power handling 2 : 75 w continuous pink noise, 2 hrs 60 w continous pink noise, 100 hrs 150 w continuous program power 300 w continous peak power nominal sensitivity: 89 db maximum spl @ 1m 3 : 108 db continuous average long-term (peaks of 114 ...
Page 16
Dimensions 262 mm (10.3 in) 364 mm (14.4 in) 251 mm (9.9 in) 127 mm (5 in) jbl professional 8500 balboa boulevard, p.O. Box 2200 northridge, ca 91329 usa om cntrl crv 15m 5/09.